Summary of the content on the page No. 1
TREK INCITE 9i and 11i
Bicycle Computer Owner’s Manual
This manual explains the installa-
tion and use of the Trek Incite 9i
and 11i bicycle computer. Please
read this manual carefully and
save it for future reference.
F
MPH
If you do not understand the
information in this manual, or
you have a question about your
Incite 9i computer that this
CLK TME AVG MAX TRP AVG
manual does not cover, consult
your Trek dealer. If you have a
question or problem that your
Trek dealer can’t handle
Summary of the content on the page No. 2
CONTENTS Safety and general guidelines ..................................................1 Functions ..................................................................................2 Installation ................................................................................4 Placing the computer on the handlebar ..............................5 Placing the magnet ..............................................................7 Attaching the computer wire ...........................
Summary of the content on the page No. 3
SAfETy ANd gENERAl guIdElINES While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the road, you could hit an obstacle, which may cause you to lose control and fall. Make sure the computer wire cannot contact the tire or wheel spokes (Figure 2). The wire could be damaged causing the computer to malfunction. Also, the wire could get caught, causing you to Figure - Watch the road when riding. lose control and fall. Figure 2- K
Summary of the content on the page No. 4
fuNCTIONS Table - Function abbreviations, names, and explanations f unction Explanation CloCK Time of day ClK Displays in hours and minutes, or stopwatch CLK TME showing seconds. 2-hour with AM/PM or 24-hour format Highest reading: 23:59 (clock) or 23:59:59 (stopwatch) oDoMETEr Distance ridden oDo Displays in miles or kilometers. CLK TrP- Trip (since last r estart) MH TME TTl - Total since last r eset AVG MAX Highest reading: 99,999 TR
Summary of the content on the page No. 5
SPEED Always displays Current speed of the bicycle in miles per hour (MH) or kilometers per hour (KMH) AVG- Average speed since last r estart, displayed to tenths. MAX- Highest value since last r estart CLK MH TME Highest readings: 80.5mph or 29.6kph AVG MAX TRP ODO WHEEl Always displays SElECTIon Indicates which wheel setting is in use by computer CLK MH TME AVG MAX TRP ODO Temperature Current temperature displayed in Fahrenheit or Celsius in whole nu
Summary of the content on the page No. 6
INSTAllATION Stem mount Handlebar Speed sensor Cadence sensor mount Figure 3- l ocation on bicycle of sensors and computer Tools needed: • Electrical tape • Slot-type screwdriver • Phillips-type screwdriver • Scissors 4 Installation
Summary of the content on the page No. 7
Placing the computer on the handlebar The Trek Incite 9i or 11i computer can be mounted on the handlebar or on the stem (Figure 3). To install the computer on handlebar 1. Select the bar clamp that fits your bike. 31.8mm bars: large clamp 25.4mm and 26.0mm: small clamp 22.2mm bar: small clamp with rubber shim Figure 4- Clamp and friction pad 2. Insert the handlebar clamp into the back in computer base of the computer base (Figure 4) and slide it towards the front of the base. 3. Insert the
Summary of the content on the page No. 8
Check that the computer base cannot be rotated around the handlebar, and that the computer cannot slide backwards on the computer base (Figure 5). To install the computer on the stem 1. Insert the rubber friction pad into the computer base, aligned along the computer base. Figure 5- Make sure the com- 2. Insert two nylon ties through the puter cannot be bounced off. computer base (Figure 6). 3. Place the base on the stem and tighten the nylon tie. 4. Slide the computer into the computer
Summary of the content on the page No. 9
Placing the magnet The wheel magnet must be aligned so that it passes across the sensor. As the magnet passes the sensor, it must be no further from the sensor than 1 to 3mm (1/32 to 1/8 inch). The wheel magnet has a ‘T’ shaped slot with two configura- tions: round spokes and flat or bladed spokes (Figure 7). To install the wheel magnet 1. Remove the screw from the magnet. 2. Slide the slot in the back of the magnet over the spoke. For a flat or bladed spoke, start the spoke near the end whe
Summary of the content on the page No. 10
Attaching the computer wire The computer wire is usually longer than needed. Extra wire length can be diverted by wrapping it around the brake housing prior to routing it down the fork blade or down tube (Figure 8). Make sure the computer wire is not pulled tight when the handlebar is turned all the way to either side. To attach the computer wire 1. Determine the length of wire to divert by holding the sensor at its desired mounting point. 2. Wrap the wire around the front brake cable, di
