Kustom KXB200H/HR user manual

Summary of the content on the page No. 1

OWNER’S MANUAL
KXB200H/HR BASS GUITAR AMPLIFIER
KXB200HR
KXB200
KXB200
KXB200H
Congratulations on the purchase of your new Kustom bass amplifier.
Your KXB Model draws on decades of amp design and manufacturing
experience at Kustom. This model was built from the ground up to offer
world-class tone, useful features and reliable performance. Inside this manual,
you’ll find valuable information about the amp’s controls and specifications.
Being familiar with its features will help you effectivel

Summary of the content on the page No. 2

FCC Statements 1. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate

Summary of the content on the page No. 3

ENGLISH kustom.com

Summary of the content on the page No. 4

FRENCH kustom.com

Summary of the content on the page No. 5

KXB200H/HR Control Panel KXB200 1 3 4 5 6 7 8 9 10 11 12 13 2 1. 0 dB Input: ¼-inch input that is intended for bass guitars with standard, passive electronics. 2. –6 dB Input: ¼-inch input that is optimized for bass guitars with active electronics. 3. Gain: Controls the input level to the preamp. Set so Clip indicator light is not lit, otherwise distortion may occur. 4. Volume: Controls the overall volume level of the amplifier. Use in conjunction with the Gain control to obtain the desired

Summary of the content on the page No. 6

KXB200H/HR Back Panel / KXB200H HR Speaker Outputs: These are two-conductor, ¼-inch external speaker jacks. These jacks are wired in a parallel configuration. Use them to connect the amplifier head to speaker cabinets with a minimum total impedance of 4 ohms. (Note: Be sure that the amp is turned off before connecting or disconnecting speaker cabinets.) Examples: If you have two 8-ohm speaker cabinets and plug one into each of the amplifier’s two speaker jacks, the total load will be 4 ohms

Summary of the content on the page No. 7

KXB200H/HR AC Mains kustom.com

Summary of the content on the page No. 8

KXB200H/HR Suggested Settings The following suggested settings will help you dial in a variety of popular tones. Keep in mind, these are starting points to get you up and running with your KXB amplifier. Feel free to experiment to achieve your own signature sounds. KXB200 TRADITIONAL/VERSATILE TONE In this setting, the amplifier will deliver a traditional, yet versatile, electric bass sound. Whether you are playing Rock, Country, Blues or Gospel, this setting will get you close. If you play w

Summary of the content on the page No. 9

® Kustom KXB200H/HR Specifications Output Power 200 Watts 4 Ohms at 5% THD+N Dual Input 0 dB: 500K Ohm, -6dB: 95K Ohm Input Impedance Gain 75 dB Gain and Master at Max, All EQ at 12 o’clock S/N Ratio -80 dB typical Below rated power Electronically Balanced DIrect Output Ground Lift Switch and Level control XLR Aux Input 800 mV Sensitivity Stereo 3.5mm High Impedance Headphone Output 15 mW @ 30 ohms Stereo 3.5mm, 8 ohm minimum per channel Effects Loop 800 mV/1K Ohm output Effects Send, Gain and

Summary of the content on the page No. 10

KXB200H/HR Signal Flow Diagram kustom.com

Summary of the content on the page No. 11

KXB200H/HR 19 November 2009 kustom.com

Summary of the content on the page No. 12

www.kustom.com Kustom Amplification, Inc. 3015 Kustom Drive Hebron, Kentucky USA 41048 888-4-KUSTOM (888-458-7866) All specifications are subject to change without prior notice. ©2010 Kustom