Summary of the content on the page No. 1
9/t~ inch wrench
~ odiustable wrench
inch wrench
¯ hammer or rubber mallet
inch wrench
¯ s~2 allen wrench
¯ THE PARABODY FACTOR 625 BASE UNIT MUST BE ASSEMBLED ON A FLAT, LEVEL SURFACE TO ASSURE ITS PROPER FUNC1
¯ PARABODY STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSEMBLED BY TWO PERSONS TO AVOID POSSIBLE INJURY.
,, KEEP ALL FRAME BOLT CONNECTIONS LOOSE UNTIL INSTRUCTED IN THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTi
MAKE SURE SNAP HOOKS ARE FASTENED BEFORE DOING EXERCISES.
NOTE: We recommend
Summary of the content on the page No. 2
TTS/PARTS: OTY. NAME/DESCRIPTION 1 ~(P~78-011 ~ 1 ~--~B0-01 ) Back Pod 1 ~PB3170-01) Leg Press Frame l Telescoping Tube Plated ~"-’~43-01) 1 ~~- -- (PB3047-01) 1 [PB3OBI-01) Pivot Axle __ l (PB3236-01) Leg Press Cable 17’~ ~634-01) 4 Non-Skid Strip 4" x count all parts before beginning assembly. ’ARE: QTY. NAME/DESCRIPTION ’ - Gr---’-~p I I/4 " x S" 2 ~/4" x I" Oilite Bushing -- I ~Compressi.___~on Spr~ l Co~e~ Pin l P~unger 1 Spacer l Knob ~" Square E.nd_ Cop (I 0-I 4 ga)~ l Weight Stock Bumpe
Summary of the content on the page No. 3
If you have installed a second weight stack, go to Figure 5. If you have not purchased the second weight stack, please camp]ere the folJowing steps before proceeding to F~gure 5. 1.Remove the blank shroud from the rear of the Factor 625. ELASTIC SHOCK CORD 2. Remove the rotary cable from the unit and also the assadated shock cord. 3. Load the Leg Press Cable into the D-Ring in the position the Rotary Cable was LEG PRESS CABLE removed from. Remove the elastic shock cord (PB3236-01) from the Rotar
Summary of the content on the page No. 4
~tinue to route Leg Press cable as shown. CA.BL~ RETAINING CLIP ,. ,~emave the boll used to hold the la~ boom 1o ~’he tube an the rear of" lhe Main Frame and ~aih one I1) 4~.,~" w/l" Clevis Pulley and one (1) cable retaining clip using one (t) ~-~" x 4(.’~’" bolt and the existing 34" Locknu~ and 34" Washer supplied. Raule cable as LEG PRESS CA,BLE (PB3626-01) shown. Locme ~able retaining clip approxim~ety as shown. ,4: 2" w/1 " CLL-VIS PULLEY- 2 PL Remove the bolt used to hold the pulley in the
Summary of the content on the page No. 5
AHach the Leg Press Frame to the Main Frame 1. ---~ V:’x4V2"BOLT-2 ~ on lop using two {2) l~"x 41~" Bolts, b"2 ~ WASHER - 2 PL b~" LOCK WASHER - 2 PL two (2) 1/2" Washers, two (2) I/2" Lockwashers ~,,’2" NUT - 2 PL and two (2) 1,~,, nuts. Attach four (4) 4" x17" Non-Skid Strips to the 2. angled foot pl~e on the Leg Press Frame as shown. 3. Install two (2) 2" Square End Caps {10-14 ga) into the angled tubes on the Leg Press Frame and two (2) 2" Square End Caps (10-14 ga)into the base tubes of the
Summary of the content on the page No. 6
SPACER SPR~NG ".--~~ble the spring pin assemblT to the co~ P~N ~autum Frame using one (1) knob, one (I) ~kUNG~ plunger, one (1) spring, one (1) spacer, and (1) co~e~ pin, using the folJowing steps: ~ ~semble the knob to the p~ungsr B. In~d the plunger through the fi~ housing and through the fir~ hole of the second housing. ~~ C Slip ~e Spring and the spacer over the end ~os of the plunger (in that order). D. Insed the plunger through the second hole of G~ ~ ~" x 5 ~- 2 ~k the housing. E PulJ ba
Summary of the content on the page No. 7
nser~ the seat adjustment tube Into the front end If] of the Pendulum flame. Pull back the spring pin Fig a~mb/y, and advance the seat adjustment tube If’ al1 the way in. (Make sure tab ai the front end of the seat adiustment tube is up. See figure] I). 2..Securely fasten one fl) 3~,’ x 1 ]/4" Bob one (1) 1. ~’~" ~ 1,4 BOLT 3/e" Lockwasher, and one (1 }3,~,, Nut to ~he hole s,,~- LOCK WASHE~ in ~e rear of the seat adju~ment tube, on the W ~ unde~ide of the Pendulum Frame be~een the sbt. ~See Det
Summary of the content on the page No. 8
. _~.nch the Pendulum Frame to the leg press PENDULUM FRAME e by sliding the pivot axle thrnugh the col!ars on the pivot tabs of the leg press flame and through the pivot tube at the top of the pendulum flame. Thread two (2) sA6" x I/4" Ig. set screws into both collars and tighten. {This ~ep 5/16" x 1/4~ LG SET SCR.~v’ -2 PL may be pre-nssembled) PIVOT AXLE LEG PRESS FI Atlach the cable assembly to the telescoping tube with 1. the Clevis pin and wire clip supplied on cable. LEG PRESS CABLE (PB32
Summary of the content on the page No. 9
(2).~/8"x ock res~ 11/~’~Bohs tube on the two Pendulum (2) ~,~" Frame Lockwashe~, using two ’ ana ~o ~2) ~8’ Washe~. NOTE: HOL~ IN ~E BACK OF THE S~T BACK PAD AND ~E S~T PAD. 2. Iflse~ on~ ( ~ ) 2"~quare ~nd cap ( ~ 0-14 g~;)in the top ot ~he back re~ tuoe and one (1) square end cop in the end of the pendulum frame under ~he back rest tube. 2" SQ. END CAP - 2 PL 3/e" x 11/,,- BOLT -- 2 PL 3/e" LOCKWASHE~S _ 2 PL 3,,~ WASHER .- 2 PL lure Frame, uu,,g two {’2) 3~ x ] i ,, " ....... ~-= " 8 74 Bo
Summary of the content on the page No. 10
ten any loose connedions at this time. ~r FACTOR 625 should be assembled as 11
