Homelite F3055 user manual

User manual for the device Homelite F3055

Device: Homelite F3055
Category: Brush Cutter
Manufacturer: Homelite
Size: 0.56 MB
Added : 6/5/2014
Number of pages: 22
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Homelite F3055. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Homelite F3055.

For your convenience

If looking through the Homelite F3055 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Homelite F3055 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Homelite F3055 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Homelite F3055 User manual - Online PDF
Advertisement
« Page 1 of 22 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Homelite F3055 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Homelite F3055. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

OPERATOR’S MANUAL
Trimmer / Brushcutter
F3055
UT70129
Your new trimmer has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual.
Thank you for buying a Homelite trimmer.
SAVE THIS MANUAL FOR FUTURE REFERENCE

Summary of the content on the page No. 2

TABLE OF CONTENTS ■■■■■ Safety..................................................................................................................................................................... 2 - 3 ■■■■■ Symbols ................................................................................................................................................................. 4 - 5 ■■■■■ Technical Data ...............................................................................................

Summary of the content on the page No. 3

SAFETY SPECIFIC SAFETY RULES FOR BRUSHCUTTER AND ■■■■■ Inspect the unit before each use for loose fasteners, fuel BLADE USE leaks etc. Replace any damaged parts before use. ■■■■■ After engine stops, keep rotating blade in heavy grass ■■■■■ The string head or blade will rotate during carburettor or pulpy weeds until it stops. adjustments. ■■■■■ Do not operate the brushcutter unless the blade guard is ■■■■■ It has been reported that vibrations from hand-held tools firmly secured in place and in g

Summary of the content on the page No. 4

SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely. SYMBOL NAME EXPLANATION Safety Alert Symbol Indicates danger, warning or caution. It means attention!!! Your safety is involved. Read Your Operator’s Manual Your manual contains special messages to bring attention to potential safety concerns as well as operating and servicing inform

Summary of the content on the page No. 5

SYMBOLS SYMBOL NAME EXPLANATION Switch On/Off Switch I = ON to Run O = OFF to Stop Handle Decal Positioning decal for front handle. The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER:

Summary of the content on the page No. 6

UNPACKING INSTRUCTIONS PACKING LIST FOR OWNER’S KIT ■■■■■ Carefully remove the product from the carton. ■■■ Grass deflector ■■ ■■■■■ Inspect the product to make sure no breakage or ■■■ Blade guard ■■ damage occurred during carriage. ■■■ Tri-Arc blade ■■ ■■■■■ Do not discard the packing material until you have ■■■ Shoulder strap ■■ inspected and operated the product. ■■■ Silencer guard, torque wrench and screws ■■ ■■■ Holding pin ■■ ■■■ Spanners - 13 mm (1/2 in) and 16 mm (5/8 in) ■■ ■■■ Fixings

Summary of the content on the page No. 7

ASSEMBLY HANDLE See Figure 2. 1. Place the handlebar in the bottom clamp located on the shaft housing. NOTE: The throttle trigger must be mounted to the BOTTOM operator’s right side. CLAMP THROTTLE 2. Insert the square tab of top clamp into the mounting hole TRIGGER of the bottom clamp. 3. Adjust the handlebar for best operator control in a comfortable upright position. TOP CLAMP 4. Install the knob and tighten securely. HANDLEBAR BOTTOM THROTTLE CLAMP TRIGGER TOP CLAMP KNOB BOTTOM CLAMP THROTTL

Summary of the content on the page No. 8

ASSEMBLY ATTACHING THE SHOULDER STRAP REAR HOUSING See Figure 3. 1. Connect the latch on the shoulder strap to the TORQUE strap hanger. WRENCH 2. Adjust the strap to a comfortable position. NOTE: To quickly release the product from the shoulder strap, sharply pull the quick release tab. SCREWS SILENCER GUARD SHOULDER STRAP QUICK RELEASE TAB BENT END OF SILENCER GUARD LATCH OPENING IN REAR HOUSING Fig. 4 STRAP HANGER GRASS DEFLECTOR AND BLADE GUARD Fig. 3 USE NOTE: When converting from brushcutt

