Life Fitness Arctic Silver 95Se user manual

Summary of the content on the page No. 1

95Se Stairclimber
Assembly Instructions

Summary of the content on the page No. 2

Congratulations... and welcome to the world of The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of the Stairclimber as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Stairclimber.

Summary of the content on the page No. 3

IMPORTANT SAFETY INSTRUCTIONS! ⇒ DO NOT locate the Stairclimber outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Stairclimber if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services at the number in the Operation Manual. ⇒ DO NOT locate the Stairclimber any closer than 30 inches ( 76 cm ) to a television set. ⇒ DO NOT locate additional Stairclimbers any closer than a minimum of 42 inche

Summary of the content on the page No. 4

TOOLS REQUIRED FOR ASSEMBLY... Phillips Screwdriver, T27 Torx Wrench, Socket Set PARTS DESCRIPTION 1 Hex Head Bolt Qty: 2 2 Lock Nut Qty: 2 3/8 – 16 x 3 3/8 – 16 3 Hex Head Bolt Qty: 2 4 Torx Cap Screw Qty: 4 5/16 – 18 x 1.500 1/4 – 20 x .625 5 Phillips Pan Head Screw Qty: 8 6 Flat Head Screw Qty: 6 #8 – 18 x .625 1/4 – 20 x .625 7 Phillips Pan Head Screw Qty: 4 8 Phillips Cap Screw Qty: 2 #8 – 18 x .75 #6 – 32 x .375 9 Display Console Assembly Qty: 1 10 Monocolumn Qty: 1 11 Accessory Tray Qty:

Summary of the content on the page No. 5

A CX 1. Before proceeding, familiarize yourself with the parts of the Stairclimber and make sure that you have received all the items B described in the Parts List. 16 2. Locate the MONOCOLUMN (#10). Position the MONOCOLUMN SHROUD (#16) onto the MONOCOLUMN as shown. Position the MONOCOLUMN near the MONOCOLUMN MOUNTING BRACKET (A) as shown. Detach and feed the CONSOLE WIRE HARNESS (B) and COAXIAL CABLE (CX) through the MONOCOLUMN and out through the DISPLAY CONSOLE MOUNTING BRACKET (C) ACCESS HOL

Summary of the content on the page No. 6

5. Locate the USER LEFT BULLHORN (#13) with a Lifepulse sensor. Connect the 2-PIN CONNECTOR (2P) leading from the USER LEFT BULLHORN to the 2-PIN CONNECTOR (2PL) now leading from the HANDLEBAR 2P 14 BRACKET TUBE (E). Carefully feed any excess HEART RATE CABLE (2PL) 2PR into the HANDLEBAR BRACKET TUBE and secure the USER LEFT 15 BULLHORN to the HANDLEBAR BRACKET TUBE using three MOUNTING SCREWS (#6). Tighten the SCREWS securely. Repeat the procedure for the USER RIGHT BULLHORN (#14) with a Lifepu

Summary of the content on the page No. 7

8. Using four MOUNTING SCREWS (#5), attach the ACCESSORY TRAY (#11) to the DISPLAY CONSOLE (#9) as shown. 9 CAUTION: Do not over-tighten the SCREWS (#5). MISE EN GARDE : Ne serrez pas trop les VIS (Nº 5). 11 9. Attach all CABLES (H, CX) leading from the DISPLAY CONSOLE MOUNTING BRACKET (C) ACCESS HOLE to the back of the DISPLAY CONSOLE (#9). Connect the COAXIAL CABLE (CX) first. Followed by the 5- PIN, 4 PIN and 14 PIN CONNECTORS. CX 10. Feed any excess cable into the MONOCOLUMN (#10). Using fou

Summary of the content on the page No. 8

PRE-OPERATION CHECKLIST Ensure that all fasteners are tight. Make sure the Stairclimber is properly leveled and stable. (Refer to the Operation Manual) Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual) Read the entire Operation manual before using the Stairclimber. LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE Vérifiez si tous les dispositifs de fixation sont serrés Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable. (Référez-vous a