Summary of the content on the page No. 11
Attaching the sensors The magnet must pass across the line on the sensor (Figure 9). These instructions are written for the front wheel, but apply equally to installing the magnet and cadence sensor which go on the left crank and the frame’s chainstay (Figure 10). 1.0 - 3.0mm To install the sensor 1. Align the sensor with the magnet. Figure 9- Magnet alignment and 2. Orient the sensor so that the clearance clearance between the sensor and the magnet is between 1 to 3mm. The sensor can b
Summary of the content on the page No. 12
and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is reading the magnet. If the computer is not displaying a value, realign the sensor and magnet until one is displayed. 5. Tighten the nylon ties and trim the excess length (Figure 11). Figure - Trim excess nylon tie length 0 Installation
Summary of the content on the page No. 13
EASy SETuP (RESET) You can program the starting values of your computer in a single, easy procedure: • Units • Clock • Wheelsize • Odometer The Units setting tells the computer which conversion to use: metric or SAE (“English”): MH = miles KMH = kilometers You can set the clock for 12 or 24 hour display, which changes how time appears in the afternoon, such as 3PM: 12 hour clock 3:00 24 hour clock 15:00 You can set the wheel size by simply choosing from a menu listing tire sizes, or yo
Summary of the content on the page No. 14
using the buttons When setting the computer, there are three ways to use the buttons. To help you remember, notice the way F MPH each term is underlined. To help you CLK TME AVG MAX TRP AVG remember, these terms will look the Set same throughout the manual. Push- touch once Cycle - push repeatedly as needed Hold- push and hold in for two or Mode three seconds The buttons on the computer are Figure 2- Buttons on the Incite 9i and i computer (Figure 12): Set• button on the right sid
Summary of the content on the page No. 15
CLK TME MH AVG MAX TRP Set ODO Mode 3. Cycle Mode MH and KMH interchange on the screen. 4. Push Set• to select. The temperature icon display. F MPH 5. Cycle Mode to C or F CLK TME ODO MAX TRP AVG 6. Push Set• to select. The computer returns to the start screen. To set the odometer Figure 3- oDo screen 1. Cycle Mode to ODO (Figure 13). 2. Hold Set• 5-digit odometer value appears with first digit flashing. 3. Cycle Mode to your preferred value. 4. Push Set• to select. The next digit flashes. 5.
Summary of the content on the page No. 16
CLK MH TME AVG MAX TRP Set ODO Mode To set wheel size Both the 9i and 11i allow you to use two different wheel sizes. The icon for Wheel 1 is a small circle. The icon for Wheel 2 is a partial circle surrounding the Wheel 1 icon (Figure 14). 1. Cycle Mode to TME. 2. Hold Set• Wheel Select icon appears on the screen. 3. Cycle Set• to change wheel selection from Wheel 1 to Wheel 2. 4. Push Mode to select. Wheel size appears. Note: If you want to set a custom wheel size, go to page 24 now. Figur
Summary of the content on the page No. 17
CLK TME MH AVG MAX TRP Set ODO Mode To select the wheel for use 1. Cycle Mode to TRP 2. Hold the left Mode and the right Mode together. The Wheel Select icon changes (Figure 14). Repeat step 2 to change again. Easy setup (r eSet) 5
Summary of the content on the page No. 18
CLK MH TME AVG MAX TRP Set ODO Mode To set Clock 1. Cycle Mode to CLK (Figure 15). 2. Hold Set• “12” or “24” flashes. 3. Cycle Mode 12 and 24 interchange on the screen. 4. Push Set• to select The clock appears on the screen with the F MPH Hour flashing. CLK TME AVG MAX TRP AVG 5. Cycle Mode The Hour changes. 6. Push Set• to select. The Minutes flash. Figure 5- CloCK screen 7. Cycle Mode 8. Push Set• to select. The computer returns to current speed. Easy setup (r eSet) 6
Summary of the content on the page No. 19
CLK TME MH AVG MAX TRP Set ODO Mode RESTART- gETTINg REAdy TO RIdE Your computer stores data for two intervals- since last ReSet and since last ReStart. ReSet sets ALL data to zero. ReStart sets only the Trip data to zero. The trip modes include • TRP • TME • MAX This operation sets all four values to zero, allowing the computer to display information for a single ride. To ReStart (set the Trip data to zero) 1. Cycle Mode to TRP (Figure 16). 2. Hold Set•, and do not let up until after com
Summary of the content on the page No. 20
CLK MH TME AVG MAX TRP Set ODO Mode AddITIONAl INf ORMATION Changing mode Once the computer is programmed and installed, it is very easy to use. To change to different modes (functions), simply Cycle the Mode button until the desired function appears, shown by the spelled name of the function. Removing the computer from the computer base The computer is held on its base by a flexible snap. To remove the computer, press firmly on the computer (not on the base) in a rearward direction. using
