Summary of the content on the page No. 1
O Owner's Manual wner's Manual
w with Assembly Instructions ith Assembly Instructions
F For Model P4266 or Model P4266
• • P Please r lease read this man ead this manual and ual and
s sa av ve e it with y it with your or our original iginal
s sales r ales receipt. eceipt.
• • T To ools needed f ols needed for assemb or assemblly y: :
a assemb ssemblly y wr wrenc ench (inc h (included) luded)
and a Phillips Scr and a Phillips Scre ew wdr driv iver er
(not inc (not included). luded).
®
Summary of the content on the page No. 2
TABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Parts Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
ELECTRICAL HAZARD DANGER • To reduce the risk of fi re or electric shock, carefully follow these instructions. To prevent electric shock, do not immerse in water; wipe clean with a damp cloth. WARNING • Battery can fall out and injure a child if vehicle tips over. Always close battery door. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fi re resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger cou
Summary of the content on the page No. 4
PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Vehicle Frame Tail Seat 2 Shocks Steering C
Summary of the content on the page No. 5
2 Front Hubcaps 2 Sidebar Covers Steering Wheel Cap 2 Rear Hubcaps (Left and Right) Assembly Wrench 2 Bushings 2 Front Axle Fastener Caps 2 Rear Axle Caps 12V Battery 12V Charger Part Not Shown: Label Sheet 3 3 3 #8 x /4" Screw - 32 #8 x /4" Black Screw - 8 /8" Lock Nut - 4 Fasteners Shown Actual Size For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. P4266pr-0920 5
Summary of the content on the page No. 6
PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 22 15 15 3 23 2 4 21 17 5 13 1 14 24 12 16 27 28 11 20 19 10 18 25 26 6 9 7 8 1 Vehicle Frame 10 Front Fender - 2 19 Front Axle Fasterner Cap - 2 28 Assembly Wrench 2 Tail 11 Rear Axle 20 Rear Axle Cap - 2 3 Seat 12 Sidebar - 2 21 12V Charger Parts Not Shown 4 Steering Post 13 Sidebar Cover - 2 22 Steering Wheel Cap Label Sheet 5 Hood 14 Long Seat Belt 23 Steering Wheel 3 #8 x /4" Black Screw - 8 6 Bumper
Summary of the content on the page No. 7
BATTERY CHARGING ELECTRICAL HAZARD WARNING CAUTION • Battery can fall out and injure a child if Use the charger in dry locations only. vehicle tips over. Always close battery door. • PREVENT FIRE About Thermal Fuses - Never modify the electrical system. ® Your Power Wheels 12 volt battery is equipped with a built-in Alterations could cause a fi re resulting thermal fuse. The thermal fuse is a self-resetting safety device in serious injury and could also ruin the which automatically “trip
Summary of the content on the page No. 8
ASSEMBLY Charger B WARNING Children can be harmed by small parts, sharp edges and sharp points in the vehicle's unassembled state, or by electrical items. Battery Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, A or help in assembly of the vehicle. Charger Connector Motor Rear Axle A • Plug the charger connector into the battery . B • Plug the charger into a standard wall outlet . Notes: - Use the charger
Summary of the content on the page No. 9
Rear Axle Cap Rear Hubcap 5 3 • Fit the tabs on the rear hubcap into the slots in the rear • Fit a rear axle cap onto the end of the rear axle. wheel. Push to "snap" into place. • Repeat steps 2-5 to assemble the other rear wheel, rear axle cap and rear hubcap to the rear axle. Front Axle 4 6 Front Axle • Insert a #8 x ¾" screw into the hole in the rear axle and tighten. • Pull to rotate the front axles completely towards the front of the vehicle. P4266pr-0920 9
Summary of the content on the page No. 10
Front Axle Fastener Cap Front Axle 7 Bushing 9 • Fit a front axle fastener cap onto the upper portion of a front axle. • Remove the cap on the end of the front axle. Dispose of the cap in the trash. • Slide a bushing, ring end first, onto a front axle. 8 • Align the hole in the axle fastener cap with the hole in the front axle. Hint: You may need to push the front axle towards the front of Front Wheel 10 the vehicle while you insert the screw. • Insert a #8 x ¾" screw into the large openi
Summary of the content on the page No. 11