Summary of the content on the page No. 9

ASSEMBLY BLADE GUARD FOUR SCREWS See Figure 6. 1. Attach the blade guard to the mounting bracket; install MOUNTING CLAMP the four screws (10-24 x 3/4 in) from the top of the mounting bracket through the blade guard and into the threaded mounting plates. 2. Using the torque wrench supplied, tighten all four screws BLADE GUARD securely. NOTE: When using the string head, the string shield must be attached to blade guard. NOTCHES GRASS DEFLECTOR See Figure 6. 1. Attach the grass deflector to the b

Summary of the content on the page No. 10

ASSEMBLY INSTALLING THE BLADE See Figure 8. 1. Place the upper flange washer over the gear shaft with GEAR HEAD the hollow side toward the blade guard. 2. Centre the blade on the upper flange, making sure the blade sits flat. Install the cupped washer with the raised centre away from the blade. Install the blade nut. The blade turns anticlockwise from the operator’s position. BLADE 3. Place the holding pin through the slot in the upper flange UPPER FLANGE GUARD washer and the hole in the gear

Summary of the content on the page No. 11

OPERATION 4. Prior to replacing the fuel cap, clean and inspect FUEL AND REFUELLING the gasket. HANDLING THE FUEL SAFELY 5. Immediately replace fuel cap and hand tighten. Wipe up ■■■■■ Always handle fuel with care. It is highly flammable. any fuel spillage. Move 9 m (30 ft) away from refuelling ■■■■■ Always refuel outdoors where there are no sparks and site before starting engine. flames. Do not inhale fuel vapour. NOTE: It is normal for smoke to be emitted from a new ■■■■■ Do not let petrol

Summary of the content on the page No. 12

OPERATION CUTTING TIPS See Figure 10. ■ Keep the trimmer tilted toward the area being cut; this is the best cutting area. ■ Do not cut in dangerous cutting area. ■ Use the tip of string to do the cutting; do not force string head into uncut grass. ■ Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, kerbs and wood may wear string rapidly. ■ Avoid trees and shrubs. Tree bark, wood mouldings, cladding and fence posts can easily be damaged by the string. DANGEROUS

Summary of the content on the page No. 13

OPERATION OPERATING THE BRUSHCUTTER Hold the brushcutter with the right hand on the trigger APPROACH THE WEEDS handle and the left hand on the left handle. Keep a firm grip BEING CUT FROM THE RIGHT. with both hands while in operation. Brushcutter should be THE WEEDS WILL BE CUT held at a comfortable position with the trigger handle about AGAINST THE LEFT SIDE OF hip height. Maintain your grip and balance on both feet. THE BLADE GUARD. Position yourself so that you will not be drawn off balance b

Summary of the content on the page No. 14

OPERATION STARTING AND STOPPING See Figures 14 and 15. NOTE: The unit is equipped with an automatic choke feature. The starting instructions for this feature are different from units with a manual choke. Be sure to read and follow the starting instructions below. INTERLOCK IGNITION SWITCH I = ON TO RUN WARNING: O = OFF TO STOP Never start or run the engine inside a closed or poorly ventilated area; breathing exhaust fumes can kill. THROTTLE TRIGGER TO START A COLD ENGINE: 1. Lay trimmer on a fl

Summary of the content on the page No. 15

MAINTENANCE 6. Make sure the string head and the spool retainer are WARNING: installed on the shaft by turning the retainer anticlockwise to tighten. Use only original manufacturer’s replacement parts, 7. Pull the strings again to rotate the spool into cutting accessories and attachments. Failure to do so can position. Push the spool retainer down while pulling on cause possible injury, poor performance and may string(s) to manually advance the string and to check for void your warranty. prope

