Summary of the content on the page No. 1
Model No. WESY47330
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
custo
Summary of the content on the page No. 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ASSEMBLY . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
WARNING DECAL PLACEMENT The decals shown here have been placed on the weight system. If a decal is missing or illegible, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time, to order a free replacement decal. Apply the decal in the location shown. Decal 3 Decal 1 Decal 1 Keep hands and fingers clear of this area. Decal 2 Decal 2 • Keep clear of Decal 3 this area. Decal 2 Decal 3 3
Summary of the content on the page No. 4
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual before 9. The weight system is designed to support a using the weight system. Use the weight sys- maximum user weight of 300 pounds. The tem only as described in this manual. weight system is designed to be used by only one person at a time. 2. It is the responsibility of the owner to ensure that all users of the wei
Summary of the content on the page No. 5
BEFORE YOU BEGIN ® Thank you for selecting the versatile WEIDER CLUB tions, please call our Customer Service Department toll- C4800 weight system. The weight system offers a free at 1-800-999-3756, Monday through Friday, selection of weight stations designed to develop every 6 a.m. until 6 p.m. Mountain Time (excluding holidays). major muscle group of the body. Whether your goal is to To help us assist you, please note the product model tone your body, build dramatic muscle size and number and
Summary of the content on the page No. 6
ASSEMBLY Make sure you have the following tools: Make Assembly Easier for Yourself • Two adjustable wrenches Everything in this manual is designed to • One standard screwdriver ensure that the weight system can be assem- bled successfully by anyone. Before begin- • One phillips screwdriver ning assembly, make sure to read the information on this page. This brief intro- • One rubber mallet duction will save you much more time than •You will also need grease or petroleum jelly, a it takes to r
Summary of the content on the page No. 7
1 Frame Assembly 46 46 1. Before beginning assembly, make sure you understand the information in the box on 1 page 6. Refer to the PART IDENTIFICATION CHART in the center of this manual for help identifying small parts. 85 Press four 50mm x 75mm Inner Caps (46) into 46 the Base (1) and the Leg Press Base (3). Insert three M10 x 92mm Carriage Bolts (85) and 101 an M10 x 121mm Carriage Bolt (49) up into the 3 Base (1). 49 85 Slide the Leg Press Base (3) onto the indicated M10 x 92mm Carriage Bol
Summary of the content on the page No. 8
3. Press a 50mm Thick Square Inner Cap (47) into 3 the Leg Lever Base (5). Press two 50mm x 75mm Inner Caps (46) into the Foot Plate (6). 2 47 Attach the Leg Lever Base (5) to the Butterfly Upright (2) with two M10 x 75mm Bolts (82), an M10 x 95mm Bolt (105), an M10 Washer (99), and three M10 Nylon Locknuts (101). Do not 5 tighten the Locknuts yet. 101 105 Attach the Foot Plate (6) to the Leg Lever Base 99 (5) with two M10 x 65mm Carriage Bolts (88) and 101 46 101 two M10 Nylon Locknuts (101). D
Summary of the content on the page No. 9
5. Slide two Weight Bumpers (71) onto the Weight 5 18 25 Guides (18). Slide eight Weights (22) onto the Weight Guides (18). Make sure the Weights are oriented with Lubricate the pin grooves on the side shown. Pin Press a Weight Tube Bumper (54) into the Long Weight Tube (23). Insert the Long Weight Tube 23 into the Weights (22). Lubricate the indicated holes in a Top Weight (25) with grease. Slide the Top Weight onto the Weight 54 Guides (18). Make sure the pin on the Long Weight Tube (23) rest
Summary of the content on the page No. 10
7. Press a 50mm x 75mm Inner Cap (46) into the 7 Top Frame (9). Slide the welded tubes on the Top Frame (9) over 9 the upper ends of the Weight Guides (18, 19). 101 101 Attach the Top Frame (9) to the Butterfly Upright 82 (2) with two M10 x 75mm Bolts (82) and two M10 Nylon Locknuts (101). Do not tighten the Locknuts yet. 51 Attach the Top Frame (9) to the Weight Guides 2 (18, 19) with four M10 x 45mm Bolts (51) and four M10 Nylon Locknuts (101). Do not tighten 18 46 the Locknuts yet. 19 8. Pre
Summary of the content on the page No. 11
10 Arm Assembly 101 45 Lubricate 10. Attach the Leg Lever Bumper (60) to the Leg Lever Base (5) with an M4 x 25mm Self-tapping Screw (103) and an M4 Washer (104). 79 60 96 Press two 50mm Square Inner Caps (45) and two 7 5 M10 Round Bushings (79) into the Leg Lever (7). 103 Lubricate an M10 x 85mm Bolt (96) with grease. 104 Attach the Leg Lever (7) to the Leg Lever Base (5) with the Bolt and an M10 Nylon Locknut (101). Do not overtighten the Locknut; the Leg Lever must be able to pivot easily. 45
