Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY
Safety Notice
Magnetic Recumbent Bike
Hardware Pack
PL-43231
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PL-43231
Retain This
Manual for
Reference
07-01-05
OWNER'S
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.c
Summary of the content on the page No. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. 1 IMPORTANT SAFETY NOTICES..................................................................…. 2 HARDWARE PACK……….....…....................................................................…. 4 ASSEMBLY INSTRUCTIONS........................................................................…. 5 EXPLODED DIAGRAM……………………………………………………………. 10 PARTS LIST.................
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time shoul
Summary of the content on the page No. 4
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Rear Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3
Summary of the content on the page No. 5
HARDWARE PACK Part# Description Identifier #15 M10 x 3” Carriage Bolt (Qty 2) #16 Ø 1” Bent Washer (Qty 2) #17 M10 Acorn Nut (Qty 2) #19 Ø 7/8” Bent Washer (Qty 3) #18 M8 x 5/8” Allen Bolt (Qty 24) #20 Ø 5/8” Washer (Qty 21) #21 M8 x 2 ¾”
Summary of the content on the page No. 6
ASSEMBLY INSTRUCTION NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram1) A.) Attach the Front Stabilizer (#2) to the Main Frame (#1). Secure it with two M10 x 3” Carriage Bolts (#15), ∅1” Bent Washers (#16), and M10 Acorn Nuts (#17). B.) Attach the Base Frame (#7) to the Main Frame (#1). Secure it with six M8 x 5/8” Allen Bolts (#18) and Ø 5/8” Washers (#20). C.) Slide the Seat Post (#8) onto the Base Frame
Summary of the content on the page No. 7
STEP 2 (See Diagram 2) A.) Note: In able to hold the Handlebar Post (#4) while connecting the cables and wires, extra help may be needed. Attach the Handlebar Post (#4) to the Main Frame (#1). Connect the Middle Computer Sensor Wire (#24) from the bottom of Handlebar Post to the Lower Computer Sensor Wire (#25) from the main body of the bike. B.) Slide the cable wire from the Upper Tension Connector (#23) in between the opening on the wire holder on the Lower Tension Connector (#26). Pul
Summary of the content on the page No. 8
STEP 3 (See Diagram 3) A.) Attach the Seat Support (#9) to the Seat Post (#8). Secure it with two M8 x 2 ¾” Hex Bolts (#21), four Ø 5/8” Washers (#20), and two M8 Aircraft Nuts (#22). B.) Attach the Seat Handle (#10) to the Seat Support. Secure it with two M8 x 2 ¾” Hex Bolts (#21), four Ø 5/8” Washers (#20), and two M8 Aircraft Nuts (#22). DIAGRAM 3 7
Summary of the content on the page No. 9
STEP 4 (See Diagram 4) A.) Attach the Seat (#13) onto the Seat Support (#9). Secure it with four M8 x 5/8” Allen Bolts (#18). B.) Attach the Backrest Board (#14) to the Seat Support. Secure it with four M8 x 5/8” Allen Bolts (#18). DIAGRAM 4 8
Summary of the content on the page No. 10
STEP 5 (See Diagram 5) A.) Thread the Left Pedal (#11) Counterclockwise into the Left Crank. Thread the Right Pedal (#12) Clockwise into the Crank on the other side. DIAGRAM 5 9
Summary of the content on the page No. 11
10
Summary of the content on the page No. 12
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Handlebar Post 1 5 Handle Bar 1 6 Computer 1 7 Base Frame 1 8 Seat Post 1 9 Seat Support 1 10 Seat Handle 1 11 Left Pedal 1 12 Right Pedal 1 13 Seat 1 14 Backrest Board 1 15 M10 x 3” Carriage Bolt 2 16 Ø 1” Bent Washer 2 17 M10 Acorn Nut 2 18 M8 x 5/8” Allen Bolt 24 19 Ø 7/8” Bent Washer 3 20 Ø 5/8” Washer 21 21 M8 x 2 ¾” Hex Bolt 4 22
Summary of the content on the page No. 13
COMPUTER AUTO START / STOP When exercise starts, the monitor will automatically turn on and display the progress. When exercise stops, the monitor will automatically turn off (after 4 minutes) to save energy. Press “MODE” key to scan Time, Speed, Distance, and Calories. DISPLAY: Time Display the elapsed time. Max value is up to 99:59 Speed Display the current speed in miles per hour. Distance Display the distance traveled in Miles. Max value
Summary of the content on the page No. 14
Maintenance and Storage 1. Inspect and tighten all parts each time you use the machine. Replace any worn parts immediately. 2. The bike can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. 3. Store the machine IN-DOOR. Excess moisture and water would cause rust on the frame. 4. The machine shall be placed at least 24 inches away from the wall or/and any other object such as furniture to provide safe access to and passage around the ma
Summary of the content on the page No. 15
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cus
