Summary of the content on the page No. 1
¨
Model No. 831.150732
Serial No.
USERÕS MANUAL
Write the serial number in the space
above for future reference.
Serial Number Decal (Under Seat)
SEARS, ROEBUCK AND CO.,
HOFFMAN ESTATES, IL 60179
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
www.weiderfitness.com
this equipment. Save this manual
new products, prizes,
for future reference.
fitness tips, and much more!
Summary of the content on the page No. 2
Table of Contents WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 PART IDENTIFICATION CHART . . . . . . .
Summary of the content on the page No. 3
Important Precautions WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the weight bench. 1. Read all instructions in this manual before 12. The weight bench does not include weights. using the weight bench. The weight bench is designed to support a maximum of 360 pounds, including the user, 2. It is the responsibility of the owner to ensure a weight bar, and weights. Do not place more that all users of the weight bench are ade- that 160 pound
Summary of the content on the page No. 4
Before You Begin ¨ Thank you for selecting the WEIDER 500 weight 6879, Monday through Saturday, 7 a.m. until 7 p.m. ¨ bench. The versatile WEIDER 500 weight bench is Central Time (excluding holidays). To help us assist designed to be used with your own weight set (not you, please note the product model number and serial included) to develop every major muscle group of the number before calling. The model number is body. Whether your goal is a shapely figure, dramatic 831.150732. The serial numbe
Summary of the content on the page No. 5
Part Identification Chart This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part, from the PART LIST on page 18. The second number refers to the quantity needed for assembly. Important: Some parts may have been pre-assembled for shipping pur- poses. If you cannot find a part in the parts bags, check to see if it has been pre-assembled. 7mm Spacer (43)Ð1 M10 x 60mm Bolt (18)Ñ1 Pulley Spacer (31)Ð
Summary of the content on the page No. 6
Assembly Before beginning assembly, carefully read the ¥ As you assemble the weight bench, make sure following information and instructions: that all parts are oriented as shown in the draw- ings. ¥ Place all parts of the weight bench in a cleared area and remove the packing materials; do not THE FOLLOWING TOOLS (NOT INCLUDED) dispose of the packing materials until assembly ARE REQUIRED FOR ASSEMBLY: is completed. ¥ Two (2) adjustable wrenches ¥ Read each assembly step before you begin. ¥ One
Summary of the content on the page No. 7
3. Attach the Frame (2) and a Support Plate (40) to 3 the Crossbar (3) with two M8 x 55mm Bolts (41) and two M8 Nylon Locknuts (13). 41 40 13 3 2 4. Press a 25.4mm Round Inner Cap (23) into the 4 end of the Weight Tube (46). 21 Tap 38mm Square Inner Caps (21) into the indi- cated ends of the Leg Lever (4). Note: Only insert 4 the top Inner Cap halfway so that it can be easily removed for storing the curl post. 21 Insert the Weight Tube (46) into the Leg Lever (4) as shown. Press a 25.4mm Angle C
Summary of the content on the page No. 8
7. Press 25.4mm Square Inner Caps (12) into the 7 indicated ends of each Backrest Tube (5). 6 With the help of a second person, slide the indi- cated ends of the Backrest Tubes (5) onto the 12 welded axle on the Frame (2). Attach each Backrest Tube to the Backrest (6) with two M6 x 5 38mm Screws (16) and two M6 Washers (25). The Backrest Tubes must be oriented on the 25 25 outside of the welded axle as shown. Welded 16 16 Axle Do not tighten the four Screws (16) yet. 2 25 16 12 8. Lift the Backr
Summary of the content on the page No. 9
11. Locate the Cable (35) and note that it has a loop 11 on one end and a ball on the other. Slide the loop 21 through the slot in the Lat Tower (27) from the 38 direction shown. Place the Cable (35) in the groove of the Pulley 31 (30). Attach the Pulley inside the slot in the Lat 35 24 Tower (27) with the M10 x 52mm Bolt (38), two M10 Washers (24), two Pulley Spacers (31), and an M10 Nylon Locknut (19). 24 36 Press a 38mm Square Inner Cap (21) into the top 19 of the Lat Tower (27). 30 31 27
Summary of the content on the page No. 10
Using the Weight Bench The weight bench is designed to be used with your own weight set (not included). The steps below explain how the weight bench can be adjusted. See EXERCISE GUIDELINES on page 13 for important exercise information and refer to the accompanying exercise poster to see the correct form for each exercise. Refer also to the exercise information accompanying your weight set (not included) for additional exercises. Inspect and tighten all parts each time you use the weight bench.
