Poulan 96192002901 user manual

User manual for the device Poulan 96192002901

Device: Poulan 96192002901
Category: Snow Blower
Manufacturer: Poulan
Size: 1.47 MB
Added : 2/28/2014
Number of pages: 40
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Poulan 96192002901. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Poulan 96192002901.

For your convenience

If looking through the Poulan 96192002901 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Poulan 96192002901 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Poulan 96192002901 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Poulan 96192002901 User manual - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Poulan 96192002901 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Poulan 96192002901. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

IMPORTANT MANUAL Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
PR624ES
In struc tions. Fail ure to do so
can result in serious injury.
SNOW THROWER
428689 Rev. 2 09.23.09 AP
Always Wear Eye Protection During Operation
Printed in the U.S.A.

Summary of the content on the page No. 2

IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA

Summary of the content on the page No. 3

6. When cleaning, repairing or inspecting the snow thrower, 16. Never touch a hot engine or muffler. stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect Clearing a Clogged Discharge Chute the spark plug wire and keep the wire away from the Hand contact with the rotating impeller inside the discharge plug to prevent someone from accidentally starting the chute is the most common cause of injury associated with engine. snow throwers. Never u

Summary of the content on the page No. 4

PARTS PACKED SEPARATELY IN CARTON (1) AUGER CONTROL ROD (1) MULTI- WRENCH (180684) (3) RETAINER SPRINGS (2) FLAT WASHERS (169675) (1) POWER CORD (198563) (1) DISCHARGE CHUTE ROTATOR HEAD MOUNTING (2) CARRIAGE BOLTS 3/8-16 x 2.25 (2) SAFTEY IGNITION KEY (422663) (1) WASHER 3/8 (1) LOCKNUT 3/8 (19131316) (73800600) (2) HANDLE KNOBS EXTRA SHEAR BOLTS AND NUTS (2) SHEAR BOLTS 1/4-20 x 1-3/4 (2) LOCKNUTS (192090) 1/4-20 (73800400) ASSEMBLY / PRE-OPERATION Read these instructions and this manual in

Summary of the content on the page No. 5

ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the INSTALL TRACTION DRIVE CONTROL ROD chute rotator head to snow thrower and making ad just ments (See Figs. 3 and 4) to the skid plates. The traction drive control rod is installed on the snow UNFOLD UPPER HANDLE thrower. 1. Raise upper handle to the operating position and 1. Remove plastic tie securring rod to lower handle. tight en handle knobs securely. Additional carriage 2. With top end of rod positioned und

Summary of the content on the page No. 6

ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) HEAD (See Fig. 7) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. NOTE: The multi-wrench provided in your parts bag may Slide straight rod end through the small hole in the be used to install the chute rotator head. vinyl sleeve. Hook spring in hole in rod end. 1. Place discharge chute assembly on top of chute base

Summary of the content on the page No. 7

OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR

Summary of the content on the page No. 8

OPERATION DISCHARGE CHUTE MUF FLER ELECTRIC CONTROL LEVER AUGER START DRIVE CONTROL SPEED BUTTON TRACTION DRIVE LEVER GAS O LINE CON TROL CONTROL LEVER FILLER CAP LEVER POWER CORD PLUG CHOKE CHUTE CON- DE FLEC TOR TROL SAFETY IGNITION KEY ON / OFF SWITCH CHUTE PRIM ER DISCHARGE DE FLEC TOR CHUTE KNOB FUEL SHUT-OFF VALVE RECOIL (AUXILIARY) STARTER HANDLE HANDLE CLEAN-OUT TOOL KNOB MUF FLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL TOOLBOX LOCATION ON THE ENGINE. ACTUAL LO

Summary of the content on the page No. 9

OPERATION The operation of any snow thrower can result TO CONTROL SNOW DISCHARGE (See Figs. 11 & 12) in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear WARNING: Snow throwers have ex- safety glasses or eye shields while operating posed rotating parts, which can cause 00155 your snow thrower or performing any ad just- severe injury from contact, or from ma- ments or repairs. W e recommend standard safe ty glasses terial thrown from the discharge ch

Summary of the content on the page No. 10

OPERATION TO THROW SNOW (See Fig. 13) • Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are The auger rotation is controlled by the auger control lever in the direction of discharge) before restarting the engine. located on the right side handle. • Restart the engine, then squeeze the auger control • Squeeze auger control lever to handle to engage the lever to the handle to clear snow from the auger hous- auger and throw snow.

