Summary of the content on the page No. 1
950W SDS
ROTARY
HAMMER DRILL
MAG950HD
INSTRUCTION MANUAL
1
Summary of the content on the page No. 2
Contents Warranty 2 Warranty Power Tools Introduction 3 Whilst every effort is made to ensure your complete satisfaction with this tool, occasionally, due to the mass Environmental protection 3 manufacturing techniques, a tool may not live up to our required level of performance and you may need the Description of symbols 3 assistance of our service department. Specifications 3 This product is warranted for a 2-year period for home General safety rules 4 domestic use from the date of the or
Summary of the content on the page No. 3
Introduction Description of symbols Your new GMC power tool will more than satisfy The rating plate on your tool may show symbols. your expectations. It has been manufactured under These represent important information about the stringent GMC Quality Standards to meet superior product or instructions on its use. performance criteria. Wear hearing protection. You will find your new tool easy and safe to operate, Wear eye protection. and, with proper care, it will give you many years Wear
Summary of the content on the page No. 4
3. Personal safety General safety rules a. Stay alert, watch what you are doing and use WARNING. Read all instructions. Failure to follow all common sense when operating a power tool. instructions listed below may result in electric shock, fire Do not use a power tool while you are tired or under and/or serious injury. The term “power tool” in all of the the influence of drugs, alcohol or medication. A moment warnings listed below refers to your mains operated (corded) of inattention w
Summary of the content on the page No. 5
• If possible, always use clamps or a vice to hold your work. c. Disconnect the plug from the power source before making any adjustments, changing accessories, or • Always switch off before you put the drill down. storing power tools. Such preventive safety measures • Ensure that the lighting is adequate. reduce the risk of starting the power tool accidentally. • Do not put pressure on the drill, such that it slows the d. Store idle power tools out of the reach of children and motor down. A
Summary of the content on the page No. 6
The tool must be used only for its prescribed purpose. Unpacking Any use other than those mentioned in this Manual will Due to modern mass production techniques, it is unlikely be considered a case of misuse. The user and not the that your GMC Power Tool is faulty or that a part is missing. manufacturer shall be liable for any damage or injury If you find anything wrong, do not operate the tool until the resulting from such cases of misuse. parts have been replaced or the fault has been r
Summary of the content on the page No. 7
7. Selector button Know your product 8. Variable speed dial 1. On/Off trigger switch 9. Auxiliary handle 2. Lock on button 10. Adjustable depth gauge 3. Soft grip handle 11. Locking sleeve 4. Forward/Reverse lever switch 12. SDS Chuck adaptor 5. SDS Chuck 13. Chuck key 10 6 7 6. 4-Function selector 14. 13mm Keyed chuck 5 11 4 1 2 8 9 3 12 13 14 7
Summary of the content on the page No. 8
Auxiliary handle and depth gauge Installing and removing bits 1. Turn the auxiliary handle (9) anti-clockwise to loosen the CAUTION. Always ensure that the drill is switched off and collar and slip it over the chuck onto the drill (Fig. A). plug is removed from the power socket before installing or removing drill bits. 2. Insert the depth gauge (10) in the hole at the top of the ® handle (9) (Fig. B). The drill features an SDS-Plus system which enables easy and safe bit replacement. ® B Bef
Summary of the content on the page No. 9
4. To select reverse, push the forward/reverse lever switch Operation (4) to the right side of the tool (Fig. L). Starting and stopping 5. When the switch (4) is left in middle position, it locks the H 1. Plug the cordset into the motor (Fig. M). mains socket. 2. Depress the on/off trigger L M switch (1) to start the drill and release the trigger when you wish to stop (Fig. H). Variable speed 1. The speed of the drill can be adjusted using the variable speed dial (8). 2. To increase t
Summary of the content on the page No. 10
Selecting the required function Hints for use It is possible to use the rotary Note. When drilling into masonry, the drilling rate is fast P hammer drill in four different and burnout of the tip will occur if the drill bit is not modes of operation: constantly cleared. 1. Rotation only • Use only correctly sharpened T drill bits, which are suitable for Non hammer action, non pneumatic the material being drilled. For drilling into metal and wood • To drill hard materials, firm products, c
Summary of the content on the page No. 11
Fitting the keyed chuck Maintenance The keyed chuck (14) supplied as an accessory can be WARNING. Always ensure that the tool is switched off and fitted to the SDS chuck with the use of the SDS chuck the plug is removed from the power socket before making adaptor (12). any adjustments or maintenance procedures. 1. The keyed chuck allows bits with a straight shank to be Store the tool, instruction manual and accessories in a used with the tool. secure place. In this way you will always have al
Summary of the content on the page No. 12
GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www.gmcservice.com.au. Should you not have access to the Internet, please contact our service department on 1300 880 001 (Australia) or 0800 445 721 (New Zealand). 7am –7pm, 7days a week (AEST). Please n
