Summary of the content on the page No. 1
Model No. WESY3924.2
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-877-992-5999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.weiderservice.com
USER’S MANUAL
CAUTION
Visit our website at
Read all precaut
Summary of the content on the page No. 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASSEMBLY . . . . . . .
Summary of the content on the page No. 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the resistance system. 1. Read all instructions in this manual and all 11. If you purchase the optional lat bar, always warnings on the resistance system before disconnect it from the short cables when per- using the resistance system. Use the resist- forming an exercise that does not require it. ance system only as described in this manual. 12. Pull on the low pulley cable
Summary of the content on the page No. 4
BEFORE YOU BEGIN Thank you for selecting the innovative MAX by WEI- manual. To help us assist you, please note the product ® DER ULTRA resistance system. The resistance system model number and serial number before calling. The offers a selection of stations designed to develop every model number is WESY39242. The serial number can major muscle group of the body. Whether your goal is to be found on a decal attached to the resistance system tone your body, build dramatic muscle size and (see the f
Summary of the content on the page No. 5
ASSEMBLY • Tighten all parts as you assemble them, unless Make Things Easier for Yourself instructed to do otherwise. This manual is designed to ensure that the resist- • As you assemble the resistance system, make ance system can be assembled successfully by sure all parts are oriented as shown in the draw- most people. However, it is important to realize ings. that the versatile resistance system has many parts and that the assembly process will take The included Allen wrenches and th
Summary of the content on the page No. 6
2. Attach a Wheel (31) to the outside of the Base (1) 2 with an M10 x 78mm Bolt (81), three M10 Washers (75), and an M10 Nylon Locknut (76). Do not overtighten the Locknut; the Wheel must be able to turn easily. 76 75 Attach the other Wheel (not shown) in the 75 same manner. 81 31 1 3. Orient the Cross Tube (11) as shown, with the 3 welded tubes at the bottom. Attach the Cross 47 3 75 Tube and the Foot Plate (23) to the Upright (3) 23 with two M10 x 140mm Carriage Bolts (73), two M10 Washers (7
Summary of the content on the page No. 7
6. Attach the Lat Tower (4) to the Upright (3) with 6 four M10 x 25mm Button Head Screws (87), and four M10 Lock Washers (68). Attach the Name Plate (89) to the Lat Tower (4) 4 with two M4 x 16mm Screws (62). 68 87 62 87 89 62 68 3 7. Attach two Eyebolts (34) to the Top Frame (10) 7 with two M8 Washers (59) and two M8 Nylon 70 Locknuts (65). Do not overtighten the Locknuts; 65 75 the Eyebolts must be able to rotate freely. 59 93 Attach the Top Frame (10) to the Lat Tower (4) with two M10 x 65mm
Summary of the content on the page No. 8
9. Attach two 8mm Metal Spacers (91), a 60mm 9 Metal Spacer (39), and two Bearing Wheels (46) 12 to one end of the Seat Carriage (12) with an M8 x 60 104mm Button Head Bolt (60) and an M8 Nylon Locknut (65) as shown. Make sure that the parts Attach second set of wheels are oriented as shown in the inset drawing; the here Seat Knob (not shown) will not engage the Bench Rail (not shown) if they are incorrectly 65 oriented. Do not overtighten the Locknut; the 91 Bearing Wheels must be able to roll
Summary of the content on the page No. 9
12. Attach a Plastic Foot (53) to the Backrest Frame 12 (15) with an M4 x 16mm Screw (62). 15 Attach the two Guard Plates (17) to the inside of 53 the Backrest Frame (15) with four M4 x 16mm Screws (62). 62 62 17 62 17 13. Orient the Backrest (14) as shown. Attach the 13 Backrest to the Backrest Frame (15) with four 1/4” x 45mm Screws (58). 14 Insert the rod on the Backrest Frame (15) into the slot in the Seat Carriage (12). Hold the Backrest 15 Frame vertically over the Seat Carriage and slid
Summary of the content on the page No. 10
15. Locate the fulcrum on the Lat Tower (4) (see the 15 86 inset drawing). Slide the Tray (35) onto the rods on the fulcrum. Make sure the Tray is oriented 72 as shown in the drawing. Edges Set the Resistance Bars into the Tray (35) in the Up following order: the 10-pound Resistance Bar (67), the 20-pound Resistance Bar (36), an 80-pound Resistance Bar (95), the 10-pound Center 96 Resistance Bar (44), an 80-pound Resistance Bar 44 (95), and the 40-pound Resistance Bar (96). 4 35 95 Orient the C
Summary of the content on the page No. 11