Rim 11 • Slide a rim, indented side out, onto the front axle. 13 • Test to be sure the wheel spins. Lift the front end of the vehicle up slightly and turn the wheel. It should spin freely. • If the wheel does not spin freely, use the assembly wrench 1 to loosen the lock nut a /4" turn. Spin the wheel again and loosen more, if necessary. Assembly Lock Nut Wrench Front Hubcap 12 • Fit a lock nut onto the end of the front axle and tighten with the assembly wrench. 14 IMPORTANT! Fully tight
Summary of the content on the page No. 12
Tail Post Shock Slot SIDE VIEW 17 • First, fit the bottom of a shock into the slot next to the tail. • Then, slide the top of the shock onto the post on the tail. FRONT VIEW 15 • Fit the tail into the slots in the back end of the vehicle frame. DO NOT insert a screw here. Screw 18 • Insert a #8 x ¾" screw into the hole in the shock and tighten. Note: Do not insert a screw into the upper portion of the shock in this step. A screw will be assembled in this location in step 24. 16 • Repeat ste
Summary of the content on the page No. 13
Short Seat Belts F Folded olded Ta Tab b Rear Fenders 21 Folded Folded E End nd • Fit the rear fenders under the tabs the sides of the seat, as shown. 19 Note: Make sure the fasteners on both short seat belts face each other. • Fit the folded end of each short seat belt down through the outer slots in the seat. Do not insert the folded tab into the slot. Pull up on each seat belt to make sure it is secure. DO NOT insert screws here. 22 • Insert two #8 x ¾" screws into the upper hole in eac
Summary of the content on the page No. 14
Sidebar Cover Sidebar Cover 26 24 • Fit the sidebar covers onto the sidebars, as shown. • Insert eight #8 x ¾" screws into the seat and tighten. Hint: The sidebar covers are designed to fit one way. If a sidebar cover does not seem to fit, try the other one! • Insert a #8 x ¾" screw into each sidebar cover and tighten. Sidebar with Sidebar with Curve Out Curve Out Front Fenders T Ta abs bs 25 • Fit the sidebars into the slots in the vehicle frame and 27 rear fenders. Hint: Each sidebar is d
Summary of the content on the page No. 15
Hood Pegs 30 • Fit the tabs on the hood onto the pegs on the front fenders. TOP SIDE VIEW 28 • Insert six #8 x ¾" screws into the fenders and tighten. 31 • Fit the folded end of the strap attached to the hood up into the slot in the front end of the vehicle. Bumper FRONT VIEW 29 • Fit the bumper onto the front end of the vehicle. • Insert four #8 x ¾" screws into the bumper and tighten. P4266pr-0920 15
Summary of the content on the page No. 16
Steering Post Steering Column 32 Steering Column • Insert the straight end of the steering column up through the 34 bottom of the steering post, as shown. • Push the steering column down (so that it inserts into the Steering slot in the steering linkage underneath the vehicle). Column Post Lock Nut Steering Column Bend in Steering Column Slot Hole TOP SIDE VIEW 33 • Pull the straight end of the steering column up so that only the bend is visible (out from the bottom of the steering colum
Summary of the content on the page No. 17
Steering Column Lock Nut Assembly Wrench 38 • Fit a lock nut onto the end of the steering column and tighten Screws with the assembly wrench. Steering Wheel Cap 36 • Insert four #8 x ¾" screws into the holes in the bottom of the vehicle (to hold the steering column post and seat) and tighten. Steering Wheel 39 • Fit the steering wheel cap to the center of the steering wheel. Push to "snap" into place. INSIDE VIEW 37 • Turn the vehicle upright. • Fit the steering wheel onto the steering colu
Summary of the content on the page No. 18
DECORATION • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles. 4 5 6 8 9 11 10
Summary of the content on the page No. 19
14 18 3 3 RIGHT SIDE VIEW 15 19 3 3 LEFT SIDE VIEW P4266pr-0920 19
Summary of the content on the page No. 20
BATTERY INSTALLATION ® IMPORTANT! Use only a Power Wheels 12 volt lead-acid rechargeable battery. Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 ® hours using the enclosed Power Wheels 12 volt charger before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instructions may damage your battery and
