Summary of the content on the page No. 1
Product features and decoration may vary from the picture above.
JEEP and the Jeep grille design are registered trademarks of DaimlerChrysler Corporation and are used under license. ©DaimlerChrysler Corporation
Goodyear (and winged foot design) and Wrangler (for tires) are trademarks of The Goodyear Tire & Rubber Company, used with permission.
Fisher-Price, Power Wheels and Power Wheels by Fisher-Price are U.S. trademarks of Mattel, Inc.
Owner’s Manual with Assembly Instructions
Please read this
Summary of the content on the page No. 2
Table of Contents A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Warnings and Cautions B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cause over
Summary of the content on the page No. 4
Pb Parts C • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. 12 Volt Charger 12 Volt Battery Vehicle Bo
Summary of the content on the page No. 5
Parts Rear Bumper Knob Plate Seat Dash Cap Nut Assembly Tool Steering Wheel Steering Column Dash Knob – 2 Key Assembly Hood Sound Box Brush Guard Spacer Tube – 2 Hood Latch – 2 Steering Wheel Cover 5
Summary of the content on the page No. 6
Parts Windshield Frame - Front Windshield Frame - Back Windshield Hinge Pin – 2 Sport Bar Sport Bar Support - 2 Sport Bar Bracket Set Windshield Bracket – 2 Brush Guard Right Sidepipe Canopy Left Sidepipe Not Shown: Label Sheet - 2 6
Summary of the content on the page No. 7
Parts 1 1 #8 x 4" Screw – 2 1 /2" x /4" Machine Screw - 2 3 1 #8 x 1" Screw – 11 4 #10 x /2" Screw – 2 #10 x 1" Screw – 7 #8 x / " Screw – 6 1 1 2 #8 x 1 /4" Screw – 10 #6 x 1 / " Screw – 4 .354 Cap Nut - 2* All Shown Actual Size *For your convenience, an extra .354 cap nut is included. 7
Summary of the content on the page No. 8
Parts Diagram D D 43 38 33 37 28 43 33 32 36 21 32 35 33 15 46 10 31 15 23 29 30 31 3 24 10 20 19 17 27 13 16 18 22 13 10 12 11 14 45 13 8 6 4 9 10 13 4 5 10 25 26 1 44 40 41 39 34 7 44 40 13 42 2 3 Note: Some parts shown are assembled on both sides of the vehicle. 8
Summary of the content on the page No. 9
Parts Diagram No. Part Quantity No. Part Quantity 28 Windshield Frame, Front 1 1 Vehicle Body 1 29 Windshield Bracket 2 2 Steering Column 1 30 Sport Bar 1 3 .354 Cap Nut 2 31 Sport Bar Support 2 4 Hood Latch 2 32 Sport Bar Bracket 2 5 12 Volt Battery 1 1 33 #6 x 1 /2" Screw 4 6 Battery Clamp Unit 1 1 1 34 1 /2" x /4" Machine Screw 2 7 #8 x 4" Screw 2 ™ 35 KC Light Rack, Front 1 8 Taillight Lens 2 ™ 36 KC Light Rack, Rear 1 9 Taillight Housing 2 37 Light Cover 2 10 #8 x 1" Screw 11 38 Windshield
Summary of the content on the page No. 10
Battery Charging E ELECTRICAL HAZARD WARNING CAUTION • Battery can fall out and injure a Use the charger in dry locations only. child if vehicle tips over. Always use battery clamp. About Thermal Fuses • PREVENT FIRE ® Your Power Wheels 12 volt battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting - Never modify the electrical system. safety device which automatically “trips” and shuts down Alterations could cause a fire resulting operation of the vehicle if the
Summary of the content on the page No. 11
Battery Charging Assembly F WARNING Battery Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. Charger Connector IMPORTANT! Assemble the battery clamp unit to the dash of your vehicle before beginning assembly of your vehicle.The battery clamp unit must be assembled
Summary of the content on the page No. 12
Assembly Rear of Vehicle 4 2 Battery Left Sidepipe Clamp Unit Vehicle Body Screw Pegs • Insert two #10 x 1" screws through the holes in the • Turn the vehicle body upside down. battery clamp unit and into the pegs in the dash. • Fit the left sidepipe under the left (driver) side of the • Tighten the screws with a Phillips screwdriver. vehicle body. Do not over tighten. 3 • Insert two #8 x /4" screws through the top of the left sidepipe and into the screw pegs on the underside of the vehicle bod
Summary of the content on the page No. 13
