Summary of the content on the page No. 1
OperatiOn and parts Manual
MOdels
ar13Ha
ar13Har
ride-On tandeM druM rOller
series drive systeM
(HOnda GX630rQZB2 GasOline enGine)
Serial No. 110301 and ABOVE
Revision #0 (06/22/11)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Summary of the content on the page No. 2
prOO p sitiOn 65 warninG page 2 — aR13Ha/aR13HaR ROLLeR (s/n 110301 & up) • O peRa TiOn anD paRTs manuaL — Rev. #0 (06/22/11)
Summary of the content on the page No. 3
t aBle Of COntents drawings ar13Ha/Har ride-On Explanation Of Code In Remarks Column............. 42 t andem roller Suggested Spare Parts ......................................... 43 Proposition 65 Warning ........................................... 2 Nameplate And Decals ..................................... 44-47 Table Of Contents .................................................... 3 Front Drum Assy. .............................................. 48-49 Safety Information ....................
Summary of the content on the page No. 4
safety infOrMatiOn Do not operate or service the equipment before reading The following table shows the potential hazards associated the entire manual. Safety precautions should be followed with the operation of this equipment. at all times when operating this equipment. Failure to read and understand the safety Symbol Safety Hazard messages and operating instructions could result in injury to yourself and others. Lethal exhaust gas hazards saFeTY messages The four safety messages shown belo
Summary of the content on the page No. 5
safety infOrMatiOn geneRaL saFeTY NOTICE CauTiOn This equipment should only be operated by trained and qualifi ed personnel 18 years of age and older. neveR operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, Whenever necessary, replace nameplate, operation and hearing protection, steel-toed boots and other protective safety decals when they become diffi cult read. devices required by the job or city and state regulations. Manu
Summary of the content on the page No. 6
safety infOrMatiOn ROLLeR saFeTY DO nOT use worn-out hoses or couplings. Inspect daily. aLWaYs store equipment properly when it is not being DangeR used. Equipment should be stored in a clean, dry location neveR operate the equipment in an explosive out of the reach of children and unauthorized personnel. atmosphere or near combustible materials. An explosion or fi re could result causing severe engine saFeTY bodily harm or even death. DangeR WaRning The engine fuel exhaust gas
Summary of the content on the page No. 7
safety infOrMatiOn or hot. NOTICE DO nOT overfi ll tank, since spilled fuel could ignite if it neveR run engine without an air fi lter or with a dirty air comes into contact with hot engine parts or sparks from fi lter. Severe engine damage may occur. Service air fi lter the ignition system. frequently to prevent engine malfunction. Store fuel in appropriate containers, in well-ventilated neveR tamper with the factory settings areas and away from sparks and fl ames. of the engin
Summary of the content on the page No. 8
safety infOrMatiOn rinse skin or clothing immediately with plenty of water. transporting on a trailer. Make sure all supports attaching the roller to the trailer are tight. If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty enviROnmenTaL saFeTY of water and contact the nearest doctor or hospital to NOTICE seek medical attention. Dispose of hazardous waste properly. CauTiOn Examples of potentially hazardous waste aLWaYs di
Summary of the content on the page No. 9
speCifiCatiOns Table 1. specifications (Roller) Shipping Weight 2,572 lbs. (1,167 Kg.) Dry Weight 2,428 lbs. (1101 Kg.) Operating Weight 3,088 lbs. (1,400 Kg.) Operating Weight w/ Drum Ballast 3173 lbs. (1,439 Kg.) Overall Length 85 in. (2,159 mm.) Overall Width 38.25 in. (972 mm.) Overall Height-ROPS (up) 88 in.(2235 mm.) Maximum Rolling Width 35.7 in. (907 cm.) Turning Radius-Inside 109 in. (2,768 mm.) Ground Clearance 11.5 in. (292 mm.) Curb Clearance 7.75L, 19.0R (197 mm., 483 mm.) Wall Clea
Summary of the content on the page No. 10
speCifiCatiOns Table 2. specifications (engine) Model Honda GX630RQZB2 Engine Air-Cooled 4 Stroke, Overhead Valve, 2 cylinders Type (90 degree V-Twin), Gasoline Engine. Piston Displacement 37.5 cu. in. (614 cc) [Bore x Stroke] [3.03 in. x 2.60 in. (77 mm x 66 mm)] Max. Output 20 hp (13.4 KW, 18.3 PS) at 3,600 rpm Max. Governed Speed, No Load 3,500 rpm Max. Torque 31.8 lbf-ft. at 2,500 rpm Cooling System Forced Air Engine Oil SAE-10W-30 for general use Engine Oil Capacity (with oil filter replac
Summary of the content on the page No. 11
