Peavey 6534 user manual

Summary of the content on the page No. 1

™

6534 +
Tube Guitar Amplifier
Operating
Manual
www.peavey.com

Summary of the content on the page No. 2

Summary of the content on the page No. 3

Summary of the content on the page No. 4

Summary of the content on the page No. 5

Summary of the content on the page No. 6

Summary of the content on the page No. 7

ENGLISH 6534 + 7

Summary of the content on the page No. 8

Summary of the content on the page No. 9

Summary of the content on the page No. 10

10

Summary of the content on the page No. 11

™ 6534 + In Out In In In Activates Activates *Selects Effects Loop Crunch Voicing (toggles) when switch on Rhythm between is pressed when switch Rhythm and LED is pressed and illuminates and LED Lead illuminates channels All switches are push on/push off. There are no momentary switches on the footswitch. *NOTE: Channel select switch (14) must be pressed to the “in” position for this switch to function. 11

Summary of the content on the page No. 12

12 6534 + PRE LOW MID HI POST LEAD TUBE STAGES FOOTSWITCH EFFECTS SEND SWITCH FOOTSWITCH LOGIC INPUT SWITCH TUBE BUFFER TUBE STAGE LOGIC RETURN CHANNEL SELECT TUBE STAGES RHYTHM TUBE STAGES PRE LOW MID HI POST SPEAKER OUTPUTS PUSH PUSH TUBE POWER BRIGHT CRUNCH AMP IMPEDANCE SWITCH FOOTSWITCH SWITCH LOGIC PREAMP OUT SIGNAL FLOW BLOCK DIAGRAM RESONANCE PRESENCE RESONANCE PRESENCE LEAD RHYTHM

Summary of the content on the page No. 13

6534 + EFFECTS RETURN: POWER AMPLIFICATION PREAMP SECTION Impedance: Very High Z, 470 k ohms The following specs are measured @ SECTION Designed Level: -10 dBV, 300 mV RMS 1 kHz with the controls preset as follows: RATED POWER AND LOAD: Low and High EQ @ 10 120 W RMS into 16, 8, or 4 ohms PREAMP OUT: Mid EQ @ 0 Load Impedance: 47 k ohms or greater Bright out POWER @ CLIPPING: Nominal Output: +10 dBV, 3 V RMS Lead and Rhythm Posts @ 10 (Typically @ 5% THD, 1 kHz, 120 V AC Presence and Res

Summary of the content on the page No. 14

DEUTSCH 6534 + 14

Summary of the content on the page No. 15

Summary of the content on the page No. 16

Summary of the content on the page No. 17

17

Summary of the content on the page No. 18

™ 6534 + In Out In In In Aktiviert Aktiviert *Auswahl Effektschleife, Crunch Voicing (Umschalten) wenn Schalter am Rhythm-Kanal, zwischen Rhythm- gedrückt wird wenn Schalter und Lead-Kanal. und LED leuchtet. gedrückt wird und LED leuchtet. Alle Schalter sind einrastende Ein/Aus-Schalter. Am Fußschalter gibt es keine Momentschalter (Taster). *HINWEIS: Der Kanalwahlschalter (14) muss gedrückt werden, damit dieser Schalter funktioniert. 18

Summary of the content on the page No. 19

19 6534 + PRE LOW MID HI POST LEAD TUBE STAGES FOOTSWITCH EFFECTS SEND SWITCH FOOTSWITCH LOGIC INPUT SWITCH TUBE BUFFER TUBE STAGE LOGIC RETURN CHANNEL SELECT TUBE STAGES RHYTHM TUBE STAGES PRE SPEAKER LOW MID HI POST OUTPUTS PUSH PUSH TUBE POWER CRUNCH BRIGHT AMP IMPEDANCE SWITCH FOOTSWITCH SWITCH LOGIC PREAMP OUT SIGNAL FLOW BLOCK DIAGRAM RESONANCE PRESENCE RESONANCE PRESENCE LEAD RHYTHM

Summary of the content on the page No. 20

6534 + EFFECTS SEND: ENDSTUFE VORVERSTÄRKERSTUFE Verbraucherimpedanz: Die folgenden technischen Daten NENNLEISTUNG UND NENNLAST: 47 kOhm oder darüber wurden bei 1 kHz mit folgenden 120 Watt RMS an 16, 8 oder 4 Ohm Nennleistung: -10 dBV, 300 mV RMS Reglervoreinstellungen gemessen: LEISTUNG BEI CLIPPING: Low und High EQ auf 10 EFFECTS RETURN: (Typisch bei 5% Klirrfaktor, 1 kHz, 120 V Mid EQ auf 0 Impedanz: Sehr hochohmig, 470 kOhm Wechselstromleitung) Bright ausgeschaltet Gedachter P