Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
MARCY BODY CYCLE
Safety Notice
PL-105
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PL 105
Retain This
Manual for
Reference
07-02-01
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
OWNER'S
Tel: (800) 999-8899 Fax: (626) 961-9966
MANUAL
www.impex-fitness.com
info@impex-fitness.com
Summary of the content on the page No. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................….1 IMPORTANT SAFETY NOTICES..................................................................….2 HARDWARE IDENTIFIER.....…....................................................................….3 ASSEMBLY INSTRUCTIONS........................................................................….4 EXPLODED DIAGRAM……………………………………………………………….8 PARTS LIST......................
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person a
Summary of the content on the page No. 4
3
Summary of the content on the page No. 5
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram1) A.) Attach the Front Stabilizer (#13) to the Main Frame (#1). Secure it with two M8 x 2 ½” Carriage Bolts (#15), ∅5/8” Bent Washers (#14), and M8 Acorn Nuts (#16). B.) Insert Rear Stabilizer (#10) into the rear bottom of Main Frame (#1). Secure it with t
Summary of the content on the page No. 6
STEP 2 (See Diagram 2) A.) Insert the Axle (# 4) into the Pivot on the Main Frame (#1). Attach the Left and Right Handlebars (#2) & (#32) onto the Axle from both sides. Secure the Axle with two ∅ 7/8” Washers (#7) and M8 Nylon Nuts (#8). Close both ends with two Axle End Caps (#9). B.) Insert the Lower Handlebar (#3) into the Left Handlebar (#2). Secure it with two M6 x 5/8” Allen Bolts (#6) and ∅½” Flat Washers (#5). Repeat same procedure to install the other side. DIAGRAM 2
Summary of the content on the page No. 7
STEP 3 (See Diagram 3) A.) Attach the Connecting Rod (#26) on the Lower Handlebar to the Crank. Align the hole. Insert a Bushing (#29) into the hole on the Rod. Attach a Spacer (#30) to the Bushing. Then insert the Left Pedal (#27) through the Rod into the Crank. Secure the Pedal with a ∅1/2” Nylon Nut (#28). B.) Repeat the above procedure (A) to install the other side. DIAGRAM 3 6
Summary of the content on the page No. 8
STEP 4 (See Diagram 4) A.) Attach the Seat (#18) to the Seat Post (#19). Secure it with three ∅ 5/8” Washers (#21), Spring Washers (#22), and M8 Nylon Nuts (#23). B.) Slide the Seat Post Sleeve (#20) onto the Seat Post (#19). Insert the Seat Post into the opening on the Main Frame (#1). Select the Seat height and secure it with a Lock Knob (#17). C.) Attach the Computer (#24) onto the computer holder on the Main Frame. Plug the Computer Sensor Wire (#25) into the Computer.
Summary of the content on the page No. 9
EXPLODED DIAGRAM 8
Summary of the content on the page No. 10
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Main Frame 1 2 Left Handlebar 1 3 Lower Handlebar 2 4 Axle 1 5 ∅ ½” Flat Washer 4 6 M6 x 5/8” Allen Bolt 4 7 ∅ 7/8” Washer 2 8 M8 Nylon Nut 2 9 Axle End Cap 2 10 Rear Stabilizer 1 11 ∅ 5/8” Washer 3 12 M8 x 5/8” Allen Bolt 3 13 Front Stabilizer 1 14 ∅ 5/8” Bent Washer 2 15 M8 x 2 ½” Carriage Bolt 2 16 M8 Acorn Nut 2 17 Lock Knob 1 18 Seat 1 19 Seat Post 1 20 Seat Post Sleeve 1 21 ∅ 5/8” Washer 3 22 ∅ ½” Washer 3 23
Summary of the content on the page No. 11
COMPUTER Press “MODE” on Computer to select each function. Functions: • Scan: Automatically scan through each mode in sequence every 6 seconds. • Speed: Shows the current speed up to 99.9 ML/H. • Distance: Accumulates pedaled distance up to 99.99 ML from zero. • Time: Accumulates total time up to 99:59. • Calories: Accumulates calories consumption during exercise; max value is 9999 cal. 1. The computer will automatically shut off after 4 minutes when not in use. 2. To
Summary of the content on the page No. 12
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu
