Summary of the content on the page No. 1
Operation
Operation TOASTER
TOASTER
TX-208
TX-208
Manual
Manual
LIMITED WARRANTY TABLE OF CONTENTS
This product is warranted to be free from defects in material and/or work-
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
manship for a period of two (2) years from date of original installation. One
(1) year on-site with the exception of conveyor belts and Teflon sheets
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . .2
(they are subject t
Summary of the content on the page No. 2
TOASTER TX-208 Safety Information Electrical Specifications Model No. Volts Watts Amps Hz WARNING Indicates information important to the proper opera- TX-208 208 4000 19.2 60 tion of the unit. Failure to observe may result in dam- age to the equipment and/or severe bodily injury or death. CAUTION Indicates information important to the operation of the unit. Failure to observe may result in damage to the equipment. Product Identification Conveyor Belt (under cover) Lower Retaining Bar Upper R
Summary of the content on the page No. 3
TOASTER TX-208 Operation Press the On/Off Button to turn the unit on. Feed the buns into the bun chute, flat (toasted) side up. 1 3 The conveyor will begin to turn and the display will read “L LO O”. When the unit is at operating temperature the display will R R D D Y Y R RD DY Y read “ ” and the ACT (actual Bun Chute temperature) LED will be lit. Temperature LED’s Display Power On/Off Button Press the On/Off Button to turn the unit off. Turn the Bun Thickness Adjustment Knobs to the desired set
Summary of the content on the page No. 4
TOASTER TX-208 Daily Cleaning WARNING Remove the lower retaining bar from the release sheet and pull 3 Before performing any maintenance, press the power switch to the the release sheet up thru the top of the unit. Remove the upper OFF position. If the heater is above 450°F, the display will alternately retaining bar from the release sheet. show “C CO OO OL L” and “O OF FF F”, and the conveyor belt will continue to run approximately 45 minutes. When the unit has cooled sufficiently, the display
Summary of the content on the page No. 5
TOASTER TX-208 Remove the plastic spline from the belt. Release the upper and lower locking latches from the conveyor 6 8 rollers. Upper Latch Place the belt (orange surface up) on a flat surface. Clean the belt orange surface with a mild dishwashing detergent (CAPITAL 9 used to clean trays works well. Mix 1 part CAPITAL to 9 parts water). Spray detergent onto orange portion of belt, then wait 1 minute for residue to dissolve. Spray detergent onto a no-scratch pad and wipe the belt to remove
Summary of the content on the page No. 6
TOASTER TX-208 Programming To view the setpoint temperature, press and release the SET Control Panel 3 Button. The setpoint LED will glow and the setpoint will be displayed for 5 seconds, then change back to R RD DY Y. Actual Temperature LED Display Setpoint LED Program LED 4 0 R D Y 5 Set Button Scan Up/Actual Temp Button Scan Down Button Power On/Off Button To switch from Fahrenheit to To change the setpoint temperature, press and hold the SET Celsius, turn the unit off. Press and Temperature
Summary of the content on the page No. 7
TOASTER TX-208 Troubleshooting Problem Possible Cause Corrective Action No power to unit. Make sure power cord plugged into the unit and Unit will not heat up. proper electrical receptacle. Inoperable power cord. Replace power cord. Tighten power switch connections. Loose connection on power switch. Inoperable power switch. Replace power switch. High limit switch tripped. Reset limit switch. Using a pencil or pen, press the hollow portion of the 3/8" long brown, plastic stem located at the right
Summary of the content on the page No. 8
TOASTER TX-208 Parts List & Exploded View 27 28 26 29 47 16 17 19 25 15 18 20 23 45 46 35 36 21 34 14 37 32 13 11 12 38 42 24 22 10 9 8 41 7 39 44 43 3 40 33 6 2 15 30 4 1 5 Ref. Part No. Description Ref. Part No. Description 25 537-295S Platen 1 537-324 Front Cover 26 537-337 Insulation 2 537-618 Bun Chute 27 537-296 Heater Housing 3 537-725S Rubber Belt 28 537-366 Heater Housing Plate 4 537-330S Conveyor Assy. 29 537-409 Rear Panel 5 537-338 Base Pad 30 537-332 RH Cover 6 537-320 B
Summary of the content on the page No. 9
TOASTER TX-208 Parts List & Exploded View 15 12 10 1 11 13 17 9 14 16 5 3 7 2 6 8 4 Ref. Part No. Description Ref. Part No. Description 10 537-411 Upper Roller 1 537-351 Frame 11 537-315 Upper Shaft 2 537-354 Air Shield 12 537-317S Upper Bearing (Package of 2) 3 537-349 Cross Brace 13 79-055S Washer (Package of 2) 4 537-412 Lower Roller 14 81-017S Spring (Package of 2) 5 537-370S Lower Bearing (Package of 2) 15 86-272S Cotter Pin (Package of 2) 6 537-318S Lower Shaft (Short) 16 69-011S Rivet (Pa
Summary of the content on the page No. 10
TOASTER TX-208 Wiring Diagram TRANSFORMER PLATEN HEATER RELAY RED VIO WHT YEL BLK POWER NC C NO BLK BLK RELAY RED YEL BLK NOT USED HI-LIMIT THERMOSTAT POWER TERMINAL BLOCK 12 11 ORG WHT ORG DISTRIBUTION BLK TERMINAL BLOCK POWER CORD TEMPERATURE WHT J14 J7 SENSOR WHT OPTIONAL FUSE BLOCK SEE CONNECTION DETAIL CONTROL FOR USAGE BOARD RED PLATEN HEATER WHT BLK WHT AUXILIARY HEATER J1 3A FUSE BLOCK 240V 200V CONNECT WHITE WIRE CONNECTION DETAIL TO PROPER MOTOR USED ONLY ON VOLTAGE TAB YEL TX-208 & T
