Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
®
Table of Contents
MARCY HOME GYM
Safety Notice
MWM-1509
Hardware Identifier
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1509
Retain This
Manual for
Reference
07-24-07
OWNER'S
®
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
inf
Summary of the content on the page No. 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 EXPLODED DIAGRAM……………………………………………………………………… 18
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual and all posted warning labels before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machin
Summary of the content on the page No. 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
Summary of the content on the page No. 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
Summary of the content on the page No. 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
Summary of the content on the page No. 7
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
Summary of the content on the page No. 8
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect two Lower Guide Rods (#46) and two Upper Guide Rods (#45) with two M10 Stud Bolts (#48). Firmly thread the Rods together. B.) Insert the two Lower Guide Rods (#46) into the holes on the Rear Base Frame
Summary of the content on the page No. 9
DIAGRAM 1 8
Summary of the content on the page No. 10
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#66) onto the Guide Rods. Make sure the grooves on the Weight Plates are all facing the back of the machine and downward. Insert the Selector Rod (#47) through the center hole on the Weight Plates. B.) Slide the Selector Stem (#65) onto the Guide Rods. C.) Slide the Ring on the Selector Pin (#67) onto the Selector Rod. Insert the Selector Pin into the selected groove to choose the number of weight plates for exercise. Note: Each wei
Summary of the content on the page No. 11
DIAGRAM 2 10
Summary of the content on the page No. 12
STEP 3 (See Diagram 3) A.) Attach the Left Butterfly (#10) to the open bracket on the Front Press Base (#9). Secure it with one M12 x 4” Hex Bolt (#84), two Ø 1” Washers (#88), and one M12 Aircraft Nut (#91). B.) Slide a Butterfly Foam Roll (#57) onto the Left Butterfly arm. C.) Repeat Steps A&B above to install the Right Butterfly (#11). D.) Attach two 1 ¾” Spacers (#61) to the Lower & Upper Vertical Frames (#4 & #15). Attach the Backrest Board (#38) to the Spacers. Secure it with two
Summary of the content on the page No. 13
CABLE LOOP DIAGRAM 12
Summary of the content on the page No. 14
STEP 4 (See Diagram 4 & Cable Loop Diagram) A.) Attach the 122” Upper Cable (#40) to the open bracket underneath the front of Upper Frame (#8). B.) Attach a Pulley (#49) to the open bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#75), two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#90). Note: The Ball Stopper on the Cable should be underneath the Frame and Pulley. C.) Draw the Cable towards the back of the machine to the open bracket under the Upper Frame. Repeat Procedu
Summary of the content on the page No. 15
DIAGRAM 4 14
Summary of the content on the page No. 16
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach one end of the 119” Butterfly Cable (#41) to the hook on the Right Butterfly (#11). B.) Draw the Cable to the right open bracket on the back of Upper Vertical Frame (#15). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#75), two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#90). D.) Draw the Cable over the Pulley then downward. Attach the Cable to a Crossed Double Floating Pulley Bracket (#14). Instal
Summary of the content on the page No. 17
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 130” Lower Cable (#39) to the opening on the bottom of the Leg Developer (#7). B.) Attach a Pulley (#49) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#77), two Pulley Bushings (#33), and one M10 Aircraft Nut (#90). C.) Draw the Cable underneath the Pulley through the opening on the Lower Vertical Frame (#4) to the open bracket on the back. D.) Attach a Pulley to the open bracket. Secure it with one M10 x 1 ¾
Summary of the content on the page No. 18
DIAGRAM 6 17
Summary of the content on the page No. 19
EXPLDOED DIAGRAM 18
Summary of the content on the page No. 20
PARTS LIST KEY NO. DESCRIPTION Q’ty 51 Handle Grip 6 1 Main Base Frame 1 52 Ø 1” Con-shaped End Cap 3 2 Rear Base Frame 1 53 Foam Roll End Cap 4 3 Front Base Frame 1 54 Ø 2” End Cap 4 4 Lower Vertical Frame 1 55 Ø 1 ¾” End Cap 2 5 Seat Support 1 56 Foam Roll 4 6 5 ½” Curved Bracket 3 57 Butterfly Foam Roll 2 7 Leg Developer 1 58 Ø 1” x Ø 5/8” Bushing 2 8 Upper Frame 1 59 Ø 1” x Ø ½” Bushing 4 9 Front Press Base 1 60 Ø ¾” x Ø ½”
