Summary of the content on the page No. 1
NOTE: The E100/E125/E150/E175 must be traveling up to 3mph before motor will
engage. Kick start up to 3mph while applying the throttle to engage motor.
Owner’s Manu
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
Item Number:
E100 Red 13111260
E100 Pink 13111261
E100 Daisy 131
Summary of the content on the page No. 2
CONTENTS Safety Warnings ............................................................ 1 Repair and Maintenance ............................................. 4-6 Before You Begin ........................................................... 2 Troubleshooting Guide ................................................ 7-8 Assembly and Set-Up .................................................... 3 Electric Scooter Parts .................................................... 9 Hardware Maintenance .........
Summary of the content on the page No. 3
BEfORE yOU BEGIN Remove contents from box. Remove the foam separators that protect the components from damage during WARNING: shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have DO NOT USE NON- occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there RAZOR PRODUCTS should not be any problems, even if the box has a few scars or dents. WITH YOUR RAZOR ELECTRIC SCOOTER. MAKE SURE P
Summary of the content on the page No. 4
ASSEMBLy AND SET-UP Note: Make sure the cables/ q Attaching the Handlebars wires are out of the way before inserting the stem into the fork. (a) 1 Open the quick release. 2 Depress the push button (a) 3 Adjust the tension of the located on the front fork and quick release to where you can insert the handlebar stem until close the lever all the way to the button locks securely into secure the stem. the fork. Note: The pressurized air q Inflating the Tire supplies found at gasoline The f
Summary of the content on the page No. 5
CONNECTORS/HARDWARE MAINTENANCE Brake Safety Gear Check the brakes for proper function. When you squeeze the lever, Always wear proper protective gear such as an approved safety q q the brake should provide positive braking action. When you apply helmet. Elbow pads and kneepads are recommended. Always the brake with the speed control on, the brake cut-off switch wear athletic shoes (lace-up shoes with rubber soles), never ride should stop the motor. Make sure that brakes are not rubbing. b
Summary of the content on the page No. 6
REPAIR AND MAINTENANCE Note: Front wheel hardware q front Wheel Replacement sequence Tools required: 10mm wrench, two (2) 17mm wrenches and a flathead screwdriver. 8-1 8-3 8-2 8-2 8-6 8-5 8-1 8-2 8-2 Right Side (Throttle) 8-3 - (Short) spacer 1 Using a 10mm open wrench, 2 Using two 17mm wrenches, 8-2 - Washer loosen the brake cable bolt. loosen the locknuts by turn- ing the wrenches counter Fork clockwise. Remove wheel and 8-2 - Washer install replacement wheel. 8-1 - 17mm locknut Middle 8-
Summary of the content on the page No. 7
REPAIR AND MAINTENANCE q Battery Care and Disposal WARNING: If a battery Do not store the battery in temperatures above 75° or below -10° F. leak develops, avoid contact with the leaking acid and place the CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED. damaged battery in a plastic bag. Refer to the disposal instructions at Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an left. If acid comes
Summary of the content on the page No. 8
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Scooter does not run Scooter must be traveling 3mph Kick start to 3mph while twisting the throttle to engage motor. before motor will engage. Battery needs a charge Charge the battery. A new battery should be charged for at least 18 hours before using the scooter for the first time and up to 12 hours after each subsequent use. Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and that t
Summary of the content on the page No. 9
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Check all wires around the motors and all connectors to make sure Sometimes the scooter Loose wires or connectors they are tight. doesn’t run, but other times it does Motor or electrical switch Contact your local Razor authorized service center for diagnosis and repair. damage TM TM Chain is too dry Apply a lubricant such as 3 in 1 or Tri-Flow to the chain. Scooter makes loud noises or grinding sounds For more helpful troubleshootin
Summary of the content on the page No. 10
E100/E125/E150/E175 PARTS Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 11 On/ Off switch 01 Handlebar grip (right/left) 02 Single speed twist grip throttle 12 Charger port 13 Reset button 02-1 Sleeve 14 Control module 03 Handlebar stem 04 Brake lever assembly 15 Battery (2- 12V/ 4.5Ah) 16 Kickstand 05 Quick release lever 17 Motor (24V
Summary of the content on the page No. 11
SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT. 10
Summary of the content on the page No. 12
WARRANTy Razor does not offer an extended warranty. If you have purchased an Razor Limited Warranty extended warranty, it must be honored by the store at which it was The manufacturer warranties this product to be free of manufacturing defects purchased. for a period of 90 days from date of purchase. This Limited Warranty does not cover normal wear and tear, tires, tubes or cables, or any damage, failure For your records, save your original sales receipt with this manual and write or los
