Summary of the content on the page No. 1
Model No. WESY59100
Serial No.
USER'S MANUAL
Write the serial number in the space
above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR
TOLL-FREE CUSTOMER
HOT LINE. The techni-
cians on our customer
hot line will provide
imme
Summary of the content on the page No. 2
TABLE OF CONTENTS LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . .
Summary of the content on the page No. 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the training system. 1. It is the responsibility of the owner to ensure 9. Always disconnect the lat bar from the train- that all users of the training system are ade- ing system when performing an exercise that quately informed of all precautions. does not use the lat bar. 2. Read all instructions in this manual and in 10. Always wear athletic shoes for foot protec- the acc
Summary of the content on the page No. 4
BEFORE YOU BEGIN ® Thank you for selecting the versatile WEIDER 9600 Department toll-free at 1-800-999-3756, Monday ® PRO training system. The WEIDER 9600 PRO offers through Friday, 6 a.m. until 6 p.m. Mountain Time a selection of weight stations designed to develop (excluding holidays). To help us assist you, please every major muscle group of the body. Whether your note the product model number and serial number goal is to tone your body, build dramatic muscle size before calling. The model nu
Summary of the content on the page No. 5
ASSEMBLY Make sure you have the following tools: Make Assembly Easier! • Two (2) adjustable wrenches Everything in this manual is designed to ensure that the training system can be • One (1) standard screwdriver assembled successfully by anyone. Before • One (1) phillips screwdriver beginning assembly, make sure to read the information on this page. This brief intro- • One (1) rubber mallet duction will save you much more time than it takes to read it! • You will also need grease or petrole
Summary of the content on the page No. 6
1 83 48 62 FRAME ASSEMBLY 50 48 1. Before you begin this step, make sure that 4 you have read all of the information on page 6 5. This brief introduction will save you much more time than it takes to read it. 92 92 Locate and open the parts bags labeled “FRAME 83 ASSEMBLY.” 92 83 See the inset drawing. Insert two 1 1/2” x 2 1/2” 92 4 83 Inner Caps (83) and two 3/8” x 2” Carriage Bolts (92) into the Butterfly Base (4). 2 Insert two 1 1/2” x 2 1/2” Inner Caps (83) into the 50 1 indicated ends of t
Summary of the content on the page No. 7
5. Attach the Butterfly Seat Frame (14) to the Butterfly 5 50 Upright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8” 1 Flat Washers (48), and two 3/8” Nylon Locknuts 62 (50). 50 Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 1/4” Bolts (62), two 50 14 48 3/8” Flat Washers (48) and two 3/8” Nylon Locknuts 50 (50). 48 3 Do not tighten the Nylon Locknuts yet. 62 6. Press a 2 1/2” Square Inner Cap (76) into the Press 6 Front Leg (20). 76 Attach the Press Front
Summary of the content on the page No. 8
9. See the inset drawing. Insert two Weight Inserts 9 (56) into each Weight (21). 56 15 Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). 21 Slide the Weight Guides (15) through the Weight Bumpers (51) and the holes in the Press Base (6). Secure the Weight Guides to the Press Base with 21 two 3/8” x 2 3/4” Bolts (89), four 3/8” Flat Washers Slot (48), and two 3/8” Nylon Locknuts (50). 89 51 89 Slide the Weights (21) onto the Weight Guides (15), stacking the
Summary of the content on the page No. 9
12. Secure the Press Top Frame (9) to the Butterfly Top 12 Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 50 3/8” Flat Washers (48), and two 3/8” Nylon 62 48 Locknuts (50). Do not tighten the Nylon Locknuts yet. 9 48 33 13. Secure the Weight Guides (15) to the Press Top 13 57 Frame (9) with two 3/8” x 1 3/4” Bolts (57) and two 3/8” Nylon Locknuts (50). Tighten the Nylon Locknuts used in steps 2–13. 9 50 50 15 14 ARM ASSEMBLY 33 14. Locate and open the parts bag labeled “ARM ASSEMBLY.” Lubrica
Summary of the content on the page No. 10
15. Insert a 2” Square Inner Cap (28) into the end of 15 the Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm 10 (10) with two 3/8” x 1” Bolts (84) and two 3/8” Flat Washers (48). 48 48 10 53 Repeat this step with the other Butterfly Arm (10). 84 53 28 48 48 28 16. Lubricate a 3/8” x 3 1/4” Bolt (62). Attach the left 16 Butterfly Arm (10) to the Left Pivot Arm (71) with 50 the Bolt and a 3/8” Nylon Locknut (50). 10 Repeat this step with the right Butterfly Arm (not shown)
Summary of the content on the page No. 11
19. Attach a Bumper (40) to the Press Front Leg (20) 19 with a 1” Tap Screw (80). 78 Press a 2” x 3” Inner Cap (78) into the top of the Press Leg Lever (90). 90 Lubricate a 1/2” x 4” Bolt (68). Attach the Press Leg 40 Lever (90) to the Press Base (6) with the Bolt and a 1/2” Nylon Jamnut (36). Note: Do not over tighten 20 the Nylon Jamnut; the Press Leg Lever must be able to pivot easily. 80 68 6 Lubricate 36 20. Insert two 2” Square Inner Caps (28) into the Leg Lever (41). 20 Lubricate 88 Attac
