Summary of the content on the page No. 1
Operating and installation instructions
Built-in plate warmer
EGW 602 - 14
To prevent accidents and
UV
machine damage, read
these instructions
before
installation or use. M.-Nr. 05 478 600
Summary of the content on the page No. 2
Contents Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Caring for our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Guide to the plate warmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using the plate warmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Controls . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Warning and Safety instructions Technical safety This appliance is intended for resi- Before installation make sure that dential use only. Only use the appli- the voltage and frequency listed on ance for its intended purpose. the data plate correspond with the household electrical supply. This data Improper use of the appliance can must correspond to prevent injury and lead to personal injury and material machine damage. Consult a qualified damage. The manufacturer cannot electrician if in doubt
Summary of the content on the page No. 4
Warning and Safety instructions Do not operate any appliance with Use a damaged cord or plug or after The temperature in the drawer can the appliance malfunctions or has been reach up to approx. 176 °F (80 °C) damaged in any manner. Return the ap- depending on the temperature selected pliance to the nearest authorized servi- and how long the appliance has been ce facility for service. on. Installation, repair and mainte- Do not touch hot surfaces. Use handles nance work should be by a Miele or k
Summary of the content on the page No. 5
Warning and Safety instructions General notes Disposal of an old appliance Children should not be left alone or Before discarding an old appli- unattended in an area where an ance, disconnect the power cord appliance is in use. They should never and remove any doors to prevent haz- be allowed to sit or stand on any part of ards. the appliance. Caution: Do not store items of interest to children in cabinets above or in the plate warmer. Children climbing on the appliance to reach these items coul
Summary of the content on the page No. 6
Caring for our environment Disposal of the packing Disposal of an old appliance material Old appliances contain materials which can be recycled. Please contact your The transport and protective packing local recycling center about potential materials are environmentally friendly recycling. for disposal and may be recyclable. Ensure that the appliance presents no Ensure that any plastic wrap is dis- danger to children while waiting for dis- posed of safely and kept out of the posal. See the instr
Summary of the content on the page No. 7
Guide to the plate warmer a On/Off button b Temperature control c Warming drawer d Non-slip mat e Rail f On/Off indicator light 7
Summary of the content on the page No. 8
Using the plate warmer The plate warmer is only intended for Controls warming dishes. Do not use the plate warmer to re-heat, cook or keep food or drinks warm. Condensation from food or drinks could cause moisture dam- age to the appliance. The appliance operates with a hot air system. A fan distributes hot air to heat plates quickly and evenly. A protective grill prevents any contact with the heating element and fan. The rail in the drawer separates the The controls consist of the temperature c
Summary of the content on the page No. 9
Using the plate warmer Warming dishes Procedure in brief: ^ Place the dishes in the warming drawer. ^ Select the desired temperature set- ting. ^ Turn on the appliance (j). ^ Close the drawer. The indicator on the front of the appli- ance lights up to show that the appli- ance is on. ^ Turn the appliance off (k), before re- moving warmed dishes. The following loading examples are given as a guide only. Loading the drawer 6 place settings: The quantity which can be loaded will 6 dinner plates (11
Summary of the content on the page No. 10
Using the plate warmer Selecting a temperature Warming times The temperature control is used to ad- Various factors will affect the warming just the temperature setting. times: – material and thickness of dishes, Only turn the temperature control clockwise and then back again. – quantity, Stop when you feel a resistance. – how dishes are arranged, Forcing the control past this point will damage it. – temperature setting. As you use the plate warmer you will The heat will shut off automatically l
Summary of the content on the page No. 11
Cleaning and care Mat with non-slip surface Never use abrasive cleaners, scour- The mat can be removed to clean the ing pads, steel wool or caustic bottom of the drawer. (oven) cleaners on the plate warmer. They will damage the surface. Clean the mat by hand with some hot water and liquid dish soap. Dry thor- oughly. Do not return the mat until it is Cleaning the exterior completely dry. The exterior of the plate warmer can be cleaned with warm water and liquid dish soap applied with a soft spon
Summary of the content on the page No. 12
Frequently asked questions nearest Miele Technical Service Depart- Installation, maintenance and repairs ment. to the electrical components of this appliance should only be by a quali- . . . dishes are not warm? fied technician in accordance with Check national and local safety regulations. – whether the noise of the fan can be Repairs and other work by unquali- heard. fied persons could be dangerous and may void the warranty. If the fan is running: the heating element is faulty. Some minor prob
Summary of the content on the page No. 13
After sales service In the event of a fault which you cannot correct yourself please contact: – Your Miele Dealer or – The Miele Technical Service Department USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting the Technical Service Department, please quote the model and serial number of your appliance both of which are shown on the data plate which is next to the control panel. 13
Summary of the content on the page No. 14
Electrical connection The electrical installation instructions Note to the installer for any appliance installed in combi- Please leave these instructions with nation with the plate warmer must be the consumer. observed. When another appliance is installed Power supply in combination with the plate warmer This appliance is equipped with an to the same circuit breaker, operat- approx. 6 ft (approx. 1.8 m) long power ing both appliances at the same cord with plug ready for connection to a time cou
Summary of the content on the page No. 15
Installation options The plate warmer may only be installed Steam oven beneath one of the following Miele ap- pliances: – Steam oven (DG 155) – Coffee machine (CVA 610) Read all the operating and installa- tion instructions for any other appli- ance installed in combination with the plate warmer. The cabinet dimensions required will depend on which appliance the plate warmer is installed with. When installed in combination with another appliance, the plate warmer must always be installed beneath
Summary of the content on the page No. 16
Installing the plate warmer The plate warmer must be installed above a fixed interim shelf within the cabinet to ensure that the cabinetry can support the weight of it and of any other appliance installed in combination with it. When installed in combination with another appliance, the plate warmer must always be installed beneath the other appliance. A shelf between the appliances is not necesary. ^ Trip the circuit breaker to the outlet. ^ Plug the plate warmer into the outlet. ^ Push the appl
Summary of the content on the page No. 17
Installing the plate warmer Adhering the insulation strips Aligning the front of the plate warmer ^ Remove the protective foil from the After installing the combination appli- adhesive strips. ance, it may be necessary under cer- tain circumstances to – align the front of the plate warmer. – align the gap between the plate warmer and the combination appli- ance. To help you do this, there are adjusting points underneath the nuts which se- cure the drawer to the telescopic run- ners. ^ Align the
Summary of the content on the page No. 18
18
Summary of the content on the page No. 19
19
Summary of the content on the page No. 20
Alteration rights reserved / 22 / 001 USA / CDN - 3401 M.-Nr. 05 478 600 (EGW 602 - 14) This paper consists of cellulose which has been bleached without the use of chlorine.
