Summary of the content on the page No. 1
Air Palm Nailer
93496
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical quest
Summary of the content on the page No. 2
Specifications CastAluminum Frame, Max.NailLengthand 3-½"Lx8 gauge Construction: SteelAir Inletand Magnetic Gauge: (nails notincluded) SteelNailHolder. Driver Stroke and 1/4" stroke, At ir InletDimensions: ¼" 18NPTFemale Inle Impacts per Minute: 1,000 Blows Per Minute Am ir Consumption:2: - 4 cf O* perating Air Pressure 70 - 125psi OH verallDimensions:3: -¼"W x4-¾"Lx5-¼"N. etWeight 2.65 Lbs * The air pressure setting must not exceed job site regulations/restrictions. The air pressure setting mus
Summary of the content on the page No. 3
6. Dress properly while working. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive work clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. Always wear work boots and work gloves. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask o
Summary of the content on the page No. 4
16. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Use proper
Summary of the content on the page No. 5
Warning: The warnings, cautions, and instructions discussed in this instruc- tion manual cannot cover all possible conditions and situations that may oc- cur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Air Pressure Supply This tool is designed to operate with a maximum air pressure of 125 psi. You must use an air regulator, set at 125 psi or below. Note: Performance of this tool ma
Summary of the content on the page No. 6
Operation NOTE: This tool is assembled when you receive it, and may be used immediately. However, we recommend that you install a quick disconnect adapter (not included) to the Air Inlet (23) before use. WARNING: Do not put a nail into the Air Palm Nailer until you are ready to work. WARNING: Do not point the Air Palm Nailer toward any person or animal. Severe injury may result in case of accidental ejection of a nail. 1. Attach the air supply hose (not included) to the tool. 2. Grip the base of
Summary of the content on the page No. 7
Maintenance 1. Place a few drops of light weight air tool oil (not included) into the Air Inlet (23) each time before using the tool. 2. After each use, drain any accumulated moisture from the tool, and spray a small amount of water displacing oil into and on the tool. Wipe clean. 3. Store tool in a safe location out of reach of children and unauthorized persons. Troubleshooting Tool will not operate. 1. Possible cause: Low or no air pressure. Solution: Check air compressor to be sure it is ope
Summary of the content on the page No. 8
Assembly Drawing PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS S