Summary of the content on the page No. 11

OPERATION TO ADJUST SKID PLATES (See Fig. 16) ADD GASOLINE (See Fig. 17) NOTE: The wrench provided in your parts bag may be • Fill fuel tank to bottom of tank filler neck. Do not over- used to adjust the skid plates. fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Skid plates are located on each side of the auger housing Purchase fuel in quan ti ties that can be used within 30 and adjust the clearance between the scraper bar a

Summary of the content on the page No. 12

OPERATION TO START ENGINE 5. Pull recoil starter handle quickly. Do not allow starter rope to snap back. • Be sure fuel shut-off valve is in the “OPEN” position. 6. When the engine starts, release the recoil starter han dle Your snow thrower engine is equipped with both a 120 Volt and slowly move the choke control to the “OFF” posi- A.C. electric starter and a recoil starter. The electric starter tion. is equipped with a three-wire power cord and plug and is designed to operate on 120 Vol

Summary of the content on the page No. 13

MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. SAE 5W-30 Motor Oil To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some See “ENGINE” ad just ments will need to be made periodically to properly maintain your snow thrower. All adjustments in the Service in Maintenance and Ad just ments section of this ma

Summary of the content on the page No. 14

MAINTENANCE AUGER GEAR CASE 1. Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come • The gear case was filled with lubricant to the proper in contact with plug. level at the factory. The only time the lubricant needs attention is if service has been performed on the gear 2. Clean area around drain plug. case. 3. Remove drain plug and drain oil in a suitable container. • If lubricant is required, use only Ronex ED #1 4. Install drain p

Summary of the content on the page No. 15

SERVICE AND ADJUSTMENTS IMPELLER SHEAR BOLTS WARNING: To avoid serious injury, before The impeller is secured to the impeller shaft with two (2) performing any service or ad just ments: capscrew/shear bolts and hex nuts. Should a foreign object 1. Be sure the on/off switch is in the or ice become lodged in the impeller, the capscrews are OFF position. de signed to break, preventing damage to any other com- po nents. If impeller does not turn when auger control lever 2. Remove safety igniti

Summary of the content on the page No. 16

SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 20) 8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around The auger and traction drive belts are not adjustable. If pulleys. the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be HINT: Insert a 3/8" drive ratchet (in the “ON” position) into replaced by a service center/department. the square hole in idler arm and rotate ratchet clockwise to rel

Summary of the content on the page No. 17

SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 21) ENGINE • Remove the klik pin and remove wheel from axle. See engine manual. IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To dis en gage CARBURETOR drive system from the wheels (for pushing or trans port ing Your carburetor is not adjustable. Engine performance the snow thrower), remove klik pin from wheel hub and should not be affected at altitudes up to 7,000 feet (2,134 insert

Summary of the content on the page No. 18

STORAGE Immediately prepare your unit for storage at the end of the NOTE: Fuel stabilizer is an acceptable alternative in min- season or if the unit will not be used for 30 days or more. i miz ing the formation of fuel gum deposits during stor age. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. WARNING: Never store the snow Run engine at least 10 min utes after adding stabilizer to thrower with gaso line in the tank

Summary of the content on the page No. 19

TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF switch is OFF). (or ON/OFF

Summary of the content on the page No. 20

REPAIR PARTS SNOW THROWER - - MODEL NO. PR624ES (96192002901) AUGER HOUSING / IMPELLER ASSEMBLY 1 KEY PART NO. NO. DESCRIPTION 1 404928X428 AUGER HOUSING 2 404931X429 SCRAPER BAR 3 72270505 CARRIAGE BOLT 5/16 −18 X .625 4 155377 NUT 5/16 −18 3 (5x) 4 (5x) 2 01.07.001-A 2 3 1 1 2 KEY PART NO. NO. DESCRIPTION 1 420478 AUGER BEARING 3 2 411939 BEARING PLUG 3 179582 SCREW 5/16 −18 X 1.00 01.07.024-B NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPO


Alternative user manuals
# User manual Category Download
1 Poulan 183615 User manual Snow Blower 0
2 Poulan 185143 User manual Snow Blower 0
3 Poulan 185156 User manual Snow Blower 0
4 Poulan 187879 User manual Snow Blower 0
5 Poulan 185136 User manual Snow Blower 0
6 Poulan 183618 User manual Snow Blower 0
7 Poulan 187881 User manual Snow Blower 0
8 Poulan 187877 User manual Snow Blower 0
9 Poulan 187883 User manual Snow Blower 0
10 Poulan 188047 User manual Snow Blower 0
11 Poulan 183616 User manual Snow Blower 0
12 Poulan 187887 User manual Snow Blower 0
13 Poulan 189539 User manual Snow Blower 0
14 Poulan 189645 User manual Snow Blower 0
15 Poulan 192034 User manual Snow Blower 0
16 Agri-Fab 45-0402 User manual Snow Blower 2
17 Agri-Fab 45-0418 ATV User manual Snow Blower 1
18 Agri-Fab 45-0418 User manual Snow Blower 1
19 Alliance Laundry Systems DRYING TUMBLERS 70269501R3 User manual Snow Blower 2
20 Ariens 924 SNO-THRO 924109 User manual Snow Blower 60