MTD E614E user manual

User manual for the device MTD E614E

Device: MTD E614E
Category: Snow Blower
Manufacturer: MTD
Size: 5.86 MB
Added : 9/21/2014
Number of pages: 28
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for MTD E614E. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with MTD E614E.

For your convenience

If looking through the MTD E614E user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual MTD E614E on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual MTD E614E to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
MTD E614E User manual - Online PDF
Advertisement
« Page 1 of 28 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual MTD E614E but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to MTD E614E. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

OPERATOR’S MANUAL
Model Numbers
E642E, E662H,
614E, E644E,
E664F
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
Warning:
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the oper

Summary of the content on the page No. 2

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL-HEED ITS WARNING. : WARNING The Engine Exhaust from this product contains chemica

Summary of the content on the page No. 3

• If the snow thrower should start to vibrate • Never operate the machine at high transport abnormally, stop the engine and check speeds on slippery surfaces. Look behind and use immediately for the cause. Vibration is generally a care when backing. warning of trouble. • Never direct discharge at bystanders or allow • Stop engine whenever you leave the operating anyone in front of unit. position, before unclogging the collector/impeller • Disengage power to collector/impeller when housi

Summary of the content on the page No. 4

SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says. Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in this Operator’s Manual. The information on the model plate is very important if you need help from your dealer or the MTD customer support de

Summary of the content on the page No. 5

SECTION 4: CONTENTS OF HARDWARE PACK Lay out the hardware according to the illustration for identification purposes. Parts are illustrated approximately one-half size. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not used on your unit.) ATTACHING THE HANDLE ASSEMBLY ATTACHING THE CHUTE ASSEMBLY A B Hex Bolts Hex Bolts 1/4-20 x 3/4" Long 5/16-18 x 1-3/4" Long (710-3015) (710-3180) Hex Bolts Hex Lock Nuts 5/16-18 x 3/4" Long 1/4-20 Threa

Summary of the content on the page No. 6

SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service engine Attaching the Handle Assembly. with gasoline, and check oil level as instructed in the (Hardware A and E) separate engine manual packed with your unit. Lay loose parts out on flat surface. Control NOTE: All references to right or left side of the 1. Handle Panel 5. Traction Drive Grip snow thrower are determined from behind the unit 2. Right Handle in the operating position. 6. Right Gri

Summary of the content on the page No. 7

3. Insert curved end of the Z fitting into the top 5. Secure with hex bolt, spacer and lock nut. See hole in the triangular metal tab on the auger Figure 6. (Do not overtighten this bolt as it will control grip. See Figure 5. prevent the grips from automatically returning to their upright position.) 6. Repeat process for the right side Traction Drive Control Grip. Triangle Metal Tab 7. Lay handle assembly behind snow thrower. See Figure 7. Auger Control Grip Hex Bolt (5/16-18 x

Summary of the content on the page No. 8

Traction Shift Drive Lever Clutch Ferrule Flat Washer Hairpin Shift Clip Rod Flat Washer Hairpin Shift Clip Arm Assembly Figure 9 Figure 11 Flat Washer Lock Washers Shift Hairpin Lever Clip Cable Roller Hex Bolt Handle Guide Ferrule 3/4” Long Tab Shift Hex Rod Bolt 1-3/4” Long Flat Washer Figure 10 Hairpin Shift Clip Arm ATTACHING SHIFT ROD Assembly (Hardware D) 1. Place the shift lever in the fifth (5) or the fastest Figure 12 forward speed position. 3. Models 642, 662

Summary of the content on the page No. 9

ATTACHING CLUTCH CABLES 1. Thread the hex jam nuts all the way up the Chute Assembly threaded portion of the “Z” ends. 2. Make certain all cables are in the grooves of the Hex Bolt cable roller guides. The roller guides are located in the lower rear of the unit. Lift the clutch grip in the raised (up) position. 3. Thread the cable onto the threaded portion of the “Z” end until there is no slack in the cable, but the cable is NOT tight. Do not overtighten cable. See Figure 13. Hex

Summary of the content on the page No. 10

4. Place one flat washer on the end of the chute FINAL ADJUSTMENTS crank, then insert the end of the crank into the hole in the plastic bushing in the chute crank Auger Drive Clutch bracket. See Figure 17. 1. To check the adjustment of the auger drive clutch, push forward on the left hand clutch grip Flat Washer Chute Crank depressing the rubber bumper under the clutch grip (See part #13 on page 22). There should be slack in the cable. 2. Release the clutch grip. The cable should

Summary of the content on the page No. 11

Adjusting The Skid Shoes The space between the shave plate and the ground can be adjusted by adjusting the skid shoes. 1. Place skid shoes in the low position to remove snow close to the ground. Place skid shoes in a higher position to remove snow from uneven ground. See Figure 19. Low Position 2. Adjust skid shoes by loosening the four hex High Position nuts and carriage bolts and moving skid shoes Hex Nuts Skid to desired position. Make certain the entire Carriage

