Summary of the content on the page No. 1
358
EX350 HOME GYM
PRODUCT ASSEMBLY
R~VI~ION C
Summary of the content on the page No. 2
358 EX350 ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY HARDWARE: ,.. ITEM NAME/DESCRIPTION QTY 1/2 X 3 IN. HEX HEAD BOLT ............................................................................ : ................. 4 I.~ X 3 I/4 IN. HEX HEAD BOLT - 4. 1/2_ X 4 IN. HEX HEAD BOLT ........................................................... : .................... : ............. I 318 X ! i/2 IN. HEX HEAD BOL " 1 T 3/8 X I 3,’4 IN. HEX HEAD BOLT ........................
Summary of the content on the page No. 3
EX350 ASSEMBLY PARTS LIST 358 SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY WELDMENTS/PARTS: ITEM. NA~IE/DESCRIPTION QTY BEARING HOUSING WLDMT ........................................... (6293701) ............................... 1 LOW ROW SWIVEL BRACKET WLDMT ......................... (6199401) ........................... :... 1 2. ¯ MAIN UPRIGHT BOTTOM SECTION WLDMT ................ (638.101) ............................... 1 .~. LEFT PEC DEC ARM WLDMT .....................................
Summary of the content on the page No. 4
358 EX350 ASSE.~B! ,Y INSTRUCTIONS NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE; HEAD OF THE BOLT. " iii!!ii-il BOLT LENGTH BOLT LENGTH RULER: .0 ~ 5 6 !," t ¯ I .... !.. 1 ! ,I,, l, I , , ! I ,! I.
Summary of the content on the page No. 5
EX350 A:~SEtvlBLY INSTRUCTIONS 358 .; ,THANK YOU " : ~2..-~.-_:. :." . . ." ....~ ~---~.. FOR PURCHASING THE ~ PLEASE SAVE THESE ASSEMBLY INSTRUCTIONs FOR YOUR PERSONAL REFERENCE, AND ADDITIONAL SERVICE INFORMATION.,~,~" . ¯ ***IMPORTANT*** ":: THE EX350 MUST BE ASSEMBLED ON A FLair, LEVEL SURFACE TO ASSURE ITS:’’"~ FUNCTION. PARABODY INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASsEMBI~ED. PERSONS TO AVOID POSSIBLE INJURY. KEEP ALL FRAME CONNECTIONS LOOSE, UNTIL INSTRUCTED IN THE ASSEMI SEQUEN
Summary of the content on the page No. 6
358 EX350 ASSE~.,IBLY INSTRUCTIONS Attach BACK/SEAT SUPPORT ASSEMBLY to WEIGHT STACK SUPPORT BASE, u~ing one (1) I/2 X 3-1 ’4 IN. HEX HEAD BOLT and one (1) I/2 IN. LOCKNUT. (TIGHTEN ONLY UNTIL SNUG) .Attach one (1) 4-1.’20.D. DIA. [~ULLEY with’l IN. BUSHING into FRONT "U" PULLEY BRACKET of the BACK/SEAT SUPPORT, using one (1) 3/8 X 1-3/4 IN. HEX HEAD BOLT and one (1) 3/8 LOCKNUT. .. Attach one (I) 4-I;20.D. D1A. PULLEY, with 2 IN. BUSHING, between two fiats on MAIN UPRIGHT TOP SECTION. usln,...
