Snapper 2365 user manual

Summary of the content on the page No. 1

Attachment
Illustrated
Parts List
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Rev. 8/2000
Port Washington, WI 53074-0997 USA
TP 400-2365-00-AT-SMA
© Copyright 2000 Simplicity Manufacturing, Inc.All Rights Reserved.

Summary of the content on the page No. 2

Hydraulic Angling & Lift Group 60” Dozer Blade 985457 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 21 16 1 7 7 6 17 20 18 5 3 5 4 19 5 3 2 17 26 16 9 29 8 5 28 27 22 7 23 26 25 24 10 5 11 5 8 5 5 8 40 39 5 12 5 31 12 5 30 13 5 38 5 36 5 32 5 37 5 15 5 36 5 33 5 15 10 5 5 34 5 35 5 14 5 The above parts group applies to the following Mfg. Nos.: 1693274 Hydraulic Angling & Lift Kit © Copyright 2000 Simplicity Manufacturing, Inc. All Rights Reserved. TP 400-236

Summary of the content on the page No. 3

Hydraulic Angling & Lift Group 60” Dozer Blade REF NO. PART NO. QTY. DESCRIPTION 1 1701011 3 TIE, Self Locking 2 1960277 1 PIN, Yoke 3 1918452 3 PIN, Cotter 4 1677214 1 ANGLING CYLINDER ASSEMBLY 5 1700394 1 PIN, Flat Head, 5/8 x 1-5/8 6 919171 2 FITTING 7 173359 4 NOSE PIECE ASSEMBLY 8 1719395 2 HOSE ASSEMBLY 9 1719565 2 HOSE ASSEMBLY 10 1719586 1 HOSE SUPPORT 11 1931277 2 NUT, Hex, 5/16-18 12 919171 4 TUBE FITTING, Male 13 1716944 1 LIFT CYLINDER ASSEMBLY 14 1711773 2 PIN, Clevis 15 176012 2 PI

Summary of the content on the page No. 4

OUT IN DECAL Hydraulic Angling & Lift Group 60” Dozer Blade 985457 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 44 43 42 58 41 45 Attachment Attachment 8 Angling 46 Hose Support 57 Cylinder 10 9 56 47 48 Lift 48 Cylinder To "IN" Port of Tractor Lift Valve 49 59 66 Diesel Front of Gas Models 65 Models Tractor 55 To "E" Port of 64 Steering Valve 50 63 Hose 51 Clamp “T” 62 Connector 28 27 42 Hydro Pump Hose 28 Clamp 51 27 52 41 26 60 54 61 27 53 28 The a

Summary of the content on the page No. 5

Hydraulic Angling & Lift Group 60” Dozer Blade REF NO. PART NO. QTY. DESCRIPTION 46 1719580 1 MOUNTING PLATE 47 1923282 1 CAPSCREW, Hex Head,1/4-20 x 2-1/2 48 1960234 2 SPACER 49 1718419 1 VALVE ASSEMBLY 50 1718988 1 PLATE 51 1673796 3 SPACER 52 1917356 2 LOCKWASHER, 5/16 53 1917372 2 NUT, Hex 5/16 54 1718991 1 VALVE SUPPORT ASSEMBLY 55 1931337 2 CARRIGE BOLT, 5/16-18 x 1-1/2 56 960603 1 CAPSCREW, Hex Head,1/4-20 x 3-1/2 57 1719393 1 POD, Seat Deck 58 1719733 1 DECAL, Hydraulic Levers 59 1719331

Summary of the content on the page No. 6

0 1 2 3 4 1/2 1/2 1/2 1/2 1/4 3/4 1/4 3/4 1/4 3/4 1/4 3/4 Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer No Hardware Lockwasher Marks Grade Carriage Bolt SAE Grade 2 SAE Grade 5 SAE Grade 8 Hex Nut Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. Standard Hardware Sizing 8-32 19 2.1 30 3.4 41 4.6 When a washer or nut is identified as 1/2”, this is the