Summary of the content on the page No. 1
Serious Ste~
445103 425 SECOND STACK OPTION
ASSEMBLY INSTRUCTIONS
I
l~evision: 09/25/97
Part # 6747401
Summary of the content on the page No. 2
[IMPORTANT NOTES[ WELCOME TO THE WORLD OF Seeiou~ Please note: * Thank you for purchasing the Parabody 445103 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and flame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative ’at (800) 328-9714. The
Summary of the content on the page No. 3
PARTS LIST PART# DESCRrPT~Or~ PART# DESCRIP ~N I 6523401 GUIDE ROD 2 10 3102501 3/8" WASHF, R 2 6266001 WEIGHT STACK SHAFT ’" 3102802 3/8" LOCKNUT 2 3 6375902 1-i/4 SQ. X 4-7/8 ~E 12 6480301 3/8" FLANGE SF’ACER 4 671~601 ~ PLA~BLA~ 3102922 3/8X2-3~" DLT 6747501 P~SS-S~ACK ~LE 5 3102901 3/8X 1-1~" DLT 1 6 3’116101 4~’i/~" P~LEY 3102503 3~"WASHER 2 *h~4o~ SVA~e~ 1 16 6214501 WEIGHTF~ATE 15 8 3108002 ~IG~ STA~ COSmON 2 17 6382301 WEIGHTPLATEBUSHING 10CT. 3 4 18 6189501 9 3117401 C~ PLUG WEIGHTSTAC
Summary of the content on the page No. 4
PLATE CABLE FIGURE 3 STEP 3 ¯ Unscrew the threaded ends of the HEAD PLATE CABLE from the WEIGHT STACK SHAFT & the D-RING and remove HEAD PLATE CABLE. The HEAD PLATE CABLE will be used later. See FIGURE 3. (NOTE: Remove pulleys for ease of removal.)
Summary of the content on the page No. 5
PRESS TENSION CORD t COTTERPIN~ i KEYI-IOLE CLEVIS,,~~ PRESS C LAT CABLE (67249) (667248) LEG CURL/EXTENSION CABLE (67247) FIGURE 4 STEP 4 ¯ CAREFULLY remove the PRESS TENSION CORD and PRESS CABLE by pulling the COTTER PIN and CLEVIS PIN from the KEYHOLE CLEVIS as shown in FIGURE 4. ¯ CAREFULLY remove the 1/4" CAP NUT for the PRESS TENSION CORD on the TOP BOOM. ¯ P/ease d/scm’d the previously removed PRESS TENSION CORD, PRESS CABLE, COTTER PIN, CLEVIS PIN, and KEYHOLE CLEVIS. 1/2 1~ 1/~: [ lt~ [
Summary of the content on the page No. 6
FIGURE 5 (67249) PRESS CABLE (67249) STEP 5 ¯ Carefully remove and discard the PRESS CABLE as shown in FIGURE 5. ~3/8" LOCK NUT ~3/8 X 2-1/4" BOLT 3-1/2" P~LEY ~ FIGURE 6 Remove the existing 3-1/2" PULLEY, 3/8 X 2-1/4" BOLT, 3/8" WASHERS, and 3/8" LOCK NUTS from the TOP BOOM. They will be used later. See FIGURE 6..
