Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE BENCH
Hardware Identifier
PHC -764
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PHC 764
Retain This
Manual for
Reference
07-17-03
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-f
Summary of the content on the page No. 2
_____________________________________________________ TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE.....................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 4 EX
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
Summary of the content on the page No. 4
HARDWARE PACK 3
Summary of the content on the page No. 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beams (#1) & (#2) by the Cross Brace (#3) in the mid-span. Align the holes then secure each end of Cross Brace with one Bent Bracket (#9), two M10 x 3 ¾” Carriage Bolts (#47), ∅ ¾” Washers (#48), and M10 Aircraft N
Summary of the content on the page No. 6
STEP 2 (See Diagram 2) A.) Attach the Leg Developer Holder (#5) to the Front Base (#6). Secure it with three M10 x 5/8” Allen Bolts (#52) and ∅ ¾” Washers (#48). B.) Attach the Leg Developer Holder (#5) to the front of the Main Seat Support (#4). Secure it with one M10 x 2 ½” Carriage Bolt (#60) from the top, two M10 x 2 ¾” Carriage Bolts (#51) from the side, three ∅ ¾” Washers (#48) and three M10 Aircraft Nuts (#49). C.) Attach the Rear of the Main Seat Support (#4) to the Cross Br
Summary of the content on the page No. 7
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#19) to the Leg Developer Holder (#5). Secure it with an Axle (#35), two ∅ ¾” Washers (#48), and two M10 x 5/8” Allen Bolts (#52). B.) Insert one M8 x 2 1/8” Allen Bolt (#62) through the hole on the Lat Bar Frame (#15) and secure it with a M8 Aircraft Nut (#63). C.) Slide the Weight Holder (#16) onto the Lat Bar Frame. Insert the Lat Bat Frame into the top opening on the Leg Developer Holder. Use the Lock Knob (#31) to secure the
Summary of the content on the page No. 8
STEP 4 (See Diagram 4) A.) Attach the hole-side of the Seat Bracket (#11) to the pivot on the Main Seat Support (#4). Push two ∅ 5/8” Bushings (#43) into the holes on the Pivot. B.) Attach the Backrest Supports (#13) to the Pivot. Secure it with one M10 x 7 ¼” Hex Bolt (#50), two ∅ ¾” Washers (#48), and one M10 Aircraft Nut (#49). Do not tighten the Nut and Bolt yet. Place the Backrest Incline Support (#14) in between the two Backrest Supports. Securely tighten the Bolt (#50) and Nut (#
Summary of the content on the page No. 9
STEP 5 (See Diagram 5) A.) Insert one Foam Roll Tube (#20) halfway through the hole on the Leg Developer Holder (#5). Insert two Foam Roll Tubes (#20) halfway through the holes on the Leg Developer (#19). Push six Foam Rolls (#21) onto the Tubes from both ends. Plug six Foam Roll End Caps (#22) into the ends. B.) Attach the two Olympic Sleeves (#32) to the weight post on Leg Developer (#19) and Weight Holder (#16). Attach one Spring Clip (#33) to each Olympic Sleeve. DIAGRAM 5 8
Summary of the content on the page No. 10
STEP 6 (See Diagram 6) A.) Attach the ball end of the Cable (#18) to a Pulley (#26). Place the Pulley in the open slot on top of the Lat Bar Frame (#15). Secure the Pulley with one M10 x 2 3/8” Allen Bolt (#55), two Pulley Bushings (#29), and one M10 Aircraft Nut (#49). B.) Draw the Cable over the Pulley to the open bracket on the Lat Bar Frame. Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#56), one L-shaped Pulley Cover (#27), two ∅ ¾” Washers (#48), and one
Summary of the content on the page No. 11
10
Summary of the content on the page No. 12
PARTS LIST KEY NO. DESCRIPTION Q’ty 51 M10 x 2 ¾” Carriage Bolt 4 1 Left Upright Beam 1 52 M10 x 5/8” Allen Bolt 5 2 Right Upright Beam 1 53 M10 x 1” Allen Bolt 1 3 Cross Brace 1 54 1 ¾” Square End Cap 1 4 Main Seat Support 1 55 M10 x 2 3/8” Allen Bolt 1 5 Leg Developer Holder 1 56 M10 x 2” Allen Bolt 1 6 Front Base 1 57 C-clip 2 7 Backrest Adjustment Bar 1 58 M6 x 1 3/8” Hex Bolt 4 8 Crutch 2 59 ∅ ½” Washer 8 9 Bent Bracket 2 60 M10 x 2 ½” Carriage Bolt 1 10 Bracket
Summary of the content on the page No. 13
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu
