Summary of the content on the page No. 1
Model No. GGBE14820
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
custo
Summary of the content on the page No. 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASSEMBLY . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight bench. 1. Read all instructions in this manual before 9. Make sure that the cables remain on the pul- using the weight bench. Use the weight leys at all times. If the cables bind as you are bench only as described in this manual. exercising, stop immediately and make sure that the cables are on the pulleys. 2. It is the responsibility of the owner to ensure that a
Summary of the content on the page No. 4
BEFORE YOU BEGIN ® Thank you for selecting the versatile GOLD’S GYM tions, please call our Customer Service Department toll- ® XR15 weight bench. The GOLD’S GYM XR15 weight free at 1-800-999-3756, Monday through Friday, bench offers a selection of weight stations designed to 6 a.m. until 6 p.m. Mountain Time (excluding holidays). develop every major muscle group of the body. Whether To help us assist you, please note the product model your goal is to tone your body, build dramatic muscle number
Summary of the content on the page No. 5
ASSEMBLY • As you assemble the weight bench, make sure all Make Things Easier for Yourself parts are oriented as shown in the drawings. Everything in this manual is designed to ensure • For help identifying small parts, use the PART that the weight bench can be assembled suc- IDENTIFICATION CHART. cessfully by anyone. However, it is important to realize that the versatile weight bench has many The following tools (not included) are required parts and that the assembly process will take for ass
Summary of the content on the page No. 6
2. Press two Base Feet (18) onto a Base (3) as 2 shown. 8 Attach a Support Upright (7) to the Base (3) with two M8 x 50mm Bolts (48), two M8 Washers (34), and two M8 Nylon Locknuts (35). Do not tighten the Locknuts yet. 40 Assemble the other Base (3) and Support Upright (7) in the same manner. 8 7 Set the Uprights (8) on the Bases (3) as shown. 20 Attach an Upright to a Base with two M10 x 48 48 95mm Bolts (40), an Upright Joint Plate (19), and 19 7 two M10 Nylon Locknuts (37). Attach the other
Summary of the content on the page No. 7
5. Press three 45mm Square Inner Caps (26) into 5 the Leg Lever (6). Press a 25mm Round Inner 37 Cap (47) into the Weight Tube (15). 26 6 Attach the Weight Tube (15) to the Leg Lever (6) with an M8 x 58mm Bolt (33), two M8 Washers 26 (34), a Spacer (29), and an M8 Nylon Locknut 34 25 41, (35). Press the 25mm Round Angled Cap (25) Lubricate 33 onto the end of the Weight Tube. 35 29 15 Lubricate an M10 x 68mm Bolt (41) with grease. 4 Attach the Leg Lever (6) to the Front Leg (4) with 34 26 the Bol
Summary of the content on the page No. 8
9. Attach the Seat (13) to the Bench Frame (1) with 9 two M6 x 16mm Screws (44), an M6 x 63mm 13 Screw (50), and an M6 Washer (45). 1 45 50 44 10. Slide the three Pad Tubes (22) through the holes 10 23 in the Leg Lever (6) and the Front Leg (4). Slide the six Foam Pads (23) onto the Pad Tubes. Press six 19mm Round Inner Caps (24) into the 6 ends of the Pad Tubes. 4 24 22 24 24 23 11. Attach the Curl Pad (12) to the Curl Post (5) with 11 two M6 x 16mm Screws (44). 12 44 5 12. Press a 25mm Round I
Summary of the content on the page No. 9
ADJUSTMENTS This section explains how to adjust the weight bench. Refer to the accompanying exercise guide to see the cor- rect form for each exercise. Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate- ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. ADJUSTING THE BACKREST To adjust the position of the Backrest (14), pull the Backrest Pin (38) out as far as it will go. Mo
Summary of the content on the page No. 10
ATTACHING THE CURL POST For some exercises, the Curl Post (5) must be 12 attached to the Front Leg (4). Remove the 50mm Square Inner Cap (27) from the Front Leg. Insert the Curl Post into the Front Leg and align the holes in the Front Leg and the Curl Post. Secure the Curl Post with the Curl Knob (31). Make sure that you fully 5 tighten the Knob. 27 When performing exercises that do not require the Curl Pad (12), remove the Curl Post (5) from the Front Leg (4) and insert the 50mm Square Inner C
Summary of the content on the page No. 11
NOTES 11
Summary of the content on the page No. 12
ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (GGBE14820) ® 2. The NAME of the product (GOLD’S GYM XR15 weight bench) 3. The SERIAL NUMBER of the product (see the front cover of this manual) 4. The KEY NUMBER and DESCRIPT
Summary of the content on the page No. 13
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. M8 Washer (34) 25mm Round Inner Cap (47) M4 x 16mm Screw (53) 38mm x 76mm Inner Cap (52) M6 x 16mm Screw (44) M6 Washer (45) M10 Washer (49) M6 x 38mm B
Summary of the content on the page No. 14
PART LIST—Model No. GGBE14820 R1002A Key No. Qty. Description Key No. Qty. Description 1 1 Bench Frame 29 1 Spacer 2 1 Crossbar 30 2 Adapter Bushing 3 2 Base 31 1 Curl Knob 4 1 Front Leg 32 2 Weight Rest 5 1 Curl Post 33 1 M8 x 58mm Bolt 6 1 Leg Lever 34 6 M8 Washer 7 2 Support Upright 35 5 M8 Nylon Locknut 8 2 Upright 36 2 Weight Clip Cover 9 2 Upright Plate 37 26 M10 Nylon Locknut 10 2 Backrest Frame 38 1 Backrest Pin 11 1 Adjustment Bracket 39 1 M10 x 156mm Bolt 12 1 Curl Pad 40 18
Summary of the content on the page No. 15
EXPLODED DRAWING—Model No. GGBE14820 R1002A 52 14 51 47 32 28 9 8 40 51 10 49 43 45 43 46 28 37 49 7 10 37 20 39 45 45 49 46 52 46 51 37 28 11 49 48 13 49 48 51 45 43 19 47 46 40 49 12 28 32 37 40 37 20 9 8 51 37 38 1 3 7 34 37 37 20 37 51 2 53 35 45 48 5 37 50 27 18 21 48 23 37 44 23 31 40 44 20 23 41 21 37 26 37 18 3 24 41 19 6 4 34 33 26 29 22 25 36 24 23 34 34 15 40 35 35 18 42 26 17 24 47 24 24 23 22 30 16 18 22 30 24 23
