Summary of the content on the page No. 1
M1107C
ITEM NUMBER: 1107
SERIAL NUMBER: _____________________
Owner’s Manual
Instructions for Assembly, Testing, Operation, Servicing, &
Storage
20 Ton Log Splitter: Outdoor hydraulic powered machine that
splits wood logs.
WARNING
READ and UNDERSTAND this manual completely before using log splitter.
All operators of this equipment must read and completely understand all safety information, operating instructions,
maintenance and storage instructions. Failure to properly operate and maintain the
Summary of the content on the page No. 2
Hazard Signal Word Definitions 2
Summary of the content on the page No. 3
Table of Contents About Your Log Splitter………………………………………………………………………………...4 Safety label Locations……………………………………………………………………………….….5 Machine Components Identification…………………………………………………...………………..7 Initial Unpacking & Set-up……………………………………………………………………….…….8 Moving & Towing to the Job Site…………………………………………………………………………. …..10 Before Each Use: Step One: Inspection/Maintenance…………………………………………………………………….. ….13 Step Two: Refueling……………………………………………………………………………………. …15 Step Three: Work site Selection & Se
Summary of the content on the page No. 4
About Your Log Splitter Thank you for purchasing your Northstar log splitter! About Your Log Splitter: This log splitter is a machine designed to split wood logs using a hydraulically powered moving wedge. The log splitter’s gasoline engine is used to pressurize the hydraulic system. This log splitter is designed to split logs up to 24” long, lengthwise with the grain only. Your splitter can be used in either a vertical or horizontal splitting position: When the splitter is set up to operate i
Summary of the content on the page No. 5
Safety Label Locations 4 6 3 1 2 8 7 5 FIG. 2262 Reference Part Number Description number 1 777886 Splitter Warning Decal 2 39260 Hot Muffler Decal 3 39259 Waning Decal 4 777891 Hydraulic Fluid Warning Decal 5 777892 Moving/Towing Decal 6 777890 Fire Hazard Warning Decal 7 777887 Splitter Operating Instruction Decal 8 777889 Stuck Log Warning Decal Always make sure safety labels are in good condition. If a safety label is missing or not legible, order new labels or unsafe operation could result.
Summary of the content on the page No. 6
Safety Label Locations 6
Summary of the content on the page No. 7
Machine Component Identification Ref Description Ref Description 1 2” Ball Coupler 10 Beam 2 Horizontal Lock 11 Endplate 3 Lifting Handle 12 Support Leg 4 Cylinder 13 Engine 5 Hydraulic Oil Fill Cap 14 Hydraulic Tank 6 Split Control Lever 15 Suction Strainer 7 Control Valve 16 Pump 8 Wedge 17 Towbar Leg 9 Log Cradle 18 Safety Chains 7
Summary of the content on the page No. 8
Initial Unpacking & Set-Up IMPORTANT! Engine is shipped without oil. DO NOT start the engine before adding oil. Step One: Add oil to the engine. Using a funnel. Add SAE 30 oil up to the FULL mark on the dipstick. (See engine Owner’s Manual for oil capacity and location of fill Add oil cap.) Step Two: Secure Split Control Lever to Control Valve. Use following procedures : Secure Split Control 1. Split Control Lever is shipped taped to the hydraulic cylinder. Untape to Lever release. 2. Raise leve
Summary of the content on the page No. 9
Initial Unpacking & Set-Up WARNING: NEVER remove the hydraulic oil fill cap when the engine is running or hot. Hot oil can escape causing severe burns. Allow log splitter to cool completely before removing hydraulic oil fill cap. 2. If hydraulic oil level is low: Add 10 wt. AW32, ASLE H-150, or ISO 32 oil to 1” from top. Note: The log splitter comes filled with LIGHT 150-ISO 32 hydraulic oil. If the log splitter will be run for long periods of time in outdoor temperatures above 70 F, we recomme
Summary of the content on the page No. 10
Moving and Towing to Job Site WARNING The log splitter is heavy. It can crush and cause serious injury if it rolls out of control or tips over. Follow the instructions below for safely moving and towing the log splitter. Moving the log splitter: 1. Place in Make sure the log splitter is secure in the horizontal position with hitch pin before Horizontal moving. position NEVER move log splitter when it is in vertical configuration because it will be unstable and could tip. 2. Engine off. IMPORTANT
Summary of the content on the page No. 11
Moving and Towing to Job Site Towing: 1. Read Review towing safety instructions in your vehicle manual. instructions 2. Check tires Make sure tires are fully inflated and in good repair. WARNING: Do not over-inflate tires. Serious injury can occur if tire explodes. When seating a bead after repair, do not exceed 30 PSI. Pressures higher than 30 PSI can cause the tire and wheel to rupture and explode. 3. Attach to hitch Attach log splitter to vehicle hitch (2” ball) 1) Attach log splitter’s c
