Summary of the content on the page No. 1
P1
Model iP47
Bluetooth
Alarm Clock Radio
®
for iPhone / iPod
Questions? Visit www.ihomeaudio.com
Summary of the content on the page No. 2
P2 Table of Contents 1-2 Quick Start 3 Controls and Indicators 3 iP47 Display 4 Using the iP47 5 Using the Alarms 6 Listening to iPhone/iPod 6 Listening to Radio 7 Listening to other portable audio devices 7 Listening to Bluetooth Music 8 Making Calls with Bluetooth Mobile Phone 8 Sleep Operation 9 Dimmer Operation 9 Remote Control 10 Install Clock Backup Battery 10 Replacing the Remote Control Battery 11 A Consumer Guide to Product Safety 12-15 Trouble Shooting 16 Warranty NOTE : The iP47 is
Summary of the content on the page No. 3
P3 FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tes
Summary of the content on the page No. 4
o o P4 Quick Start 1: Power 2: Pair Your Bluetooth-enabled Phone With The iP47 A 10:09 10:09 B Connectivity Bluetooth On Infrared Off RESET Packet data TEST Data transfer Select Back Select Back a) Select Bluetooth/discover mode on your phone (see your user manual) b) Press and hold the Play/Pause button on the iP47. The unit will enter Auto-pairing mode and begin searching for a device to pair with, indicated Attach AC adaptor cable to jack by flashing Bluetooth and pairing icons. on ba
Summary of the content on the page No. 5
P5 Quick Start 7: Inserts 8:iPhone/iPod Insert an iPhone or iPod Select the dock insert for into the dock with proper your iPhone or iPod insert (iPhone/iPod must model from the table not be in a skin or case). The below and place insert in iPhone/iPod will charge dock. while docked. Press the Never dock your iPhone Play/Pause Button on the or iPod without an insert iP47 to play your in place. iPhone/iPod. iPod nano 4G iPhone 3G iPod touch 2G Use this insert insert 16 inser
Summary of the content on the page No. 6
P6 Controls and Indicators Universal dock for iPhone/iPod Snooze/Dimmer Button Microphone Radio Preset Button Alarm 1 Button Sleep Button Alarm 2 Button Alarm On/Off Button Volume Up Up Button Volume Down Down / Set Button iPod Mode Button radio Alarm Reset/Power Button (iPod, Bluetooth, FM1, FM2, AM or line in) Play/Pause Button (for iPhone, iPod and End Button Bluetooth music) Talk Button Clear Button Ringer vol. Button Alpha-Numeric Phone Keypad DST switch Time Zone Button Line in Ja
Summary of the content on the page No. 7
P7 Using the iP47 Connecting the iP47 to Power Source Connect the AC adaptor cable plug into the jack on the back of the system, then plug the AC cord of the AC adaptor into the wall outlet. Turning the iP47 ON or OFF Press the Button on the iP47 or on the remote control at any time to turn the iP47 On or Off. Note that a docked iPhone or iPod will continue to charge when the unit is turned off as long as the AC adaptor is plugged in. Setting Up the iP47 The iP47 clock is preset to U.S.
