Summary of the content on the page No. 1
1695539 Dual Stage Snowthro wer, 8.0 Torque Power, 24 Inch
1742237
Revision 00
Rev. Date 7/2008
TP 199-4955-00-LW-R
Summary of the content on the page No. 2
1 1 5 14 9 13 10 2 11 6 3 8 12 4 21 15 19 7 21 1742237 2
Summary of the content on the page No. 3
en CONTENTS HAZARD SYMBOLS AND THEIR MEANINGS . . . . . . . . . . . . 4 OPERATING SYMBOLS AND THEIR MEANINGS . . . . . . . . . 4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 MAINTENANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 TROU
Summary of the content on the page No. 4
en Forward Oil Safety Alert − Identifies safety information about hazards that can result in personal injury. Neutral Fuel Operator’s Manual − Read and understand Reverse before performing any activity or running On Off equipment. Ignition On Rotating auger Primer bulb Fire Ignition Off Throttle Rotating impeller Ignition Key Explosion Choke off Push to engage Toxic fumes electric start Choke on Shock Electric Stop Rotating gears Start Hot Surface Slow Engine Thrown objects Start Fast Engine Run
Summary of the content on the page No. 5
en Stop engine and remove keys when performing maintenance on equipment. 1742237 5
Summary of the content on the page No. 6
en 1742237 6
Summary of the content on the page No. 7
en RULES FOR SAFE OPERATION WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. Safe Operation Practices for Snowthrowers 8. Let engine (motor) and snowthrower adjust t
Summary of the content on the page No. 8
en 18.Never direct discharge at bystanders or allow anyone in front of the unit. 2. Never store the machine with fuel in the tank inside a building where ignition sources are present such as hot water and space heaters, or 19.Never leave a running unit unattended. Always disengage the auger and clothes dryers. Allow the engine to cool before storing in any enclosure. traction controls, stop engine, and remove keys. 3. Always refer to operator’s manual for important details if the 20.Do not opera
Summary of the content on the page No. 9
en 5. Install the fasteners and the crank assembly ASSEMBLY How To Assemble The Drift Cutter eyebolt (11) that were removed in step 2. (if equipped) DO NOT tighten until all fasteners are in Read and follow the assembly and adjustment Drift cutters are used to cut a path through snow place. instructions for your snow thrower. All fasteners deeper than the auger housing. are in the parts bag. Do not discard any parts or 6. (Figure 5) Attach the crank rod (15) to the 1. (Figure 11) Loosen the fast
Summary of the content on the page No. 10
en 4. Push the stop switch (13) to the ON How To Stop The Snow Thrower Before Starting The Engine position. (Figure 1) 1. Before you service or start the engine, 5. Push in the safety key (8). 1. To stop discharging snow, release the auger familiarize yourself with the snow thrower. Be sure you understand the function and drive lever (5). 6. Rotate the choke knob (14) to the CHOKE location of all controls. position. 2. To stop the wheels, release the traction 2. Check the tension of the clutch c
Summary of the content on the page No. 11
en Warm engines will cause condensation in cold (Figure 21) On some models, a clean−out tool 3. For complete snow removal, slightly overlap weather. To prevent possible freeze−up of recoil (1) is attached to the top of the auger housing. each previous path. starter and engine controls, proceed as follows Use the clean−out tool (1) to remove snow 4. Whenever possible, discharge the snow after each snow removal job. from the auger housing. down wind. 1. Run the snow thrower a few minutes after 1.
Summary of the content on the page No. 12
en As Required 3. The auger gear case is lubricated at the How To Check And Adjust The Cables factory and does not require additional The traction drive cable and the auger drive The following adjustment should be preformed lubrication. If for some reason the lubricant cable are adjusted at the factory. During normal more than once each season. leaks out, have the auger gear case checked use, a cable can become stretched and must be 1. Adjust the auger drive belt after the first 2 to by a factor
Summary of the content on the page No. 13
en 11. (Figure 15) To check the adjustment, 3. Remove the bottom panel (2). 7. Make sure the traction drive idler pulley depress the drive lever and check the length (12) is properly aligned with the traction 4. (Figure 18) Remove screw (2) from belt “A” of the drive spring (7). In correct drive belt (13). cover (1). Remove the belt cover (1). adjustment, the length “A” of the drive 8. Attach the traction drive spring (16). 5. (Figure 19) Loosen the belt guide (9). Pull spring (7) is as follows:
Summary of the content on the page No. 14
en 6. (Figure 25) Note the position of the friction 13.(Figure 32) Install the hex shaft (8) and 1. Drain the fuel tank. wheel (4). The correct distance “A” from the bearings (7) with the four bolts removed 2. Let the engine run until it is out of gasoline. earlier. right side of the friction wheel (4) to the 3. Never store the snow thrower with fuel in the outside of the motorbox is as follows: Make sure the washers (17) are properly tank inside a building where ignition sources Tire Size Dista
Summary of the content on the page No. 15
en TROUBLE SHOOTING CHART TROUBLE CAUSE CORRECTION Difficult starting Defective spark plug. Replace spark plug. Water or dirt in fuel system. Use carburetor bowl drain to flush and refill with fresh fuel. Engine runs erratic Blocked fuel line, empty gas tank, or stale Clean fuel line; check fuel supply; add fresh gasoline. gasoline. Engine stalls Unit running on CHOKE. Set choke lever to RUN position. Engine runs erratic; Water or dirt in fuel system. Use carburetor bowl drain to flush and refil
Summary of the content on the page No. 16
en BRIGGS AND STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY Effective January 1, 2008 replaces all undated Warranties and all Warranties dated before January 1, 2008 LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the product that is defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is eff
Summary of the content on the page No. 17
fr TABLE DES MATIÈRES SYMBOLES DE DANGERS ET LEURS SIGNIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SYMBOLES DE DANGERS ET LEURS SIGNIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 MONTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 FONCTIONNEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 TABLEAU DE MAINTENANCE . . . . . . . . . . . . . . .
Summary of the content on the page No. 18
fr Contact activé Contact désactivé Clé de contact Appuyer pour engager le démarreur électrique Démarreur électrique Démarrage du moteur Moteur en Engager marche Moteur à Traction l’arrêt Collecteur de la fraise Embrayage de la fraise Embrayage de traction Engager Désengager Déversoir Déflecteur GAUCHE BAS DROIT HAUT 1742237 18
Summary of the content on the page No. 19
fr 1742237 19
Summary of the content on the page No. 20
fr 1742237 20