Summary of the content on the page No. 12
13. Attach a Seat Arm (26) to the Sliding Seat Frame 13 (8) with two M6 x 35mm Bolts (83) and two M6 Nylon Locknuts (102). Repeat with the other Seat Arm (26). 26 102 8 83 26 14. Press a 50mm Thick Angled Cap (109) into the 14 top of the Rear Press Arm (13). Press a 50mm Angled Cap (108) into the top of the Front Press 109 Arm (14). 108 13 Lubricate an M10 x 77mm Bolt (106) with grease. Attach the Rear Press Arm (13), which has a hole 14 in the lower area, to the Leg Press Base (3) with the Bolt
Summary of the content on the page No. 13
16. Attach the Leg Press Plate (15) to the Leg Press 16 Brackets (16) with two M10 x 85mm Bolts (96), 16 four M10 Thick Spacers (70), and two M10 Nylon 96 Locknuts (101). 15 Note: The four M10 Thick Spacers (70) must be between the Leg Press Brackets (16) and 101 the welded tube on the Leg Press Plate (15). 70 The two holes in the welded tube must be closer to the top of the Leg Press Plate. Welded 70 Tube Tighten the M10 Nylon Locknuts (101) used in step 15. Do not overtighten the Locknuts; th
Summary of the content on the page No. 14
20. Route the Lat Cable (62) up through the Top 20 Frame (9), over a 100mm Pulley (38), and back 38 down through the Top Frame. Attach the Pulley inside the Top Frame with an M10 x 65mm Bolt 69 62 99 (80), two M10 Washers (99), two 12.5mm 101 Spacers (69), and an M10 Nylon Locknut (101). 80 99 69 9 21. Wrap the Lat Cable (62) under a 100mm Pulley 21 (38). Attach the Pulley to the Double “U”-bracket (42) with an M10 x 45mm Bolt (51) and an M10 Nylon Locknut (101). 62 38 101 42 51 22. Route the L
Summary of the content on the page No. 15
25. Identify the Upper Short Stack Cable (63). 25 Attach the Cable inside the Top Frame (9) with an 99 9 M10 x 65mm Bolt (80), two M10 Washers (99), 101 and an M10 Nylon Locknut (101). 99 63 80 26. Wrap the Upper Short Stack Cable (63) under a 26 100mm Pulley (38). Attach the Pulley and a Long 63 Cable Trap (68) to the indicated hole in a “U”- bracket (40) with an M10 x 50mm Bolt (81) and 68 an M10 Nylon Locknut (101). Make sure the 38 Cable Trap is oriented to hold the Cable in the 81 groove of
Summary of the content on the page No. 16
30. Identify the Butterfly Cable (67). Attach the 30 80 Cable inside the Butterfly Upright (2) with an M10 99 x 65mm Bolt (80), two M10 Washers (99), and an M10 Nylon Locknut (101). 101 67 99 2 31. Wrap the Butterfly Cable (67) around a 100mm 31 92 Pulley (38). Attach the Pulley to the Butterfly 10 Frame (10) with an M10 x 213mm Bolt (92), two 99 M10 Washers (99), and an M10 Nylon Locknut (101). 38 67 99 101 32. Wrap the Butterfly Cable (67) around a 100mm 32 Pulley (38). Attach the Pulley to th
Summary of the content on the page No. 17
34. Route the Butterfly Cable (67) through the 34 Butterfly Upright (2) and over a 100mm Pulley (38). Attach the Pulley and a Long Cable Trap 81 (68) to the Butterfly Upright with an M10 x 50mm 38 Bolt (81) and an M10 Nylon Locknut (101). Make 68 sure the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 67 2 101 35. Attach the end of the Butterfly Cable (67) to the 35 67 “U”-bracket (40) with an M8 Washer (100) and an M8 Nylon Locknut (87). Note: Do not complete- ly tighten
Summary of the content on the page No. 18
39. Wrap the Lower Short Stack Cable (64) around a 39 90mm Pulley (39). Attach the Pulley and a Short Cable Trap (48) to the Base (1) with an M10 x 51 45mm Bolt (51). Make sure the Cable Trap is oriented to hold the Cable in the groove of the 48 Pulley. 39 1 64 40. Wrap the Lower Short Stack Cable (64) under a 40 90mm Pulley (39). Attach the Pulley to the Base 64 (1) with an M10 x 45mm Bolt (51), an M10 Washer (99), and an M10 Nylon Locknut (101). 39 101 1 99 51 41. Locate the Weight Plate (20)
Summary of the content on the page No. 19
44. Note: The following steps are shown from the 44 3 back of the weight system. 101 Route the Leg Press Cable (65) under a 100mm 99 Pulley (38). Attach the Pulley and a Long Cable Trap (68) to the Leg Press Base (3) with an M10 38 x 92mm Bolt (55), an M10 Washer (99), and an M10 Nylon Locknut (101). Make sure the Cable Trap is oriented to hold the Cable in the 65 groove of the Pulley. 68 55 45. Wap the Leg Press Cable (65) around a 90mm 45 Pulley (39). Attach the Pulley and a Short Cable 101 Tr
Summary of the content on the page No. 20
49. Route the Ab Cable (66) through the Butterfly 49 Upright (2). Attach a 100mm Pulley (38) inside the Leg Lever Base (5) with an M10 x 65mm Bolt 5 (80), two M10 Washers (99), two 12.5mm Spacers (69), and an M10 Nylon Locknut (101). 38 101 66 99 2 69 69 99 80 50. Note: This step is shown from the back of the 50 weight system. Lay the Ab Cable (66) in the indicated brackets. Attach a 100mm Pulley (38) inside the bracket on the Base (1) with an M10 x 45mm Bolt (51) and 51 an M10 Nylon Locknut (1