Summary of the content on the page No. 7
EX350 ASSEMBLY INSTRUCTIONS 358 USING,EXTREME CARE. slide each of the fifteen (15) WEIGHT PLATES down ow.’r the GUIDE RODS onto the WEIGHT STACK CUSHIONS. (PIN HOLE FACING OUT) 22. Slide HEAD WEIGHT PLATE ASSEMBLY down over the GUIDE RODS onto the WEIGHT STACK. Position the GUJDE RODS under the GUIDE ROD BRACKET ofthe MAIN UPRIGHT TOP SECTION, and hold in place using two (2) GUIDE ROD PINS. (SEE DETAIL Apply the WEIGHT STACK LABELS to the WEIGHT PLATES¯ (SEE DETAIL A) 24. 25. Insert one (I) 1-I
Summary of the content on the page No. 8
358 EX350 ASSEMBLY INSTRUCTIONS LOOSELY assemble one (1) 3 I/20.D. DIA. PULLEY with I IN. BUSHING into PULLEY BRACKET on the LEG CURL ARM ASSEMBLY. ..... Using one (1) 3/8 X 2 IN. HEX HEAD BOLT and one (1) IN. LOCKNUT. Attach two (2) ROLLER PADS to the LEG CURL ARM ASSEMBLY. using one (I) ROLLER 37. SHAFT. and two (2; STAR LOCK COLLARS. (NOTE: WHEN USING THE LOW PULLEY OFF THE LEG CURL ARM ASSEMBLY, LOCK IN PLACE BY INSERTING L-PIN INTO BUSHING ON THE LEG CURL EXTENSION NECK) Assemble two (2}
Summary of the content on the page No. 9
EX350 ASSEMBLY INSTRUCTIONS 358 PuII.CABLE up to the PULLEY in the PULLEY HOUSING above the WEIGHT STACK on the MAIN UPRIGHT TOP SECTION. Pull CABLE over and down PULLEY and thru hole in MAIN UPRIGHT TOP SECTION to SELECT CENTER SHAFT on HEAD WEIGHT PLATE. (REMOVE PULLEY FOR EASE OF INSTALLATION) Attach the PRIMARY CABLE to the HEAD WEIGHT PLATE ASSEMBLY. b.v threading the STUD into .the SELECT CENTER SHAFT and TIGHTEN COMPLETELY. To install the SECONDARY CABLE. start by inserting the end of’the
Summary of the content on the page No. 10
EX350 ASSEMBLY INSTRUCTIONS 358 SECURELY assemble the BACK PAD to MAIN UPRIGHT using two (2) 3/8 X 3 IN. FlEX HEAD 53. BOLTS and two (2) 3:8 IN. LOCK WASHERS. (HIDEM WELT CLIP SHOULD BE FACING DOWN) To assemble the PEC DEC LOOP CABLE, start by LOOSELY attaching each end of the CABLE to ¯ 54. CAMS of the LEFT and RIGHT PEC DEC ARMS, using two (2) 5116 X I IN. HEX HEAD BOLTS.four (4) 5 "16 IN. WASHERS. two (2) 5/16 IN. LOCK WASHERS. and two I’.2) 5/16 NUTS. (SEE DETAIL C) Rut1 CABLE back to the P
Summary of the content on the page No. 11
EX350 ASSEMBLY INSTRUCTIONS 358 Assembl~ one ( I ) SPRING PIN ASSEMBLY to the SPRING PIN ASSEMIIILY HOUSING located 61. the SEAT SUPPORT TUBE using one (l) KNOB, one (l) PLUNGER. one (1) SPRING, one SPACER. and one (l) COTTER PIN. (SEE DETAIL Insert one ( I ) I i 2 IN. SO. END CAP 12 GA into end ofthe SPRING PIN ASSEMBLY HOUSING 62. fl~e SEAT SUPPORT TUBE. (SEE DETAIL H) Insert one ( I ) 2 IN. SQ. ENID CAP into front end of the ADJI]STABLE SEAT SUPPORT. 63. Assemble t~vo (2~ ROLLER PADS to t
Summary of the content on the page No. 12
....SEE bETAIL’F"
Summary of the content on the page No. 13
1"7_ PL C.5.") ¯ SEE ° DETA ~L’F
Summary of the content on the page No. 14
Summary of the content on the page No. 15
PULLEY tSF1,At.K ET .--tPF.r. DEr AF, M LEF’r I PEr.. D’EC" P, ACK DRAWING ParaBody, Inc. RAMSEY. MINNESOTA ~{~ DE.TA IL "C."
Summary of the content on the page No. 16
HQ~3K r - ~/a" NU’f’ ,. H~lt ’’ P ULLI"’i’ W/I" BU~H~rNG
Summary of the content on the page No. 17
’ .BOLT ¯ /g SPLITL.~,K ¯ WA.SHEP,
Summary of the content on the page No. 18
¯ o o oo ROLLER PAD SHAFT
Summary of the content on the page No. 19