Summary of the content on the page No. 11
ATTACHING THE CURL POST OR LAT TOWER Note: When the Curl Post (28) or Lat Tower (27) are not in use, the 38mm Square Inner Cap (21) should be inserted into the Front Leg (8). 28 21 For some exercises, the Curl Post (28) must be attached to the weight bench. 4 Insert the Curl Post (28) into the indicated hole in the Front Leg (8). Align the holes in the Front Leg and the Curl Post. Secure the Curl Post with the Adjustment Knob (39). Make sure that you fully tighten the Adjustment Knob. 27 For ot
Summary of the content on the page No. 12
ATTACHING THE LAT BAR TO THE LAT TOWER To use the Lat Tower (27), attach the Lat Bar (37) to the Cable (35) with a Cable Clip (36). 35 36 37 27 12
Summary of the content on the page No. 13
Exercise Guidelines THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING YOUR EXERCISE PROGRAM Muscle Building We have not specified an exact length of time for In order to increase the size and strength of your each workout, or a specific number of repetitions or muscles, you must push your muscles to a high per- sets for each exercise. It is very important to avoid centage of their capacity. You must also progressively overdoing it during the first few months of your exer- increase the intensity of
Summary of the content on the page No. 14
during the exertion stage of each repetition and inhale strain. Stretching at the end of each workout is very during the return stroke; never hold your breath. Rest effective for increasing flexibility. for 3 minutes after each set if you are doing a muscle building workout, 1 minute after each set if you are STAYING MOTIVATED doing a toning workout, and 30 seconds after each set if you are doing a weight loss workout. Plan to spend For motivation, keep a record of each workout. The the first co
Summary of the content on the page No. 15
EXERCISE WEIGHT SETS REPS MONDAY Date: / / AEROBIC EXERCISE TUESDAY Date: / / EXERCISE WEIGHT SETS REPS WEDNESDAY Date: / / AEROBIC EXERCISE THURSDAY Date: / / EXERCISE WEIGHT SETS REPS FRIDAY Date: / / Make photocopies of this page for scheduling and recording your workouts. 15
Summary of the content on the page No. 16
EXERCISE WEIGHT SETS REPS MONDAY Date: / / AEROBIC EXERCISE TUESDAY Date: / / EXERCISE WEIGHT SETS REPS WEDNESDAY Date: / / AEROBIC EXERCISE THURSDAY Date: / / EXERCISE WEIGHT SETS REPS FRIDAY Date: / / Make photocopies of this page for scheduling and recording your workouts. 16
Summary of the content on the page No. 17
Notes 17
Summary of the content on the page No. 18
R1100A Part ListÑModel No. 831.150732 Key No. Qty. Description Key No. Qty. Description 1 2 Upright 25 4 M6 Washer 2 1 Frame 26 2 M8 x 40mm Carriage Bolt 3 1 Crossbar 27 1 Lat Tower 4 1 Leg Lever 28 1 Curl Post 5 2 Backrest Tube 29 1 Curl Pad 6 1 Backrest 30 1 Pulley 7 1 Support Rod 31 2 Pulley Spacer 8 1 Front Leg 32 2 Carriage Bushing 9 6 19mm Round Inner Cap 33 1 Weight Carriage 10 2 Pad Tube 34 2 Spring Clip 11 1 Seat 35 1 Cable 12 4 25.4mm Square Inner Cap 36 1 Cable Clip 13 10 M8 Nylon Loc
Summary of the content on the page No. 19
R1100A Exploded DrawingÑModel No. 831.150732 44 37Ê 21 35 38 36 24 45 44 13 32 24 19 30 6 31 23 23 33 29 12 25 1 7 16 9 25 5 16 9 25 27 16 25 14 12 16 1 15 15 41 13 40 40 3 28 11 26 13 40 21 13 19 2 21 22 14 22 4 15 18 20 21 17 43 42 39 34 8 13 46 42 42 21 23 13 9 10 9 22 19
Summary of the content on the page No. 20
Model No. 831.150732 ¨ The model number and serial number of your WEIDER 500 are QUESTIONS? listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal. If you find that: All replacement parts are available for immediate purchase or ¥ you need help assembling or ¨ special order when you visit your nearest SEARS Service operating the WEIDER 500 Center. To request service or to order parts by telephone, call the toll-free numbers listed at the lef