Summary of the content on the page No. 12
23. Remove the preassembled 3/8” x 2” Bolts (54) from 23 one set of Adjustable Pulley Plates (23). Wrap the Butterfly Cable (73) around a 3 1/2” 54 Pulley (24). Attach the 3 1/2” Pulley and a Cable 25 24 Trap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50). Be sure that the Cable Trap is turned to hold the Cable in place. 73 50 23 24. Wrap the Butterfly Cable (73) around a “V”-Pulley 24 (27). Attach the “V”-Pulley and a Lar
Summary of the content on the page No. 13
27. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). 27 66 Insert the Ab Cable down through the Press Top Frame (9). Attach a 3/8” Flat Washer (48) and a 24 5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). 62 48 Slide the Bolt through the Press Top Frame and the 3 1/2” Pulley. Secure another 5/8” x 3/4” Bushing 50 48 and 3/8” Flat Washer to the Bolt with a 3/8” Nylon Locknut (50). 47 9 28. Remove the preassembled 3/8” x 2” Bolts (54) from 28 the other Adjustable Pulley Plates (23). Wrap
Summary of the content on the page No. 14
31. Locate the Weight Cable (72). Note that one end 31 of the Weight Cable has a bolt, and the other end has a ball on it. Lay the Weight Cable (72) inside the bracket on the 3 Butterfly Base (4) in the manner shown. Attach a 3 24 54 1/2” Pulley (24) to the bracket with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50). Be sure the Weight Cable is in the groove of the 3 1/2” 72 4 Pulley. 50 Bracket 32. Wrap the Weight Cable (72) around a 3 1/2” Pulley 32 (24). Attach a 3/8” Flat Washer (48) a
Summary of the content on the page No. 15
35. Wrap the Weight Cable (72) around a 3 1/2” Pulley 35 (24). Attach the 3 1/2” Pulley and a Cable Trap (25) 1 to the Butterfly Upright (1) with a 3/8” x 4” Bolt (59), 59 a 3/8” Flat Washer (48), and a 3/8” Nylon Jamnut (63). Be sure that the Cable Trap is turned to hold the Cable in place. 24 25 72 48 63 36. Wrap the Weight Cable (72) around a 3 1/2” Pulley 73 36 (24). Attach the 3 1/2” Pulley and a Cable Trap (25) 54 between the lowest holes of the Adjustable Pulley Plates (23) hanging from t
Summary of the content on the page No. 16
39. Wrap the Weight Cable (72) around a 3 1/2” Pulley 39 47 (24). Attach the 3 1/2” Pulley and a Cable Trap (25) between the lowest holes in the Adjustable Pulley 23 Plates (23) hanging from the Ab Cable (47) with a 54 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50) 25 50 that was removed in step 28. Be sure that the Cable Trap is turned to hold the Cable in place. 24 72 40. Remove the preassembled 3/8” x 1 3/4” Bolts (57) 40 from the Small Pulley Plates (22). Wrap the Weight Cable (72) around
Summary of the content on the page No. 17
43. Locate the Leg Press Cable (75). Attach the Leg 43 Press Cable to the indicated side of the Press Upright (2) with a 3/8” x 3 1/4” Bolt (62) and a 3/8” Nylon Locknut (50). Do not tighten the Nylon 62 Locknut yet. 7 Wrap the Leg Press Cable (75) up around a 3 1/2” 2 Pulley (24) in the direction shown. Attach the 3 1/2” 75 60 Pulley and a Cable Trap (25) to the indicated side of the Press Frame (8) with a 3/8” x 4 3/4” Bolt (60) 24 and a 3/8” Nylon Locknut (50). Do not tighten the Nylon Locknu
Summary of the content on the page No. 18
47. Remove the 3/8” Nylon Locknut (50) from the indi- 47 cated 3/8” x 5 1/2” Bolt (55). 76 Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the 3 1/2” Pulley and a Cable Trap (25) to the 3/8” x 5 1/2” Bolt (55) on the indi- cated side of the Press Base (6) with the 3/8” Nylon 24 Locknut (50). Be sure the Cable Trap is oriented to hold the Cable in place. Press a 2 1/2” Square Inner Cap (76) into the Press 55 Base (6). 25 6 50 75 48. Remove the 3/8” Nylon Jamnut (63) from the in
Summary of the content on the page No. 19
51 SEAT ASSEMBLY 14 13 51. Locate and open the parts bag labeled “SEAT ASSEMBLY.” Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49). Repeat this step with the other Seat (not shown) 49 and the Press Seat Frame (not shown). 52. Press a 1 1/2” Square Inner Cap (35) into the end 52 of the Press Backrest Frame (44). Attach a 2 49 Backrest (12) to the Press Backrest Frame with four 44 1/4” x 3/4” Bolts (49). 5 Pull out the Adjustment Knob (5) on the
Summary of the content on the page No. 20
55. Lubricate a 1/2” x 4” Bolt (68). Attach the Foot 55 Lubricate Press Plate (29) to the Press Leg Lever (90) with 68 90 the Bolt and a 1/2” Nylon Jamnut (36). 36 29 56. Press two 3/4” Round Inner Caps (43) into each of 56 Welded the two Pad Tubes (42). Tube Slide a Foam Pad (30) onto one side of a Pad Tube (42). Slide the Pad Tube through the hole in the 30 Leg Lever (41). Slide another Foam Pad onto the other side of the Pad Tube. 42 Slide a Foam Pad (30) onto one side of the other 41 Pad Tu