Summary of the content on the page No. 1
848-C3A-93A0 (410)
OWNER/OPERATOR MANUAL
CHAINSAWS
G3200
G3200EZ
WARNING WARNING
The engine exhaust from this product Before using our products, please
contains chemicals known to the State read this manual carefully to
of California to cause cancer, birth understand the proper use of your
defects or other reproductive harm. unit.
APPLICABLE SERIAL NUMBERS :
G3200 : 404766 and up G3200EZ : 400001 and up
Summary of the content on the page No. 2
Summary of the content on the page No. 3
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL WARNING This mark indicates instructions which must be followed in order to prevent accidents which could lead to serious bodily injury or death. IMPORTANT This mark indicat
Summary of the content on the page No. 4
1. Parts location 1. Front guard 2. Starter knob 3. Air cleaner 4. Choke knob 5. Throttle interlock 6. Right handle 7. Throttle lever 8. Engine switch 9. Fuel tank 10. Oil tank 11. Left handle 12. Saw chain 13. Guide Bar 2. Specifications ■ G3200 / G3200EZ Power unit : 3 Displacement ···················································································· 2.00(31.8) cu-in(cm ) Fuel ············································································ Mixture (Gasoline 50 : 2-
Summary of the content on the page No. 5
3. Symbols on the machine WARNING For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the "MIX GASOLINE" Position: Fuel cap (b). The port to refuel the chain oil Position: Oil cap (c). Put the switch to the "O" position, immediately the engine stops. Position: Rear-left of the unit (d). If you pull out the choke knob, you can set the choke as a cold start mode.
Summary of the content on the page No. 6
4. For safe operation 1. Never operate a chain saw when you are 9. Before you start the engine, make sure fatigued, ill, or upset, or under the the saw chain is not contacting anything. influence of medication that may make 10. Always carry the chain saw with the you drowsy, or if you are under the engine stopped, the guide bar and saw influence of alcohol or drugs. chain to the rear, and the muffler away 2. Use safety footwear, snug fitting clothing from your body. and eye, hearing and head
Summary of the content on the page No. 7
4. For safe operation 17. Operate the chain saw only in well 20. When transporting your chain saw, make ventilated areas. Never start or run the sure the appropriate guide bar scabbard engine inside a closed room or building. is in place. Exhaust fumes contain dangerous 21. This chain saw is equipped with a spark carbon monoxide. arrester built-in muffler. Periodically 18. Do not operate a chain saw in a tree check the arrester to keep it in good unless specially trained to do so. order. 19.
Summary of the content on the page No. 8
5. Installing guide bar and saw chain A standard saw unit package contains the items as F5-1 illustrated. (1) Power unit (2) Bar protector (3) Guide bar (4) Saw chain (5) Plug wrench Open the box and install the guide bar and the saw chain on the power unit as follows: WARNING The saw chain has very sharp edges. Use thick protective gloves for safety. [G3200] 1. Pull the guard towards the front handle to check that the chain brake is not engaged. 2. Loosen the nut and remove the chain cover.
