Summary of the content on the page No. 1
829 LEG CURL/EXTENSION
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H 1
Version: 829108
PART # 7302401 Revision: 06/13/02
REV . A
Summary of the content on the page No. 2
TABLE OF CONTENTS Safety Statement.............2 Parts list..........................5 General Notes..................3 Assembly Instructions.....5-8 Tools Required................3 General Maintenance.......9 Gym Layout.....................4 Warranty Statement..........10 Product Services..............11 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES! 1. Before using, read all the
Summary of the content on the page No. 3
IMPORTANT NOTES Please note: * Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. Tools Required for Assem
Summary of the content on the page No. 4
1’ 2’ 3’ 4’ 5’ 1’ 2’ 3’ 4’ 5’ 6’ 1 Square = 1’ X 1’ 4
Summary of the content on the page No. 5
PARTS LIST KEY PART # QTY KEY QTY DESCRIPTION PART # DESCRIPTION 1 LEA6259109 1 20 8 FRONT SUPPORT TUBE LEA3235212 3/8 X 3" BOLT 2 LEA6625410 1 21 2 BACK PAD ADJUST TUBE LEA3235216 3/8 X 4" BOLT 3 LEA6625510 1 22 1 BACK PAD SUPPORT TUBE LEA3235316 1/2 X 4" BOLT 4 LEA6216710 1 1-3/4 SQ X 5" TUBE 23 1 LEA3235428 1/2 X 7" BOLT 5 LEA6668210 1 24 20 1-3/4 SQ X 13-1/2" TUBE LEA3114403 3/8" FLAT WASHER 6 LEA6662010 1 25 4 LEG CURL/EXTENSION LEA3114702 3/8" NYLOCK NUT 7 LEA6661221 1 26 2 BACK PAD
Summary of the content on the page No. 6
36 12 STEP 1: Insert four COVER END CAPS (37) into 37 the ends of REAR BASE LEG (12) and FRONT BASE SUPPORT (1). See FIGURE 1 1. 37 STEP 2: Slide two 1-1/4 x 5” GRIPS (36) over tubes on REAR BASE LEG (12). See FIGURE 1. FIGURE 1 12 11 25 STEP 3: Securely assemble REAR BASE LEG (12) 24 to LEG FRAME (11) using two 3/8 X 3” BOLTS (20), four 3/8” FLAT WASHERS (24), and two 3/8” NYLOCK NUTS (25). See FIGURE 2. 24 20 3/8 X 3” FIGURE 2 11 STEP 4: Securely assemble FRONT BASE SUP- PORT (1) to LEG FRAM
Summary of the content on the page No. 7
FIGURE 5 27 LOW HEIGHT 29 STEP 6:Securely assemble RIGHT (9) & LEFT (10) 24 LEG EXT HANDLES to LEG FRAME (11) using two 3/8 X 4” BOLTS (21), four 3/8” 10 29 FLAT WASHERS (24) , and two 3/8” LOW 11 HEIGHT NYLOCK NUTS (27). See FIG- URE 5. STEP 7:Insert two 3 X 2” END CAPS (29) into 9 the leg frame as shown in FIGURE 5. 24 21 3/8 X 4” FIGURE 6 18 STEP 8:Securely assemble one 1/2” SPRING PIN AS- SEMBLY (18) into the spring pin barrel on the 11 LEG FRAME (11) as shown in FIGURE 6. FIGURE 7 2 ST
Summary of the content on the page No. 8
FIGURE 8 STEP 10:Securely assemble BACK PAD ADJUST TUBE (2) & BACK PAD SUPPORT TUBE 3 (3) to LEG FRAME (11) using one 1/2 X 7” 26 BOLT (23) and one 1/2” LOW HEIGHT 2 NYLOCK NUT (26). (NOTE: SECURELY TIGHTEN BOLT THEN BACK NUT OFF 11 1/4 TURN TO ALLOW THE TWO PARTS 23 1/2 X 7” TO ROTATE FREELY.) See FIGURE 8. FIGURE 9 STEP 11: Securely attach the BACK PAD (7) 20 3/8 X 3” to the BACK PAD TUBES (2 & 3) 3 24 7 2 using four 3/8 X 3” BOLTS (20) and four 3/8” FLAT WASHERS (24). See FIGURE 9. F
Summary of the content on the page No. 9
FIGURE 11 31 STEP 13: Slide two HINGE TABS (31) over posts on LEG FRAME (11). See FIGURE 11. 11 31 FIGURE 12 8 STEP 14: Securely attach the SEAT PAD (8) to the HINGE TABS (31) using two 3/8 X 1” BOLTS (19) and two 3/8” FLAT WASH- ERS (24). See FIGURE 12. 31 24 19 3/8 X 1” :Attach two ROLLER PADS (15) to the STEP 15 LEG FRAME (11) using one 17” ROLLER 35 PAD SHAFT (14) and two STARLOCK 15 COLLARS (35). See FIGURE 13. 11 14 15 35 FIGURE 13 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 9
Summary of the content on the page No. 10
4 5 33 STEP 16:Attach eight 1-1/2” X 3/4” GLIDES (33) to 5” ROLLER PAD ADJUSTER (4) and attach eight 1-1/2” X 3/4” GLIDES (33) to 13-1/2” ROLLER PAD ADJUSTER (5) as shown in FIGURE 14. FIGURE 14 6 STEP 17: Securely assemble two 3/8” SPRING PIN AS- SEMBLIES (17) into the spring pin barrels on the LEG CURL/EXTENSION (6) as shown in FIGURE 15. 17 17 FIGURE 15 28 6 4 STEP 18:Insert 5” & 13-1/2” ROLLER PAD 28 ADJUSTERS (4 & 5) in the ends of the LEG CURL/EXTENSION (6). Pull back on SPRING PINS u
Summary of the content on the page No. 11
STEP 20:Insert two 1/2” FLANGE BEARINGS 26 LOW HEIGHT (34) into the LEG CURL/EXTENSION (6). See FIGURE 17. STEP 21:Securely assemble LEG CURL/EX- TENSION (6) to LEG FRAME (11) 6 using one 1/2 X 4” BOLT (22) and one 1/2” LOW HEIGHT NYLOCK NUT 34 (26). (NOTE: SECURELY TIGHT- EN BOLT THEN BACK NUT OFF 11 1/4 TURN TO ALLOW THE PART 32 TO ROTATE FREELY.) See FIG- 22 1/2 X 4” URE 17 Attach one 3/4” SQUARE RUBBER STEP 22: BUMPER (32) between the contact point of the LEG CURL/EXTENSION (6) and FIGU
Summary of the content on the page No. 12
MAINTENANCE Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your ParaBody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately. Failure to do so may result in serious injury * PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION
Summary of the content on the page No. 13
LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product. 2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will
Summary of the content on the page No. 14
LIFE FITNESS 14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A. Tel: 763.323.4500 Fax: 763.323.4797 800.328.9714 (Toll-free within the U.S. and Canada) www.parabody.com INTERNATIONAL OFFICES Life FitnessAtlantic BV Life Fitness (UK) Ltd. Atlantic Headquarters Queen Adelaide Bijdorpplein 25-31 Ely, Cambs CB7 4UB 2992 LB Barendrecht United Kingdom The Netherlands Phone CSS: (01353) 665507 Phone: (180) 646 666 Fax CSS: (01353) 666719 Fax: (180) 646 703 Life Fitness EUROPE GmbH Lif