diMensiOns Figure 1. Roller Dimensions Table 3. Dimensions (Roller) Wheelbase A 45.0 in. (1,143 mm.) Drum Diameter B 22.6 in. (574 mm.) Curb Clearance C 7.75 in. Left, 19.0 in. Right ( 197 mm., 483 mm.) Drum Width D 35.7 in. (907 mm.) Overall Height (with ROPS) E 88 in. (2,235 mm.) Ground Clearance F 11.5 in. (292 mm.) Overall Length G 85 in. (2,159 mm.) Wall Clearance H 1.75 in. Left, 1.25 in. Right ( 45 mm., 32 mm.) Drum Thickness I .38 in. (10 mm.) Overall Width J 38.25 in. (972 mm.) Seat Hei
Summary of the content on the page No. 12
General infOrMatiOn The AR13HA/HAR roller has been designed for asphalt action generates 3,100 lbs. (1,406 Kg.) of centrifugal force application and compaction of granular soils used in at a frequency of 4,000 vpm (vibrations per minute). If the site preparation. Use the machine only for the purpose vibration appears to be weak or slow, allow the machine to intended and by experienced personnel who understand warm-up thoroughly, and check the hydraulic oil level. Add this operation manual an
Summary of the content on the page No. 13
REAR ROLLER General infOrMatiOn Tipping (R OLLOveRs) DangeR DO NOT allow personnel to stand under or near any CauTiOn suspended machine. Before operating the roller, make neveR operate the roller on side slopes (Figure 3). The sure that personnel and obstacles are free from the possibility exists that the roller could tip over (roll over), thus roller’s path. Serious injury or death may result. causing bodily harm, even death, and serious damage to the equipment. The forward-reverse co
Summary of the content on the page No. 14
COMpOnents 18 19 17 20 21 22 12 13 14 23 16 24 15 25 11 9 10 4 8 5 7 3 6 1 2 Figure 4. Roller Components page 14 — aR13Ha/aR13HaR ROLLeR (s/n 110301 & up) • OpeRa TiOn anD paRTs manuaL — Rev. #0 (06/22/11)
Summary of the content on the page No. 15
COMO p nents Figure 4 shows the location of the components and basic return this valve to the closed position (clockwise) when components for the AR13HA compaction roller. The function water is not required. of each component or control is described below: 13. Throttle Control — Pull all the way out to achieved maximum engine RPM's. To idle the engine, push the 1. Battery — Provides +12VDC to the electrical system, and is located underneath foot plate. Replace only with RED stop button inwar
Summary of the content on the page No. 16
COMO p nents 40 42 38 41 37 36 35 30 29 34 33 26 28 39 27 Figure 5. Additional Roller Components 32 31 Figure 5 shows the location of additional components for the AR13HA compaction roller. The function of each component or control is described below: 34. steering Cylinder — Controls direction of roller. 26. Front sprinkler system — A gravity feed spray bar is 35. engine — This unit incorporates a HONDA GX630, air provided for the wetting the roll for asphalt pavement. cooled engine rated
Summary of the content on the page No. 17
BasiC enGine Figure 6. Engine Components The engine (Figure 6) must be checked for proper 5. Fuel Filter — Prevents dirt and other debris from lubrication and filled with fuel prior to operation. Refer to the entering the fuel system. manufacturer's engine manual for operation and servicing 6. a ir Filter — Prevents dirt and other debris from information. entering the fuel system. Unsnap air filter cover to gain 1. Oil Drain plug — Remove to drain crankcase oil. Fill access to filter elem
Summary of the content on the page No. 18
inspeCtiOn 3. Check the oil level shown on the dipstick (Figure 8). BeFORe sT aRTing 1. Read safety instructions at beginning of manual. 2. Clean the roller, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one. 4. Check carburetor for external dirt and dust. Clean with dry compressed air. 5. Check fastening nuts and bolts for tightness. engine OiL CH
Summary of the content on the page No. 19
inspeCtiOn 5. Pay attention to the fuel tank capacity when replenishing FueL CHeCK fuel (Figure 12). Refer to the fuel tank capacity listed DangeR on the specifications table. Motor fuels are highly flammable and can be dangerous if mishandled. DO nOT smoke while refueling. DO nOT attempt to refuel the pump if the engine is hot or running. 1. To check the engine fuel level, place the roller on secure level ground with the engine stopped. 2. Tilt the operator's seat (Figure 10) forward
Summary of the content on the page No. 20
inspeCtiOn 3. If the hydraulic oil level is low, remove the hydraulic BaTTeRY CHeCK oil cap (Figure 14) and fill with type ISO 46 anti-wear A 12-volt DC battery (Figure 16) is shipped dry, and will type hydraulic oil to the recommended operating level. require a proper electrolyte level for operation. ALWAYS be sure that the battery cables are properly connected to the battery terminals as shown below. Generally the RED cable will be connected to the positive terminal of the battery, an
