Summary of the content on the page No. 1
Henny Penny Model MP-941/942/943/944
Henny Penny
Multipurpose Holding Cabinet
Model MP-941
Model MP-942
Model MP-943
Model MP-944
OPERATOR’S MANUAL
Summary of the content on the page No. 2
Model MP-941/942/943/944 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT: Any part of a new appliance, except baskets, lamps, and fuses, which proves to be defective in material or workmanship within two (2) years from date of original installation, will be repaired or replaced without charge F.O
Summary of the content on the page No. 3
Model MP-941/942/943/944 TABLE OF CONTENTS Section Page Section 1. INTRODUCTION ...........................................................................................................1-1 1-1. Multipurpose Holding Cabinet ...............................................................................1-1 1-2. Features...........................
Summary of the content on the page No. 4
Model MP-941/942/943/944 SECTION 1. INTRODUCTION 1-1. MULTIPURPOSE The Henny Penny Multipurpose Holding Cabinet HOLDING CABINET is a basic unit of food equipment designed to hold hot foods at proper temperature in commercial food operations. This cabinet will keep hot foods humid while maintaining temperature. As of August 16, 2005, the Waste Electrical and Electronic Equipment directive went into effect for the European Union. Our products h
Summary of the content on the page No. 5
Model MP-941/942/943/944 1-5. SAFETY The only way to ensure safe operation of the Henny Penny Multipurpose Holding Cabinet is to fully understand the proper installation, operation and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures. Where information is of particular importance or is safety related, the words NOTICE, CAUTION, or WARNING are used. Their usage is described below: SAFETY ALERT SYMBOL is used
Summary of the content on the page No. 6
Model MP-941/942/943/944 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Multipurpose Holding Cabinet. Installation of this unit should be performed by a qualified service technician. Do not puncture the skin of unit with drills or screws as component damage or electrical shock could result. 2-2. UNPACKING The Henny Penny Multipurpose Holding Cabinet ha
Summary of the content on the page No. 7
Model MP-941/942/943/944 2-2. UNPACKING (Continued) 4. Open drawers and remove the packing or literature that is inside. 5. Pull off any protective covering from the exterior of the cabinet. 6. Your multipurpose holding cabinet is now ready for location and setup. 2-3. ELECTRICAL The multipurpose holding cabinets are available from the factory as 120 VAC for domestic use, or 230 VAC for international use. The units are single phase and require a grounded (earthed)
Summary of the content on the page No. 8
Model MP-941/942/943/944 2-4. CABINET DIMENSIONS MP-941 103 2-3
Summary of the content on the page No. 9
Model MP-941/942/943/944 2-4. CABINET DIMENSIONS (Continued) 2-4 103
Summary of the content on the page No. 10
Model MP-941/942/943/944 SECTION 3. OPERATION 3-1. INTRODUCTION This section provides operating procedures for the multipurpose holding cabinets. Read the Introduction, Installation and Operation Sections, and all instructions should be followed before operating the cabinet. This section contains an explanation of all controls, components, and information on operating procedures and daily maintenance. 3-2. OPERATING Figure 3-1 identifies and
Summary of the content on the page No. 11
Model MP-941/942/943/944 3-2. OPERATING CONTROLS AND COMPONENTS (Continued) Figure 3-1 3-3. START-UP Before using the cabinet, it should be thoroughly cleaned as described in the cleaning procedures section of this manual. To put the cabinet into operation, move each POWER switch to th
Summary of the content on the page No. 12
Model MP-941/942/943/944 3-3. START-UP (Continued) 1. Turn the POWER switch to the ON position. 2. The display will show the time of day or “ON”. Press and hold the appropriate drawer button to view the actual temperature of the drawer. 3. When the temperature LED illuminates, the setpoint temperature has been reached and product can now be loaded into the drawer. 3-4. OPERATING WITH 1. Place the hot product inside one of the drawers. PROD
Summary of the content on the page No. 13
Model MP-941/942/943/944 3-5. CLEANING (Continued) 5. Clean the interior of the cabinet thoroughly with a cloth and soapy water. Do not use steel wool, other abrasive cleaners or cleaners/sanitizers containing chlorine, bromine, iodine or ammonia chemicals, as these will deteriorate the stainless steel material and shorten the life of the unit. Do not spray the unit with water, such as, with a garden hose. Failure to follow this caution coul
Summary of the content on the page No. 14
Model MP-941/942/943/944 3-6. OPERATION AND 2. While holding in on the drawer button, press and PROGRAMMING release the SET button. Now the setpoint temperature (Continued) will be blinking at a faster rate. Now release the drawer button. 3. Press the UP and DOWN buttons to change the setpoint temperature. 4. Once the desired setpoint temperature is reached, press the SET button to return to normal operation mode and the setpoint will be saved. Spec
Summary of the content on the page No. 15
Model MP-941/942/943/944 3-6. OPERATION AND Setting Control to the Correct Number of Drawers PROGRAMMING (Continued) The different models, MP-941, 942, 943, and 944, all use the same control board. The boards are programmed at the factory for the correct unit. But, should the unit show “E06” or some drawers will not heat, the board may not be programmed for the appropriate unit. The LED flashes at a fast rate for the drawer(s) not
Summary of the content on the page No. 16
Model MP-941/942/943/944 G L O S S A R Y HENNY PENNY HOLDING CABINETS air temperature probe a round device located inside the cabinet that measures the inside air temperature and sends that information to the control panel concentration ring assembly a metal assembly located in the water pan in the bottom of the unit that helps keep an even humidity level inside the cabinet clean water pan setpoint a preset temperature at which a sensor warns the operator that the water pan
Summary of the content on the page No. 17
Model MP-941/942/943/944 probe clip a metal holder that attaches to the outside of the control panel to hold the food probe when not in use; the clip is an optional accessory product load capacity the highest recommended number of pounds/kilograms of food product that can be safely held in the cabinet proof function a program used for allowing bread to rise relative humidity the humidity level outside the cabinet setpoint a preset temperature or humidity; the setpoint is a pro
Summary of the content on the page No. 18
Henny Penny Corporation P.O.Box 60 Eaton,OH 45320 1-937-456-8400 1-937-456-8402 Fax Toll free in USA 1-800-417-8417 1-800-417-8434 Fax www.hennypenny.com *FM05-017-E* Henny Penny Corp., Eaton, Ohio 45320, Revised 02-21-08
