Summary of the content on the page No. 1
CVC10SS
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Summary of the content on the page No. 2
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel. Appliance information: Please enter the details on the appliance rating plat
Summary of the content on the page No. 3
Coffee machine COFFEE MAKER CVC10 CONTROL PANEL 1 2 3 4 5 1 - Display 2 - Control panel 3 - Dispenser spout 4 - Steam nozzle 5 - Drip tray drawer Control panel COFFEE MAKER CVC10 CONTROL PANEL 1 2 3 4 5 6 1. Power Button – Press to turn the machine on and off. (Standby) 2. Number Cups – Press to select between 1 and 2 cups. 3. Coffee Size Button – Press to select between short, medium and long options. 4. Make Coffee Button – Press to begin the coffee making process. 5. Steam – Press
Summary of the content on the page No. 4
First use This coffee machine has two water heaters, one for the water and one for the coffee, which allows for ideal temperatures for coffee and steam for cappuccino. The steam can also be used to preheat the cups. This coffee machine can grind coffee beans when they are needed, ensuring they are freshly ground for the very best flavour. To stop the coffee machine dispensing – if less than the preset amount is required – simply press at any point when the coffee is dispensing. The grinding
Summary of the content on the page No. 5
To fill the coffee container: 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Remove the lid of the coffee container and fill it until the coffee beans are 2cm from the top level. Then replace the lid. 3. Push the machine back into the housing. Setting/Adjusting the grind 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Carefully turn the control knob located on the left s
Summary of the content on the page No. 6
The Coffee Machine Press to switch on the coffee machine After a few seconds, GOOD MORNING will show on the display. The machine will heat up, and COFFEE and STEAM will flash on the display. Once the machine is ready for use, COFFEE and STEAM will illuminate constantly, as will the size and number of the coffees last selected (for example 1 SHORT). If COFFEE continues to flash, add coffee beans to the container. If STEAM continues to flash (non-mains plumbed coffee machines only) add water
Summary of the content on the page No. 7
5. Make a cappuccino We recommend preparing cappuccinos individually so as to ensure best flavour. 1. Make a medium espresso as described above in a large cup. 2. Press to select steam and wait until STEAM stops flashing. 3. Before putting the container under the steam nozzle, press and hold for approximately five seconds, to flush out any water remaining in the pipes. 4. Fill a 50cl stainless steel container with 10cl milk. 5. Put the steam nozzle into the container so it is at the bot
Summary of the content on the page No. 8
Programming The coffee machine is equipped with a programming mode to enable you to set the following as required: To enter programming mode follow the steps below: 1 Whilst the machine is off, press and hold until PROGRAMMING shows on the display 2. Press or until the required programme shows on the display. 3. To change the setting, press or until the required setting shows on the display. 4. Press to exit programming mode. Programming options are:
Summary of the content on the page No. 9
Care and Maintenance DO NOT PERFORM ANY MAINTENANCE OR CLEANING WITHOUT FIRST SWITCHING OFF THE POWER SUPPLY. THE COFFEE MACHINE WILL BE HOT IMMEDIATELY AFTER USE. ALLOW IT TO COOL BEFORE CLEANING. As the coffee machine has a stainless steel and glass surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water a
Summary of the content on the page No. 10
Care and Maintenance Descaling If the display shows DESCALING then the coffee machine needs to be descaled to ensure best performance. Please note: You should use cleaning products that are appropriate for use with coffee machines. Do not use lemon-based products to descale the coffee machine as these can cause irreparable damage to the coffee machine. Failure to descale your coffee machine constitutes misuse and may invalidate your guarantee. To descale the coffee machine, follow the steps be
Summary of the content on the page No. 11
Troubleshooting The coffee machine does not The machine is not fully back in its Push the coffee machine back switch on. housing. fully. There is a problem with the electricity Check that the mains supply supply. has not been switched off. Check that the fuse in the spur has not blown. The coffee will not dispense or The coffee grind is too fine. Adjust the grind to be coarser. dispenses only in slow drips. There is not enough water in the water Fill the water tank or check tank. there is no
Summary of the content on the page No. 12
Installation IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY SUITABLY QUALIFIED PERSON. 542 1. Slide the base unit into the housing ensuring the dimensions are 320 min correct as per figure 1. 2. Fix the base unit in place by attaching the 10 screws in to 320 the holes as shown in figure 2 and figure 3. If the sides of the fig. 1 base are not flush with the sides of the housing, then use the shims provided. 3. Push the runners fully closed on the base unit. 4. Conn
Summary of the content on the page No. 13
Installation Please note: Due to the weight of this appliance, the furniture unit must be secured to the wall prior to installation. You must ensure that all water connections are sound and check there are no leaks before completing installation. For best performance, the mains water pressure must be between 0.1 - 3 bar. fig. 4
Do not use outdoors. To reduce the risk of electric shock, do not mount over a sink. The water supply should be located in a place that allows the machine to be iso
Summary of the content on the page No. 14
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable f
Summary of the content on the page No. 15
14
Summary of the content on the page No. 16
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
