Summary of the content on the page No. 1
Owner’s Manual
read and understand this entire manual before riding!
DO nOT reTurn TO sTOre!
nOTe: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
specifications subject to change without notice.
Item Numbers:
Dirt rocket MX500 15128190
Dirt rocket MX650 15165070
Version 1_04/11
Summary of the content on the page No. 2
cOnTenTs Safety Warnings .................................................................................1 Troubleshooting Guide ........................................................................9 Before You Begin .................................................................................2 MX500 / MX650 Parts ......................................................................10 Assembly and Set-Up ...................................................................... 3-5 Safety
Summary of the content on the page No. 3
BefOre yOu BegIn Remove contents from box. Remove the foam separators that protect the components from damage during warnIng: shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have DO NOT USE NON-RAZOR occurred during shipping. Because the Dirt Rocket is 95 percent assembled and packed at the factory, there PRODUCTS WITH YOUR RAZOR should not be any problems, even if the box has a few scars or dents. DIRT ROCKET. The Dirt Rocket
Summary of the content on the page No. 4
asseMBly anD seT -up attaching the Handlebars 3 Adjust the brake lever 1 Place the handlebars in 2 Align parallel to the fork and adjuster to the proper place the handlebar clamps. tighten the bolts using a 6mm and tighten it with the 5mm Allen wrench. When properly Allen wrench. Note: Handlebar clamps are tightened, the handlebars should located in the plastic bag. not move forward or back. q attaching the front fender 1 Align fender with the hole in the fork and insert the bolt. Ti
Summary of the content on the page No. 5
asseMBly anD seT -up Installing the front wheel warnIng: Failing to properly adjust and tighten the nuts and bolts that affix the fork can cause you to lose control and fall. 1 Position wheel in front fork 2 Slide axle through fork, spacer and wheel hub. When axle passes and slide disk brake into caliper. through the other side of the wheel hub, add the other spacer and slide though the fork. Secure with washer and nut. Note: Front axle is installed with the spacer between the f
Summary of the content on the page No. 6
BefOre rIDIng charging the Battery Your electric motorbike may not have a fully charged battery; therefore it is a good idea to charge the warnIng: battery prior to use. Always disconnect your electric motorbike from the charger before • Initial charge time: 12 hours • Run time: Up to 40 minutes of continuous ride time cleaning with liquid. • Recharge time: up to 12 hours, Run time may vary depending on riding conditions, depending on level of depletion. climate and/or proper m
Summary of the content on the page No. 7
repaIr anD MaInTenance Turn power switch “OFF” before conducting any maintenance procedures. q chain and Tire replacement 16-1 16-2 Tools required: Phillips screwdriver and two (2) 19mm open wrenches. 16-3 16-3 16-2 16-1 Note: the arrangement of the hardware sequence: 1 Loosen screw and remove 2 Using two 19mm wrenches, 3 Push the chain tensioner Right Side (Throttle) chain guard. loosen both axle nuts. down to loosen the chain and remove the chain from the 16-1 Nut wheel sprocket an
Summary of the content on the page No. 8
repaIr anD MaInTenance qchecking spoke Tension Spoke 27 warnIng: Flange Regularly check the spoke 28 tension and retighten the Hub Spoke spokes whenever loose. If Flange you have any doubt, ask an 1 2 4 3 experienced motorcycle or Spoke bicycle mechanic to inspect Flange your spokes to determine if Rim Nipple the spokes need tightening or Nipple adjusting. 1 Verify the spoke tension by shaking each spoke with your fingers. 2 Start with spoke closest to the Spoke should not be l
Summary of the content on the page No. 9
r rep epa aI Ir an r anD D Ma MaI In nT Tenance enance q Battery care and Disposal warnIng: Do not store the battery in temperatures above 75° F or below -10° F. If a battery leak develops, avoid contact with the leaking acid CONTAINS SEALED NON-SPILLABLE LEAD BATTERIES. BATTERIES MUST BE RECYCLED. and place the damaged battery in a plastic bag. Refer to the Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or dispos
Summary of the content on the page No. 10
TrOuBlesHOOTIng guIDe problem possible cause solution Undercharged battery Motor bike does not run Charge the battery. A new battery should have been charged for at least 12 hours before using the motor bike for the first time and up to 12 hours after each subsequent use. Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and that the charger is plugged into the wall. Make sure power flow to the wall outlet is on. Loose wires or connectors Chec
Summary of the content on the page No. 11
MX500 / MX650 par Ts Keep your MX500/MX650 running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 15 Kickstand 01 Handlebar grip (right/left) 08 Handlebar clamp (upper/lower) 09 Front wheel complete 16 Rear wheel complete 02 Twist grip throttle 17 Chain 10 Caliper brake 02-1 Sleeve 18 Chain guard 03 Front brake lever assembly (right) 11 Shock 12 Control module 19 Battery co
Summary of the content on the page No. 12
SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT. 11
Summary of the content on the page No. 13
safeTy reMInDers pre-rIDe cHecKlIsT loose parts Tire Inflation There should not be any unusual rattles or sounds from Periodically inspect the tires for excess wear and replace as q q loose parts or broken components. If you are not sure, ask required, and regularly check the tire pressure and re-inflate an experienced mechanic to check. as necessary. If you get a flat tire, the inner tube can be patched or a new tube can be purchased from Razor or an authorized repair center. Brakes Chec