Summary of the content on the page No. 12
Moving and Towing to Job Site 5. Put tow bar leg Move the tow bar leg to the “UP” position and lock. (The support leg must UP remain in the up position during towing.) Tow log splitter carefully to desired work site. 6. Tow to desired (See “Before Each Use” section for instructions on selecting an appropriate work site) location Important safety instructions: Added length. Be aware of the added length of the splitter. Speed limit. Never tow this log splitter over 45 mph. Faster speeds may re
Summary of the content on the page No. 13
Before Each Use-Inspection / Maintenance Step One: Inspect and maintain log splitter before each use If the log splitter has been used previously, it must be inspected and maintained BEFORE EACH SUBSEQUENT USE. WARNING ALWAYS shut off the engine, disconnect the spark plug, and relieve system pressure before inspecting, cleaning, adjusting, or repairing the splitter. Relieve system pressure by moving Split Control Lever back and forth several times. IMPORTANT: If a part needs replacement, only us
Summary of the content on the page No. 14
Before Each Use-Inspection / Maintenance should be heeded at all times when inspecting or servicing the hydraulic components of the log splitter: Stop the engine, disconnect the spark plug, and move all control valve handles back and forth to relieve pressure before changing or adjusting hydraulic system components such as hoses, tubing, fittings or other components. NEVER check for leaks with your hand. Leaks can be located by holding a piece of cardboard or wood (at least two feet long) wi
Summary of the content on the page No. 15
Before Each Use – Fueling Step Two: Fueling WARNING Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Use extreme care when handling gasoline. 1. Engine off / cool The engine must be off and allowed to cool at least two minutes before adding fuel. WARNING: A running engine is hot enough to ignite fuel. Never add fuel or remove gas cap if engine is running or still hot. 2. Outdoor location Fill fuel tank outdoors – never indoors. WARNING: Gasol
Summary of the content on the page No. 16
Before Each Use – Work Site Selection & Set-Up Step Three: Work site selection and log splitter set-up WARNING It is important to select an appropriate work site and properly set up the log splitter in order to minimize the risk of slips and falls, equipment rolling or tipping over, carbon monoxide poisoning, and accidental fires. 1. Select location Select an appropriate location for operating the log splitter. Requirements: 1. Dry-level surface with good footing. Stay clear of areas with mud, i
Summary of the content on the page No. 17
Before Each Use – Work Site Selection & Set-Up 4. Lock both legs Lock both the support leg and the tow bar leg in the “DOWN” position. DOWN 5. Block wheels Block the wheels to prevent unintended movement of the log splitter. 17
Summary of the content on the page No. 18
Splitting Operation WARNING Before starting this log splitter, review the following instructions and safety information for safe operation of the log splitter. Failure to follow these rules may result in serious injury to the operator or bystanders from moving parts that crush, cut, or entangle, from flying objects, burns, fire, falling or tripping, or from carbon monoxide poisoning. General safety information: Read manual. Do not allow anyone to operate the log splitter who has not read the O
Summary of the content on the page No. 19
Splitting Operation 1. Put on Wear the following protective clothing and safety gear: protective 1) Eye protection. Always wear safety glasses or goggles when operating the clothing / gear machine. Pieces of log may fly out and serious eye injury can occur. 2) Boots. Falling logs can crush feet. Always wear safety shoes or heavy boots when operating or helping to load logs. 3) Gloves. Wear snug fitting gloves without draw strings or loose cuffs. 4) Hearing protection. The use of ear plugs or oth
Summary of the content on the page No. 20
Splitting Operation 1) Remove horizontal lock pin, grasp lifting handle and lift beam until it rotates into b) Set to Vertical vertical position. position WARNING: Crush hazard. The beam is heavy – do not let it just drop. It could crush fingers or cause damage to the splitter. VERTICAL SPLITTING POSITION 2) To return to horizontal position, grasp lifting handle and lower beam carefully in a controlled manner until it rests in the horizontal position, insert horizontal lock pin. 4. Start engine