Summary of the content on the page No. 12

Auger Auger Traction Drive Drive Drive Traction Clutch Clutch Clutch Drive Clutch Shift Shift Chute Lever Lever Chute Crank Crank Figure 22 Figure 23 SECTION 7: OPERATION BEFORE STARTING WARNING: Observe all Warning Metal Loop Labels on the snow thrower prior to on Spark use. See Figure 1. Plug Wire Rubber Boot Your snow thrower is shipped with oil; however, you must check the oil level before operating. Figure 24 Be careful not to overfill. 3. Make certain the auger and drive clutch lev

Summary of the content on the page No. 13

Follow all instructions carefully. Determine that your 4. Push primer button two or three times. Refer to house wiring is a three wire grounded system. Ask a Figure 21 on page 11. If engine is warm, push licensed electrician if you are not certain. If your primer button once only. house wiring system is not a three-wire grounded NOTE: Always cover vent hole in primer button system, do not use this electric starter under any when pushing. Additional priming may be necessary conditions. If your sy

Summary of the content on the page No. 14

TO ENGAGE DRIVE/AUGER WARNING: Temperature of muffler and 1. With the engine running near top speed, move o surrounding areas may exceed 150 F. shift lever into one of the FORWARD or Avoid these areas. REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use the slower speeds until you are familiar • For most efficient snow removal, remove with the operation of the snow thrower. snow immediately after it falls. 2. Squeeze the left hand auger drive clutch to •Discharg

Summary of the content on the page No. 15

Model 614, 644, 664: 5. If adjustment is necessary, loosen the jam nut on the traction drive cable, and thread cable in 3. Push down on the shift arm assembly as far as or out as necessary. it will go. Thread the ferrule up or down the shift rod and align it with the hole closest to the shift 6. Tighten the jam nut to secure the cable when knob on the narrow side of the shift lever correct adjustment is reached. Reassemble the assembly behind the handle panel. frame cover with six self-tapping

Summary of the content on the page No. 16

SECTION 9: LUBRICATION WARNING: Disconnect the spark GEAR CASE plug wire and ground against the The gear case is lubricated with grease at the engine before performing any factory and does not require checking. If lubrication or maintenance. disassembled for any reason, lubricate with 2 ounces of Shell Alvania grease EPR00, part number ENGINE 737-0168. Before reassembling, remove old sealant Refer to engine manual for all engine lubrication and apply “Loctite 5699” or equivalent. instructions.

Summary of the content on the page No. 17

5. Roll the front and rear auger belts off the engine AUGER BELTS pulley. See Figure 30. NOTE: It is necessary to remove both belts in 6. Unhook the idler spring from the hex bolt on the order to change either one. If changing just one belt, auger housing. See Figure 31. be certain to check the condition of the other belt. 7. Back out the stop bolt to allow the belts to slip 1. Remove the plastic belt cover on the front of the between the bolt and auger pulley. engine by removing the two self-t

Summary of the content on the page No. 18

6. Lightly tap the hex nut to dislodge the ball Friction bearing from the right side of frame. Remove Wheel the hex nut and bell washer from left end of Friction Wheel Disc shaft. 7. Slide the gear shaft to the right and slide the Drive Belt friction wheel assembly from the shaft. 8. Remove the six screws from the friction wheel assembly (three from each side). Remove the Support Bracket friction wheel rubber from between the friction wheel plate. 9. Reassemble new friction wheel rubber to the

Summary of the content on the page No. 19

SECTION 12: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel. Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used. Blocked fuel line. Clean fuel line. Choke not in ON position Move switch to ON position Faulty spark plug. Clean, adjust gap or replace. Key not in switch on engine. Insert key. Spark plug wire Connect spark plug wire. disconnected. Primer button not depres

Summary of the content on the page No. 20

SECTION 13: ILLUSTRATED PARTS HOUSING ASSEMBLY 20


Alternative user manuals
# User manual Category Download
1 MTD 150 User manual Snow Blower 94
2 MTD 190-469A User manual Snow Blower 6
3 MTD 190-032-101 User manual Snow Blower 23
4 MTD 179cc User manual Snow Blower 21
5 MTD 200 User manual Snow Blower 12
6 MTD 199-658 User manual Snow Blower 1
7 MTD 191-768 User manual Snow Blower 1
8 MTD 235 User manual Snow Blower 2
9 MTD 190-768 User manual Snow Blower 0
10 MTD 208cc User manual Snow Blower 57
11 MTD 230, S230, 240, S240, 250, S250, 260, S260, 261, S261 User manual Snow Blower 5
12 MTD 230 User manual Snow Blower 0
13 MTD 240 User manual Snow Blower 16
14 MTD 250 User manual Snow Blower 8
15 MTD 285 User manual Snow Blower 0
16 Agri-Fab 45-0402 User manual Snow Blower 2
17 Agri-Fab 45-0418 ATV User manual Snow Blower 1
18 Agri-Fab 45-0418 User manual Snow Blower 1
19 Alliance Laundry Systems DRYING TUMBLERS 70269501R3 User manual Snow Blower 2
20 Ariens 924 SNO-THRO 924109 User manual Snow Blower 60