Summary of the content on the page No. 7
" ~" "-. ~ ~ TOP BOOM @ ~ 318 X 2-3/4" FIGURE 7 STEP 7 ¯ LOOSELY assemble one 4-1/2" PULLEY (6) to the TOP BOOM using one 3/8 X 2-3/4" BOLT (13), two 3/8" FLANGE SPACERS (12), and one 3/8" LOCK NUT (11). See FIGURE 3/8" LOCK NUT 3/8" WASHER ~,/ ~3/8 X 2-1/4" BOLT ~ 3-I/2" PULLEY FIGURE 8 STEP $ ¯ LOOSELY assemble the previously removed 3-1/2" PULLEY to the TOP BOOM (17) using the previou.,;ly removed 3/8 X 2-1/4" BOLT, two 3/8" WASHERS, and one 3/8" LOCKNUT. See FIGURE 8. 2 3 4 $ 6 I Oi I ,,! 1
Summary of the content on the page No. 8
FIGURE 9 PRESS-STACK CABLE (67475) PRESS-STACK CABLE (67475) STEP 10 ¯ Route the PRESS-STACK CABLE (5) around the pulleys and 1-brackets as shown in STEP 9, (Remove pulleys for ease instal- lationo) STEP 10 FIGURE 10 ¯ To assemble the PRESS-STACK CABLE (5) follow the cable routing as shown and use the following steps: ¯ Route the thread end of PRESS-STACK CABLE (5) up and over the PULLEY in the TOP BOOM above the WEIGHT STACK. (Remove pulley for ease of installation.) ¯ Screw the threaded end of
Summary of the content on the page No. 9
STEP 12 ¯ Insert two WEIGHT PLATE BUSHINGS (17) into the "PARABODY" side of each of the f’tfteen WEIGHT PLATES (16) as shownin FIGURE 11. FIGURE 11 FIGURE 12 BOOM ¯ ---- LOOSEN STEP 12 LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUq~DE RODS (1). See FIGURE 12. 4 J I I5 Lll 6 3 o J I I J I I I I 9
Summary of the content on the page No. 10
X 1-114" BASE FIGURE 13 ;TEP 13 ¯ Insert four CAP PLUGS (9) into the top and bottom ends of the GUIDE RODS (1) as shown in FIGURE13. ¯ SECURELY assemble the WEIGHT STACK SHAFT (2) to the I-[EAD PLATE (4) using one 3/8 X 1-1/4" BOLT (14) and one WASHER (10). ¯ Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 13. (NOTE: Lubricate GUIDE RODS (1) with silicon teflon spray available at most hardware stores.) o Slide two 1-1/4 SQ. X 4-7/8" TUBES (3), two 3/4" WASHERS (15), and two WEIGHT
Summary of the content on the page No. 11
(NOTE: Make; sure LAT CABLE runs over top of bolts in TOP BOOM.) FIGURE 14 STEP 14 ¯ CAREFULLY lift ortilt the TOP BOOM and insert all GUIDE RODS into the bushings. See FIGURE 14. ¯ With the GLT[DE RODS (1) securely held in the TOP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sure the CABLE runs over the top of the bolts in the TOP BOOM.) 6 0 I I l I I I II
Summary of the content on the page No. 12
FIGURE 15 ~) STEP 15 HEAD PLATE ¯ Screw one of the threaded ends of the previously CABLE removed HEAD PLATE CABLE approximately I" (67250) into the end of the WEIGHT STACK SHAFT. See FIGURE 15. STEP 16 ¯ Route the thread end of HEAD PLATE CABLE up and over the PULLEYS in the TOP BOOM above the WEIGHT STACK. (Remove pulleys for case of installation.) ¯ Screw the other threaded end of the HEAD PLATE CABLE approximately I" into the end of the shaft on the D-RING. Scc FIGURE 16. ¯ SECURELY tighten t
Summary of the content on the page No. 13
FIGURE 17 STEP 17 If the 435103 LEG PRESS ADAPTER KIT is not installed the rear SHROUD opening must be removed. AI~ply pressure to the bottom of the SHROUD where the "V" groove is and carefuly remove the weight stack opening on the plastic SHROUD as show~. " in FIGURE 17. 1/2 1/2 [ 1/2 [ [ 1r2 [ 1/2" [ 1/2 [ 6 4 5 1 I,, [ ! ! I I I I [ I I ! I I ! . I ! !
Summary of the content on the page No. 14
FIGURE 18 3/8" X 1" BUTI’ON HEAD CAP SCREW FRONT STEP 18 ¯ SECURELY attach the four previously removed 3/8" X 1" BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 18. AD C’ BUTTON FIGURE 19 ;TEP 19 ¯ SECURELY attach the four previously removed 3/8" X 1" BUTTON HEAD CAP SCREWS from the bottom of the from SHROUD & rear SHROUD. Remove the SHROUDS from the 425103 HOME GYM. See FIGURE 19. ¯ The PRESS STATION and SWIVEL LOW PULLEY are now operated with the front stack a
