Summary of the content on the page No. 1
Installation
Manual
The Evolution series by InSinkErator® is a new standard in sound and grind
performance. Featuring exclusive patented SoundSeal™ and MultiGrind™
technologies, no food waste disposer grinds more with less noise.
www.insinkerator.com
1
Summary of the content on the page No. 2
Parts Included: Lower Mounting Ring Stopper 1 A or Stopper Anti-Vibration Mount™ 2 A (Cover Control Stopper differs from standard disposer stopper.) Dishwasher Inlet Quiet Collar™ Sink Baffle B Anti-Vibration Tailpipe Mount™ Sink Flange C J Fiber Gasket D Disposer Backup Flange E ® Discharge Tube Jam-Buster Wrench N K Mounting Ring F 1 1/2" Screws Extension Tube Hose Clamp G P (Included only with L the Cover Control Model) 1 1/8" Screws H Discharge Tube ™ Bio-Charge Bottle Snap Ring M O I (Inclu
Summary of the content on the page No. 3
A B E Dimensions: Model A B C D E 611/16" 4" 131/2" 9" 53/4" Excel 611/16" 4" 125/8" 83/4" 53/4" Premier 611/16" 4" 125/8" 83/4" 53/4" Essential Compact 6" 4" 121/8" 8" 53/4" 6" 4" 121/8" 8" 53/4" Space Saver 611/16" 4" 131/2" 10" 53/4" Cover Control 611/16" 4" 125/8" 83/4" 53/4" SepticAssist 3 D C
Summary of the content on the page No. 4
Removal of old disposer: WARNING ! If you are replacing 3 1 2 Falling Hazard an existing disposer, continue to Step 2. If there is no existing K disposer, disconnect sink drain and skip to Step 10. W A R N I N G SHOCK HAZARD Support disposer, insert end of Disconnect drain trap from waste Turn off electric power at ® Jam-Buster wrench (K) into discharge tube. Disconnect fuse box or circuit breaker. right side of mounting lug, and dishwasher if connected to the turn. Disposer will fall free. disp
Summary of the content on the page No. 5
Installation of new disposer: C A U T I O N CLEAN DRAIN LINE BEFORE INSTALLING DISPOSER Failure to clean sink drain line may result in drain line blockage. With drain auger, clear all hardened waste material in horizontal drain line. 10 11 12 C C C D E G Evenly apply 1/2” thick rope of F plumber’s putty around flange Press flange (C) firmly into sink (C). drain. Remove excess putty. Insert fiber gasket (D), backup flange (E) and mounting ring (F). Hold in place while inserting snap ring (I). 13
Summary of the content on the page No. 6
1 2 Installation of new disposer (continued): * 16 ! 17 18 *CAUTION: DISHWASHER CONNECTION ONLY Knock out *WARNING: SHOCK HAZARD. drain plug and remove plug from Turn disposer over and remove inside of disposer. *WARNING: SHOCK HAZARD. electrical cover plate. Pull With electrical supply turned out wires. DO NOT REMOVE off, insert cable connector (not CARDBOARD SHIELD. included) and run electrical cable through access hole on bottom of disposer. Tighten cable connector. 19 20 L 21 M N *WARNING: S
Summary of the content on the page No. 7
2 Installation of new disposer (continued): 22 23 23a Hang disposer by aligning 3 mounting tabs with slide-up Turn mounting ring until all ramps on mounting ring. 3 mounting tabs lock over (COVER CONTROL MODEL ONLY) the ridges on the slide-up Turn mounting ring until all 3 ramps. mounting tabs lock over the ridges on the slide-up ramps. Attach magnetic cover con- trol switch to the screws. Make sure plastic guides go UNDER mounting ring. 24 25 26 Model Evolution 18005585700 Model Evolution N 050
Summary of the content on the page No. 8
™ INSTALLING AND REPLACING THE BIO-CHARGE BOTTLE (For SepticAssist Model Only.) INSTALLING THE BIO-CHARGE BOTTLE: Use only REPLACING THE BIO-CHARGE BOTTLE: To keep your ™ ™ InSinkErator Bio-Charge . See “Changing Bio-Charge septic system operating at peak efficiency, replace the ™ Bottle” for safety instructions and information on Bio-Charge bottle when it is empty. ™ obtaining Bio-Charge replacements. Do no squeeze the Bio-Charge is available wherever InSinkErator Septic Bio-Charge bottle; squ
Summary of the content on the page No. 9
TIPS FOR TROUBLE-FREE OPERATION • Run disposer along with a moderate to strong flow of cold water, continue run cold water for 15 seconds after grinding is complete. • Avoid using hot water when grinding food waste. It is OK to drain hot water into the disposer between grinding periods. • Avoid pouring grease or fat into your disposer or drain. Standard Disposers (Badger® Series) (Evolution Series) (Evolution Excel) Everyday food waste scraps Vegetable Peels Avoid grinding large amounts at one
Summary of the content on the page No. 10
USER MAINTENANCE INSTRUCTIONS RELEASING DISPOSER JAM CLEANING DISPOSER This disposer is equipped with a Jam-Sensor Circuit™ that Over time, food particles may accumulate in the grind will prevent jams while grinding virtually any food mate- chamber and baffle. An odor from the disposer is usually rial. In the unlikely event that the disposer is jammed, a sign of grease and food buildup, caused by insufficient release it by following these steps. water flow during and after disposer use. To clean
Summary of the content on the page No. 11
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS (SAVE THESE INSTRUCTIONS) W A R N I N G When using electric appliances, Personal Injury: Do not position your head or basic precautions are always to body under disposer; unit could fall during be followed, including: removal or installation. • Read all instructions before using the appliance. • To reduce the risk of injury, close supervision is W A R N I N G required when an appliance is used near children. Do not ope