Summary of the content on the page No. 16

MAINTENANCE STRING REPLACEMENT See Figures 18, 19, 20 and 21. 1. Stop the engine and disconnect the sparking plug wire. Hold the string head and unscrew the spool retainer. Turn clockwise. 2. Remove the spool from the string head. NOTE: Keep the spring attached to the spool. Remove any old string SECOND remaining on the spool. STRING 3. Cut two pieces of string, each being approximately 2.7 m (9 ft) long. 4. Insert the first string into the anchor hole in the upper part of the spool. Wind the f

Summary of the content on the page No. 17

MAINTENANCE CLEANING THE EXHAUST PORT AND SILENCER LATCH Depending on the type of fuel used, the type and amount of oil used and/or your operating conditions, the exhaust port and silencer may become blocked with carbon deposits. If you notice a power loss with your petrol-powered tool, a PULL COVER qualified service technician will need to remove these TO OPEN deposits to restore performance. SPARK ARRESTER The spark arrester must be cleaned or replaced every 25 hours or yearly to ensure proper

Summary of the content on the page No. 18

MAINTENANCE FUEL CAP STORAGE (1 MONTH OR LONGER) 1. Drain all fuel from tank into a container approved for petrol. Run engine until it stops. WARNING: 2. Clean all foreign material from the trimmer. Store it in a A leaking fuel cap is a fire hazard and must be well-ventilated place that is inaccessible to children. replaced immediately. Keep away from corrosive agents such as garden chemicals and de-icing salts. 3. Abide by all ISO and local regulations for the safe The fuel cap contains a no

Summary of the content on the page No. 19

TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORISED SERVICE DEALER. PROBLEM PROBLEM POSSIBLE CAUSE POSSIBLE CAUSE SOLUTION SOLUTION PROBLEM PROBLEM PROBLEM POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE SOLUTION SOLUTION SOLUTION Engine will not start: 1. No spark. 1. Check spark. Remove sparking plug. Reattach the sparking plug cap and lay sparking plug on metal cylinder. Pull the starter rope and watch for spark at sparking plug tip. If there is no spark, repeat

Summary of the content on the page No. 20

TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORISED SERVICE DEALER. PROBLEM PROBLEM PROBLEM PROBLEM PROBLEM POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE POSSIBLE CAUSE SOLUTION SOLUTION SOLUTION SOLUTION SOLUTION String will not advance: 1. String welded to itself. 1. Lubricate with silicone spray. 2. Not enough string on spool. 2. Install more string. Refer to “String Replacement” earlier in this manual. 3. String worn too short. 3. Pull strings w


Alternative user manuals
# User manual Category Download
1 Homelite UT15160 User manual Brush Cutter 97
2 Homelite UT15159R User manual Brush Cutter 45
3 Homelite UT15157 User manual Brush Cutter 25
4 Homelite UT15204 User manual Brush Cutter 22
5 Homelite UT15154 User manual Brush Cutter 17
6 Homelite UT15152 User manual Brush Cutter 19
7 Homelite UT20694 User manual Brush Cutter 27
8 Homelite UT20693 User manual Brush Cutter 15
9 Homelite UT20701 User manual Brush Cutter 18
10 Homelite UT20697 User manual Brush Cutter 9
11 Homelite UT20695 User manual Brush Cutter 10
12 Homelite UT20700 User manual Brush Cutter 11
13 Homelite UT20699 User manual Brush Cutter 24
14 Homelite UT20705 User manual Brush Cutter 22
15 Homelite UT20703 User manual Brush Cutter 14
16 Alamo SR14 User manual Brush Cutter 1
17 Alamo SR20 User manual Brush Cutter 2
18 Alamo GR60 User manual Brush Cutter 2
19 Alamo GR72 User manual Brush Cutter 1
20 Alamo TW84 User manual Brush Cutter 2