Summary of the content on the page No. 8
P8 Using the Alarms Setting the Alarms Alarm 1 (wake to iPhone/iPod or Bluetooth device) 1. Press and hold the Button until the hour display flashes. Press the or Button to set the alarm hour (hold for a few seconds to advance or reverse rapidly). Remember to set the correct AM or PM wake time. An icon in the upper right hand corner of the time display is the PM Indicator; there is no AM indicator. 2. Press the Button again. The minute display will flash. Press the or Button to a
Summary of the content on the page No. 9
P9 Listening to iPhone or iPod 1. Dock an already playing iPhone or iPod (always use proper insert, see table on page 2). The iP47 will automatically turn on and you will hear the audio playing from your iPhone/iPod. Note: If the audio source volume is too low on the iPhone/iPod, the iP47 may not detect that the iPhone/iPod is in play mode. If so, pressing the Alarm Reset/Power Button on the main unit once should make it play. 2. When the iPhone/iPod is docked and in standby mode, press the
Summary of the content on the page No. 10
P10 Listening to other portable audio devices You can play a MP3 player or other portable audio device through the iP47 via the Line in Jack. 1. Plug one end of an audio patch cord (available at http//:www.ihomeaudio.com) into the headphone or line-out jack on your device and the other end of the patch cord into the iP47 Line in Jack, located on the back of the unit. 2. Turn on the iP47 and press the Mode button until “Line in” appears in the lower part of display, indicating Line in playing
Summary of the content on the page No. 11
P11 Making Calls with a Bluetooth Mobile Phone Before you make a call with the iP47, you need to pair and link your Bluetooth-enabled phone with iP47. Please refer to Pairing procedure on page 7. Answer a Call: 1. To answer a call, press the Button. Now you can use the iP47 as a speaker phone. 2. Speak into the MIC (located below the Snooze/Dimmer Button) and press the or Button on the iP47 or on the remote control to adjust the call volume. 3. To end the call, press the
Summary of the content on the page No. 12
P12 Remote Control - Press POWER / alm reset to turn unit on or off and reset alarm to come on the next day. - Press MODE to select iPod, Bluetooth, FM1, FM2, AM or Line in mode. - Press PLAY/PAUSE to play iPhone/iPod/Bluetooth and to pause and to resume play. - Press VOLUME BUTTONS to adjust volume level. - Press FWD/REV to skip to next or previous track. Hold for high speed music scan. Press to scan the radio frequency manually. Hold for autoscan radio frequency. - Press PRESETS button t
Summary of the content on the page No. 13
P13 Install Clock Backup Battery The iP47 uses 3 x AA backup battery system to provide backup Replace Backup Battery alarm operation and clock settings in the event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. 1. Open backup battery co
Summary of the content on the page No. 14
P14 A Consumer Guide to Product Safety When used in the directed manner, this unit has been designed and manufactured to assure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use. Keep these instructions handy for future reference. Take special note, and adhere to all warnings on the unit and in the instruction and service manual. 1. Water and Moisture
Summary of the content on the page No. 15
P15 Trouble Shooting Symptom Possible Problem Solution Unit doesn’t respond AC adaptor isn’t plugged to a wall outlet or Plug the AC adaptor into a wall outlet and plug the connector into (no power) the connector is not plugged into the power the AC jack on the unit supply jack on the back of the unit. Wall outlet is not functioning Plug another device into the same wall outlet to confirm the outlet is working. If the outlet is controlled by a switch, check that the switch is ON. Power is off
Summary of the content on the page No. 16
P16 Trouble Shooting Symptom Possible Problem Solution Can't wake to Device is not in play mode Make sure your device is powered and streaming music Bluetooth music Make sure your device is adequately charged to last through Device is not charged the set alarm time Device does not support A2DP and AVRCP If your device does not support the A2DP and AVRCP Bluetooth profiles profiles, set your alarm to wake to radio Raise volume on the iP47 Calls don't Volume on iP47 is too low sound clear Poor
Summary of the content on the page No. 17
P17 Solución De Problemas Síntoma Causa posible Solución La unidad no funciona El adaptador de AC no está conectado al Conecte el adaptador de AC a un tomacorriente y el (no circula corriente tomacorriente o el conector no está conectado conector a la ficha de salida AC de la unidad. eléctrica). a la ficha en la parte posterior de la unidad. El tomacorriente no funciona. Coloque otro aparato al tomacorriente y confirme su funcionamiento. Si el tomacorriente tuviera un selector de encend
Summary of the content on the page No. 18
P18 Solución De Problemas Síntoma Causa posible Solución La música con El aparato no está en modo “Play” (reproducción). Asegúrese que el aparato esté conectado y transmitiendo música. Bluetooth no Asegúrese que el aparato tenga carga suficiente como para El aparato está descargado. funciona como durarle hasta la hora programada. despertador. El aparato no soporta tecnología Bluetooth Si su aparato no soporta tecnología Bluetooth A2DP y AVRCP, A2DP y AVRCP. coloque su despertador para sonar
Summary of the content on the page No. 19
P19 Limited 1 Year Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should this fail to resolve the matter and service s
