ParaBody 908101 ST user manual

Summary of the content on the page No. 1

.~erious Steel
908101 ST LAT MACHINE
II I
ASSEMBLY INSTRUCTIONS
Revision: 02/24/97
1
Part # 6677801

Summary of the content on the page No. 2

[IMPORTANT NOTES I There is a risk assumed by individuals who use this type of equipment. To rnin,imize risk, please follow these rules: 1. Consult your physician before beginning any exercise program. 2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 3. Do not allow minors or children to play on or around this equipment. 4. Exercise with care to avoid injury. 5. If unsure of proper use of equipment, call

Summary of the content on the page No. 3

[ PARTS LIST DESCRIPTION QTY KEY PART # DESCRIPTION QTY KEY PART # 15 6637102 SE,~ 1 6671803 BENCH FRAME 1 1 TOP BOOM 1 16 6676802 KN~ PAD 2 6673703 2 I 17 3102917 1/2 X 4" BOLT 12’ KNEE SUPPORT 3 6672202 UPRIGHT 1 18 3102910 1/2’ ’X 3’" BOLT 2 4 6674103 19 3102~22 FOOT SUPPORT 1 3/8 X 2-3/4" BOLT 8 6674402 5 1 20 3102902 3/8 X 2-1/4" BOLT 2 ’" ~OWER 6 6(~72703 3102924 3/8 X 1-3/4"BOLT 4 TOWER BRACE 1 21 7 6674603 2 22 3102502 1/~ " WASHER 12 6z~89902 PLATE, 1/4 X 2 X 7-1/~ 8 1 23 3102501 3/8" W

Summary of the content on the page No. 4

1/2 X 4" 1/2 X 4" FIGURE 2 STEP 3: 1/2" Loosely attach UPRIGHT (4) to BENCH FRAME (1) using four 1/2 X 4" BOLTS (17), WASHERS (22), and fi3ur 1/2" LOCK NUTS (24) as shown in FIGURE FIGURE 3 STEP 4: Securely attach four 3-1/2" PULLEYS (14) to the TOP BOOM (2) using four 3/8 2-3/4" BO LTS (19), eight 3/8" FLANGE SPACERS (26), and four 3/8" LOCK NUTS (25) as shown in FIGURE 2 3 4 0 1 5 6 I I I I I I I [ I I I [ I I.L.,[ I__l 4

Summary of the content on the page No. 5

1/2 X 4" 1/2 X 4" FIGURE 4 STEP 5: A. Loosely attach TOP BOOM (2) to TOWER (6) and UPRIGHT (4) using 1/2 X 4" BOL TS (17), four 1/2" WASHERS (22), and three 1/2" LOCK NUTS (24) as shown in FIGURE B. Securely tighten all loose frame connections made to this point. 1/2 X 3" 3/8 X 2-3/4"t FIGURE 5 STEP 6: A. Securely attach FOOT SUPPORT (5) to the BENCH FRAME (1) using two 1/2 X 3" BOLTS (18), two 1/2" WASHERS (22), and two 1/2" LOCK N~TS (24) as shown in FIGURE B. Securely attach SEAT PAD (15) t

Summary of the content on the page No. 6

FIGURE 6 STEP 7: A. Securely attach two KNEE PADS (16) to KNEE SUPPORT (3) using four 3/8 IX 1-3/4" BOLTS and four 3/8" WASHERS (23). See FIGURE B. Slide KNEE SUPPORT (3) over square tube on BENCH FRAME (1). Make sure SPRING HOUSING on the K~NEE SUPPORT (3) is facing away from the SEAT PAD. See FIGURE 6 & STEP 8: FIGURE 7 Securely thread 3/8" SPPd[NG PIN (27) to the SPRING PIN HOUSING on the KNEE SUP- PORT (3) as shown in FIGURE 4 2 3 5 6 0 [ I I I I I I I [ I 1.1_] I__1 I I

Summary of the content on the page No. 7

STEP 9: Assemble two 7-1/4" PLATES (8) to two 4-1/2" PULLEYS (13) using two 3/8 X 2-1/4" BOLTS (20), four WASHERS (23), and two 3/8" LOCK NUTS (25). FIGURE 8. FIGURE FIGURE 9 STEP 10: Securely assemble one 4-1/2" PULLEY (13) to the UPRIGHT (4) using two 3/8 X 2,-3/4" BOLTS (19), two 3/8" FLANGE SPACERS (26), two 3/8" WASHERS (23), and two 3/8" LOCK NUTS (25). FIGURE 9. THIS CONCLUDES THE ASSEMBLY OF THE 908101. PLEASE REFER TO THE 912101 OR 913101 INSTRUCTIOHS ON HOW TO ASSEMBLE TIlE WEIGHT O