Summary of the content on the page No. 1
Installation Instructions
ESW 47xx
ESW 48xx en_CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Summary of the content on the page No. 2
Electrical connection Power supply ,CAUTION: Before servicing, This appliance is equipped with a 5 ft disconnect the power supply by (1.5 m) long power cord with a either removing the fuse, shutting off three-prong grounding plug ready for the power main or manually connection to a 120 V, 15 A, 60 Hz "tripping" the circuit breaker. power supply. Installation work and repairs should Further installation details are on the only be performed by a qualified wiring diagram. technician in accordance w
Summary of the content on the page No. 3
Installation Installation tips Steam from the vents can damage – The warming drawer should be the cabinetry surrounding the placed at a convenient height for warming drawer. easy access. – The drawer should be installed clear Solo Installation: of drafts caused by open doors and A minimum gap of 2" (5 cm) must be windows. present between the upper edge of the warming drawer and the – Proper clearance must be allowed cabinetry. for the warming drawer to open with out interference. Installation in
Summary of the content on the page No. 4
Installation Dimensions for Solo Installation ESW 47x0 a Material must be moisture resistant Miele appliances can be installed ush or proud. Discuss your installation requirements with you architect, designer and installer. 27
Summary of the content on the page No. 5
(26) 15/16" 22 (582) 1" Installation ESW 48x0 a a Material must be moisture resistant 28 (610) 1/2" 24" 26"- 28 (660-724) 15/16" (659) 13/16" (757) 25 29 (51) (257) (248) 2" 1/8" 10 9 3/4" 11" (280)
Summary of the content on the page No. 6
Installation Dimensions for a combination installation with an oven ESW 47x0 a Material must be moisture resistant a 29 (257) 7/16" 11" 23 3/16" 11/16" 3/8" 1/8" 1/8" 13/16" 10 11/16" 1 1" (25) (280) (596) (5) (18) (10) (2,8) 22 (43) (580)
Summary of the content on the page No. 7
Installation ESW 48x0 a Material must be moisture resistant 30
Summary of the content on the page No. 8
Installation Installing the warming drawer ^ Push the casing in the cabinetry. ^ Remove the drawer from the casing before installing the appliance into the cabinetry. Removing the drawer ^ Secure the casing in the cabinetry with the six screws. Inserting the drawer ^ Pull out the telescopic skis from the ^ Pull the drawer completely out and casing. loosen the nuts. ^ Set the drawer on the telescopic skis ^ Carefully lift the drawer and pull it and secure with the two nuts. slowly out. Set the dr
Summary of the content on the page No. 9
Installation Integrated installations a Install a handle to the custom front panel using counter sunk screws. Models 4700 FB and 4800 FB b Remove the drawer from the casing. Custom made front panels can be See "Removing the drawer". installed with models 4700 FB and 4800 FB. The panel attached to the warming drawer front can be used as the drilling template for the custom panel. Panel dimensions 4700 FB 3 Width 27 / " (695 mm) 8 Height 11" (279 mm) 4800 FB 13 Width 29 / " (757mm) 16 Height 11"
Summary of the content on the page No. 10
Installation f Press the custom panel tightly onto h Hook the panels into the bottom on the removed panel. and secure at the top with two screws making sure the seal is seated correctly. g Screw the removed panel to the custom panel with the eight screws. 33
Summary of the content on the page No. 11
Alteration rights reserved / 3206 M.-Nr. 06 543 320 / 06 en-US
