Summary of the content on the page No. 1
INSt ALLAtION
INStruCtIONS
OUTDOOR GAS FIREPLACE
®
ELITE SERIES
OutdOOr GAS FIrEPLACE
P/N 850,034M rEV. d 04/2009
this appliance is only for use with the type of gas
indicated on the rating plate. this appliance is
MODELS
not convertible for use with other gases, unless a
certified kit is used.
E36OdGNE E42OdGNE
E36OdGNE-H E42OdGNE-H
E36OdGPE E42OdGPE
INSt ALLEr: Leave this manual with the appliance.
E36OdGPE-H E42OdGPE-H
CONSuMEr: retain this manual for future reference.
INSt ALLAt
Summary of the content on the page No. 2
2 - one envelope containing the literature pack- Electronic appliances are designed to oper- t ABLE OF CONtENtS age which consists of the Homeowner's ate on natural gas or propane. An electronic manual, Installation Instructions and War- intermittent pilot ignition system provides safe, Packaging .........................................page 2 ranty. efficient operation. A battery pack is required Introduction ......................................page 2 to operate these units. 3 - three
Summary of the content on the page No. 3
Gas Pressure - All Models Orifice Sizes - Sea Level to High Altitude NEW yO r K ANd M ASSACHu SEtt S (All Models) rEQuIrEMENtS Tables 2 and 3 show the appliances' inlet and manifold gas pressure. These appliances are tested and approved for These appliances may be installed in the installation at elevations of 0-4500 feet (0-1372 following USA locations with the following meters) above sea level, using the standard requirements: Inlet Gas Supply Pressure burner orifice (See Table 4 ).
Summary of the content on the page No. 4
When locating the fireplace, consideration must ASSEMBLy OutLINE ASSEMBLy StEPS be given to combustibles and final finishing. Before you Start See Figure 18 and confine the final location Note: The following steps represent the normal of combustible finish materials to the "Safe sequence of installation. Each installation is Check your inventory list to be sure you have Zone". Also refer to Clearance Specifications unique, however, and might require a different all the necessary parts
Summary of the content on the page No. 5
When Planning for the installation of the fire- place, the framing height must be increased from 46-/2 inches to 47-/4 inches, when installing the drain pan. An additional space below the fireplace will also be required to threaded plumb a drain line. threaded reducer Elbow 3/4 3/4 x /2 @ 90° Step . Seal all joints, gaps and corners around (PVC) (PVC) the bottom of the drain pan before positioning the fireplace on its location (Figure 3 ). Step 2. On the exposed drain hole, instal
Summary of the content on the page No. 6
CLEArANCE SPECIFICA tIONS P G G FP FP H A D Q (See Note 2) B L B B FP F M FP FP I C X FP J or K A X = FIREPLACE OPENING = AIR SUPPLY INLET = AREA WHERE FIREPLACE IS NOT PERMITTED FP A = 2 in. . . . . . . . . . clearances above grade, I = 3 ft. (USA) . . . . clearance to service regulator veranda, porch, deck or 6 ft. (Canada) vent outlet and electric service. balcony. B = 12 in. . . . . . . . . . clearances to window or door J = 9 in. (USA) . . . . clearance to non-mechanical air that may be
Summary of the content on the page No. 7
Step 2. Level the firebox by checking the top FIrEPLACE INSt ALLAtION rOutING GAS LINE edge of the firebox. Shim if necessary. Step . Frame these appliances as illustrated in Route a 1/2" (13 mm) gas line along the inside Step 3. The fireplace should be secured to the Figures 7 through 9. All framing details must of the right side framing as shown in Figure side framing members, using the full length nail- allow for a minimum clearance to combustible 5. Gas lines must be routed, con
Summary of the content on the page No. 8
FIrEPLACE SPECIFICA tIONS dimensions - Inches (millimeters) Model No. A B C C 37 4- 3/4 23-/ 2 E36OdG (940) (0 6) (597) 43 47-3/4 29-/ 2 E42OdG (0 92) (2 3 ) (749) 20 (508) Weight And Volume Model Ship. Weight (lbs) Shipping Volume 35 Cu. Ft. E36OdG 200 lbs t op View E42OdG 38 Cu. Ft. 230 lbs t op Stand-Off Spacers (4 places) (25) 7-/6 Top of Firebox (79) 5 Opening (27) 4-5/6 28-/ 2 (049) Access Opening for (724) Gas Line 34-/ 4 umbilical Cord - Access - (870) r