19. Wrap the Long Cable (80) under a 90mm Pulley 19 (28) as shown. Attach the Pulley and a Cable Trap (29) to the Upright (3) with an M10 x 120mm Button Head Bolt (40) and an M10 Nylon Locknut 3 (76). Make sure the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 28 76 40 80 29 20. Attach a Pulley Housing (94) to the indicated “U”- 20 channel on the 10-pound Center Resistance Bar (44) with an M10 x 102mm Button Head Bolt (24), 44 two Pivot Bushings (74), and an M10 Nylon Loc
Summary of the content on the page No. 12
23. Locate the Leg Lever Cable (32), which has two 23 ends that are the same length and a third end that is longer. Route the longest end of the Leg Lever Cable 6 63 (32) through the hole in the Front Leg (6), and attach it inside of the hole in the Leg Lever (7) with an M10 x 50mm Bolt (63) and an M10 Nylon 32 Locknut (76). 76 7 24. Attach a 90mm Pulley (28) inside of the hole in 24 the Front Leg (6) with an M10 x 91mm Bolt (90), two 26mm Spacers (52), two M10 Washers (75), 5 and an M10 Nylon
Summary of the content on the page No. 13
ADJUSTMENTS This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 17 for important information about how to get the most benefit from your exercise program. Also, refer to the accompa- nying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time the resistance system is used. Replace worn parts immedi- ately. The resistance system can be cleaned with a damp cloth and a mild, non-abrasive detergent.
Summary of the content on the page No. 14
ATTACHING THE ACCESSORIES 33 To attach a Handle (49) to a high pulley, first attach the high pulley to the resistance system (see ATTACHING 51 THE HIGH PULLEYS AND LEG LEVER on page 13). Then, attach the Handle to the Short Cable (33) with a Cable Clip (51). 49 The Ankle Strap (not shown) can be attached to the Long Cable (80) with Cable Clips (51). Attach the Leg Press Strap (not shown) to both ends of the Long Cable, or the optional lat bar to the Short Cables (33), with two Cable Clips. Note
Summary of the content on the page No. 15
ADJUSTING THE BACKREST Rod The Backrest (14) can be used in a level position or 3 15 one of three inclined positions. To use the Backrest in a level position, secure the Seat Carriage (12) to the Slot adjustment hole in the Bench Rail (5) next to the Front Leg (6) (see ADJUSTING THE SEAT on page 13). 14 12 13 To use the Backrest (14) in an inclined position, secure the Seat Carriage (12) to one of the other three adjustment holes in the Bench Rail (5). Rest the Backrest against the Upright (3).
Summary of the content on the page No. 16
CABLE DIAGRAM The cable diagram shows the proper routing of the Long Cable (80). Use the diagram to make sure that Long Cable (80) the Cable has been assembled correctly. If the Cable has not been correctly routed, the resistance system will not function properly and damage may occur. The numbers show the correct route for the Cable. 5 7 4 3 6 2 1 16
Summary of the content on the page No. 17
EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING YOUR EXERCISE PROGRAM Muscle Building Determining the exact length of time for each workout, To increase the size and strength of your muscles, as well as the number of repetitions or sets completed, push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo- cles will continually adapt and grow as you progres- ing it during the first few months of your exercise pro- sively incre
Summary of the content on the page No. 18
Rest for a short period of time after each set. The slowly as you stretch and do not bounce. Ease into ideal resting periods are: each stretch gradually and go only as far as you can • Rest for three minutes after each set for a muscle without strain. Stretching at the end of each workout building workout. is an effective way to increase flexibility. • Rest for one minute after each set for a toning work- out. STAYING MOTIVATED • Rest for 30 seconds after each set for a weight loss workout. For
Summary of the content on the page No. 19
EXERCISE RESISTANCE SETS REPS MONDAY Date: / / AEROBIC EXERCISE TUESDAY Date: / / EXERCISE RESISTANCE SETS REPS WEDNESDAY Date: / / AEROBIC EXERCISE THURSDAY Date: / / EXERCISE RESISTANCE SETS REPS FRIDAY Date: / / Make photocopies of this page for scheduling and recording your workouts. 19
Summary of the content on the page No. 20
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST on the reverse side of this page. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. M6 Nylon Locknut (69) M10 x 53mm Carriage Bolt (61) M8 Nylon Locknut (65) M10 x 50mm Bolt (63) 1/4” x 45mm Screw (58) M8 Flange Nut (19) M10 x 42mm