Summary of the content on the page No. 9
5. Installing guide bar and saw chain NOTE A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar. [G3200EZ] 1. Pull the guard towards the front handle to check F5-4 that the chain brake is not engageg. 2. Loosen the nut assembly and dismount the (1) chain cover. (1) Nut assembly (2) Chain cover (3) Loosen (2) (3) 3. Set the guide bar to the power unit, gear the chai
Summary of the content on the page No. 10
5. Installing guide bar and saw chain IMPORTANT While temporary tightening, you may hear the “click” sound. But do not stop tightening at that time. This sound does not mean that the saw chain and guide bar were assembled. F5-7 (3) 5. While holding the chain cover, temporary tighten the nut assembly and fix the bar and chain cover. (You can fix them even by tightening the lever.) Check if the saw chain fits on the bar rail. If not, (1) (2) readjust by loosen the nut assembly. (1) Nut assembly (2
Summary of the content on the page No. 11
6. Fuel and Chain oil ■ RECOMMENDED MIXING RATIO WARNING GASOLINE 50:OIL 1 • Gasoline is very flammable. Avoid 50:1 MIXING CHART smoking or bringing any flame or GASOLINE gal. 1 2 3 4 5 sparks near fuel. Make sure to stop the 2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13 engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least GASOLINE liter 1 2 3 4 5 3m (10ft) away from the fueling point 2-CYCLE OIL ml 20 40 60 80 100 before starting the eng
Summary of the content on the page No. 12
6. Fuel and Chain oil again for at least one minute. As some 5. In the case of storing the product for a oils may be difficult to agitate depending long period of time, clean the fuel tank on oil ingredients, sufficient agitation is after rendering it empty. Next, activate the necessary for the engine to last long. Be engine and empty the carburetor of the careful that, if the agitation is insufficient, composite fuel. there is an increased danger of early 6. In the case of scrapping the used mi
Summary of the content on the page No. 13
7. Operation WARNING It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the F7-1 parts including bar and chain are installed properly. (1) ■ STARTING THE ENGINE (2) 1. Fill fuel and chain oil tanks respectively, and tighten the caps securely. (1) Fuel (2) Chain oil F7-2 (1) 2. Set the switch to “I” position. (1) Switch 3. Continuously push the priming bulb until fuel F7-3 comes in the bulb. (1) (1) Priming bul
Summary of the content on the page No. 14
7. Operation 6. When engine has ignited, pull the throttle slightly to return the choke knob to the original position. If the engine stops, pull the starter again without pulling out the choke knob. 7. Allow the engine to warm up with the throttle lever pulled slightly. WARNING Keep clear of the saw chain as it will start rotatIng upon starting of engine. ■ CHECKING THE OIL SUPPLY WARNING Make sure to set up the bar and the chain when checking the oil supply. If not, the rotating parts may be e
Summary of the content on the page No. 15
7. Operation 1. H and L needles are restricted within the number F7-8 of turn as shown below. (2) (3) (1) H needle –1/4 L needle –1/4 2. Start engine and allow it to warm up in low speed for a few minutes. 3. Turn idle adjusting screw (T) counter-clockwise so that saw chain does not turn. If idling speed is too slow, turn the screw clockwise. 4. Make a test cut adjust the H needle for best cutting power, not for maximum speed. (1) L needle (2) H needle (3) Idle adjusting screw
Summary of the content on the page No. 16
7. Operation When the brake engages during operation, immediately release the throttle lever to stop the engine. F7-11 ■ STOPPING THE ENGINE (1) 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. (1) Switch ■ CARBURETOR ANTI-FREEZE MECHANISM Operating chain saws in temperatures of 0 – 5°C at times of high humidity may result in ice forming within the carburetor, and this in turn may cause the output power of the engine t
Summary of the content on the page No. 17
8. Sawing WARNING • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. •Always follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vibrations and kickback vary with different materials and the requirements of the safety regulations would not be respected. Do not use the chain saw as a lever for lifting,
Summary of the content on the page No. 18
8. Sawing ■ FELLING A TREE (F8-2) 1. Decide the felling direction considering the wind, lean of the tree, location of heavy F8-2 branches, ease of job after felling and other factors. 2. While clearing the area around the tree, arrange a good foothold and retreat path. 3. Make a notch cut one-third of the way into the tree on the felling side. 4. Make a felling cut from the opposite side of the notch and at a level slightly higher than the bottom of the notch. WARNING When you fell a tree,
Summary of the content on the page No. 19
8. Sawing A Log lying on the ground (F8-3) F8-3 Saw down halfway, then roll the log over and cut from the opposite side. A Log hanging off the ground (F8-4) F8-4 In area A, saw up from the bottom one-third and finish by sawing down from the top. In area B, saw down from the top one-third and finish by sawing up from the bottom. Cutting Limb of Fallen Tree (F8-5) F8-5 First check to which side the limb is bent. Then make the initial cut from the bent side and finish by sawing from the opposi
Summary of the content on the page No. 20
9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING Before cleaning, the inspecting or repairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. F9-1 (1) ■ MAINTENANCE AFTER EACH USE 1. Oiling port Dismount the guide bar and check the oiling port for clogging. (1) Oiling port 2. Guide bar When the gui