Summary of the content on the page No. 9
FrAMING SPECIFICA tIONS Opening E360DG E420DG Back Wall Of Corner Installation Chase/Enclosure A 42-3/4" (1086) 48-3/4" (1238) Including Finishing B 46-1/2" (1181) 46-1/2" (1181) Materials If Any C 23-9/16" (599) 29-9/16" (751) d D 11-1/4" (286) 14-1/4" (362) F H E 63-1/2" (1613) 69-1/2" (1765) G F 31-3/4" (807) 34-3/4" (883) C G 20-1/2"( 521) 20-1/2"( 521) A H 44-3/16" (1122) 49-1/8" (1248) E rough Framing Face Table 1 (This Table Corresponds To Figures 7,8 & 9.) (unfinished Shown) Figure 8 Ba
Summary of the content on the page No. 10
VENT TH TH TP TP FIELd WIrING SPArK tO PILOt IGNItOr INtErMIttENt ELECtrONIC WIrING dIAGrAM Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. IGNItOr MOduL E 3V Refer to Figure 10 for the wiring schematic BLACK (IGNItOr) for these fireplaces. This fireplace is completely wired internally. BLACK (SENSOr ) On the right hand side of the fireplace, at the rear, are four
Summary of the content on the page No. 11
CONNECtING GAS LINE Gas Flex Line Connector Codes require a shut-off valve mounted in the 3/8" NPt x 3/8" /2" x 3/8" Flar e Gas supply line. Figure 12 illustrates two methods Flare Fitting Shut-Off Valve Valve for connecting the gas supply. The flex-line method is acceptable in the U.S., however, Canadian requirements vary depending on 3/8" Flex t ubing locality. Installation must be in compliance with local codes. Gas These appliances are equipped with a gas flex Stub line for use (wh
Summary of the content on the page No. 12
WAr NING: dO NOt OPErA tE tHE FIrE - PLACE FOr ANy ExtENdEd PErIOd rear Log OF tIME WItHOut tHE LAVA rOCK IN PLACE. tHE PAN CAN OVEr HEAt ANd MAy WArP ANd tHE FIrEPLACE MAy SHut OFF AutOMA tICALL y. INSt ALLING tHE LOGS After verifying that the fireplace operates properly, replace the cover and set the bottom refractory components in place. Use two (2) bags of lava rock to fill the bottom of the burner tray to completely cover the burner tube. Level the rock evenly. Place the rear log
Summary of the content on the page No. 13
Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning are similar to the flu CHECKING APPLIANCE OPErA tION with headaches, dizziness and/or nausea. If you have these signs, obtain fresh air immediately. With gas line installed run initial system check- t urn off the gas supply to the appliance and have it serviced by a qualified professional, as out before installing any additional accesso- it may not be operating correctly. ries. Follow the lighting instructions provided in
Summary of the content on the page No. 14
INSt ALLAtION ACCESSOrIES ANd COMPONENtS drain Pan The drain pan is used with the appliance. drain Pan Cat. No. Model description H465 dPSS36 drain Pan (36) H4652 dPSS42 drain Pan (42) NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4
Summary of the content on the page No. 15
GAS CONVEr SION KIt S WArNING: tHIS CONVErSION KIt SHALL BE AVErtISSEMENt: CEt ÉQuIPEMENt dE CONVErSION INSt ALLEd By A QuALIFIEd SErVICE AGENCy SEr A INSt ALLÉ PAr u NE AGENCE Qu ALIFIÉE d E IN ACCOrdANCE WItH tHE MANuFACturEr'S SEr VICE CONFOr MÉMENt Aux INStru Ct IONS du INStru Ct IONS ANd ALL APPLICABLE COdES ANd FABrICANt Et tOutES ExIGENCES Et COdES APPLI- rEQuIrEMENtS OF tHE AutHOrIzEd HAVING CABLES dE L'AutOrISÉS AVOIr LA jurIdICtION. SI jurISdICtION. IF tHE INFOrMA tION IN tHESE
Summary of the content on the page No. 16
VENt tH tH tP tP Electronic Appliances Pressure-t ap Pilot Stage Pilot Gas Step 4. dexen Electronic Valves - See Figure t erminal (Inlet) Outlet 20 and the instructions provided with the kit. Remove and discard the two pressure regulator mounting screws. Remove the pressure regula- Ground tor and diaphragm. Discard all removed compo- (tP) nents. Ensure the rubber gasket installed on the back of the replacement pressure regulator Supply HI LO Gas is properly positioned. Install the new