Assembly Battery Dash Knob Plate Compartment 8 6 Door Pocket Battery Compartment Key Assembly Microphone Cord Sound Box T-End Dash View 1.5V x 3 • Bend the end of the microphone cord sothat it forms a “T”. “AA” (LR6) • Insert the end of the microphone cord through the square opening in the dash pocket. Pull gently on the cord to make sure it is secure in the dash. SHOWN ACTUAL SIZE • Hook the microphone onto the “U” slot on the dash pocket. • Loosen the screw in the sound box’s battery compartme
Summary of the content on the page No. 14
Assembly Holes Cap Nut 9 11 Steering Wheel Steering Column Cap Nut Assembly Tool Steering “UP” Column Bottom View • Turn the vehicle body upright. • Position the steering wheel upright (see inset). • Wipe the steering column with a paper towel to remove • Fit the steering wheel onto the steering column. any excess lubricant. • Fit a cap nut into the cupped end of the cap nut • Turn the vehicle body on its side. assembly tool. • Insert the straight end of the steering column up through • Hold th
Summary of the content on the page No. 15
Assembly Wide Tab 15 13 Headlight Lens Wide Notch Lens Guard • Fit the wide notch in the side of a headlight lens under Brush Guard Front Bumper the wide tab on a lens guard. • Press firmly on the inside of the headlight lens to snap it into the lens guard. • Repeat this procedure to assemble the other headlight lens to the remaining lens guard. • Fit and hold the brush guard against the front bumper. • Insert two #10 x 1" screws through the front of the brush guard and into the front bumper. Gr
Summary of the content on the page No. 16
Assembly Windshield Frame - Front Hood Latch 19 17 Hole Slots Tabs Tabs Hood Latch Hole • Insert a hood latch into one of the holes in the vehicle • Align the slots in the front half of the windshield frame body, near the hood area. with the tabs on the windshield brackets. 1 4 • Twist the base of the hood latch / turn to secure it in the • Fit the front half of the windshield frame onto the vehicle body. windshield brackets as shown. • Repeat this procedure on the other side of the hood area to
Summary of the content on the page No. 17
Assembly Short Seat T-Loop (pull through slot) Windshield Frame – Back Belt Strap 23 21 Fastener End End T-Loops Slots Slots Windshield Frame – Front Seat Slot • Turn the seat upside down. • Insert the fastener end of a short seat belt strap through the slot near the outer edge of the seat. Make sure the • Fit the back windshield frame onto the front windshield side of the seat belt with the fastener faces the outer frame. Make sure the slots at the bottom of the two edge of the seat. windshiel
Summary of the content on the page No. 18
Assembly Seat Canopy Sleeves 25 27 Canopy Seat Back Tab Sleeves 2 PUSH HERE 1 Canopy Tabs 1 Slot Tabs Sport Bar • With the seat at an angle, insert the tabs on the front edge of the seat into the slots in the foot-well wall . • Position the sport bar on its side so that the sport bar ends curve away from you. • Push down firmly on the edge of the seat above each tab to insert and “snap” the tabs into the slots . • Position the canopy opposite the sport bar with the netting facing away from you.
Summary of the content on the page No. 19
Assembly TM KC Light Sport Bar Bracket Rack - Back Half 29 31 Ring Tabs Side Leg Tunnel Sport Bar Sport Bar TM Support KC Light Rack - Front Half • Position the sport bar with the ends on a flat surface, • Using safety scissors, remove the sport bar brackets from as shown. the plastic connector. Dispose of the plastic connector. TM • Position the sport bar upright. • Fit and hold the front and back halves of the KC light TM rack against the sport bar. Make sure the two KC light • Fit a sport ba
Summary of the content on the page No. 20
Assembly Sport Bar 33 35 Side Legs Rear Bumper PUSH HERE Side Fender Tabs Rear Bumper Support PULL UP HERE Lower Rail • Face the rear of the vehicle. • Fit the lower rail on the rear bumper over the rear bumper supports. • Fit the sport bar and sport bar support legs into the holes • Gently bend the tabs at the bottom of the rear bumper in the vehicle body. under the vehicle. • Push down firmly on a sport bar side leg while pulling up on the side fender to fit the sport bar into the vehicle b
