Summary of the content on the page No. 1
CR9932
3 Band Single Alarm
Night Light Clock Radio
Please read this manual before use
ROBERTS
Sound for Generations
Summary of the content on the page No. 2
Controls (Top) 3 4 5 2 6 1 12 11 10 9 8 7 (Left side) (Right side) 5. Waveband selector 9. Alarm/Off button 1. Dimmer switch 10. Time button 2. Function switch 6. Tuning control 7. Snooze/night light button 11. Minute button 3. Headphone socket 8. Sleep button 12. Hour button 4. Volume control 1
Summary of the content on the page No. 3
Controls (Front) 13 14 16 15 13. PM indicator 14. LED dial pointer 15. Battery compartment (underside) 16. Alarm indicator If you need any further advice, please call our Technical Helpline on :- 2 020 8758 0338 (Mon-Fri)
Summary of the content on the page No. 4
Switching on and setting the time Before using your clock radio you must first set the correct time. 1. Place the unit on a flat surface. Plug the power cord into the wall socket and switch on. 2. The clock display will flash 12:00. 3. Press and hold down the Time Set button. 4. Whilst holding down the Time Set button press the Hour, or Minute buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the
Summary of the content on the page No. 5
Listening to the Radio 1. Turn on the radio by sliding the Function switch to the 'On ' position. The LED dial pointer will light up indicating that the radio is switched on. 2. Select the required waveband using the Waveband selector switch. 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated by the LED dial pointer. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positi
Summary of the content on the page No. 6
Alarm The alarm can be set to wake you by either the buzzer or the radio. Setting alarm time 1. Press and hold down the Alarm/Off button. 2. Whilst holding down the Alarm/Off button press the Hour, or Minute buttons to set the time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Checking the alarm time 1. To check alarm time, press and hold down the Alarm/Off button the display w
Summary of the content on the page No. 7
Setting the alarm to wake to buzzer 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. The Alarm indicator will light. The alarm will sound every day at the preset time for 59 minutes. To turn off the alarm until the next day press the Alarm/Off button. To turn off the alarms permanently set the Function selector to the 'Off' position. Setting the alarms to wake to radio 1. Set the alarm time as previously described. Set the Function switch to the
Summary of the content on the page No. 8
Snooze control The radio or buzzer alarm can be silenced for 7 minutes by pressing the Snooze Light button. This sequence can be repeated whilst the alarm is sounding. Sleep timer The radio can be set to turn off after a preset time has elapsed. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elapsed. To cancel the sleep function before the preset time has expired, press the Alarm/Of
Summary of the content on the page No. 9
Headphones (on rear) A Headphone Socket (3.5mm) is provided for use with either headphones or an earpiece . Inserting a plug automatically mutes the internal loudspeaker. Night light Press the Snooze button once to turn on the night light. Press again to turn it off. The night-light will provide a warm glow adequate to allow movement around the room safely. It is not intended as a reading light. If you need any further advice, please call our Technical Helpline on :- 8 020 8758 0338 (Mon-Fri)
Summary of the content on the page No. 10
General Fuse Do not allow this unit to be exposed to water or steam. It is recommended This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug that the FM band be used wherever possible as better results in terms (BS1363). If another type of plug is used a 5A fuse should be fitted in of quality and freedom from interference will usually be obtained than the plug, adaptor or distribution board. on the MW or LW bands. IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN. Mains supply Back-up
Summary of the content on the page No. 11
Specifications Circuit Features Power Requirements Loudspeaker 75mm diameter 8 ohms Mains AC 230 volts, 50Hz only Output Power 0.3W RMS Back-up Battery IEC size 6LR61 (6F22,PP3) Aerial System FM Wire Aerial Frequency Coverage FM 87.5 - 108MHz MW Built-in Ferrite aerial MW 525 - 1610kHz LW 147 - 284kHz LW Built-in Ferrite aerial The Company reserves the right to amend the specification without notice. If you need any further a
Summary of the content on the page No. 12
Guarantee This radio is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Product with removed or defaced serial numbers. Procedure: Any claim under this guara
