Summary of the content on the page No. 1
Product features and decoration may vary from the picture above.
™
®
Owner’s Manual with Assembly Instructions
Please read this manual and save it with your original sales receipt.
For Model 74526
Tools needed for assembly: Cap Nut Assembly Tool (included), Phillips Screwdriver, Hammer, and
®
Safety Scissors (not included). Use only with Power Wheels 12 Volt Lead-acid Rechargeable Battery and
®
Power Wheels 12 Volt Charger with Type “12V” Connector (included). Requires three size “AA” alkaline
Summary of the content on the page No. 2
Table of Contents A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Warnings B WARNING • Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. • Keep small parts and plastic bags out of children’s reach. Dispose of plastic bags properly. • Adult supervision is required. Children do not have the judgement necessary to avoid many accident
Summary of the content on the page No. 4
Pb Parts C • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. 12 Volt Charger 12 Volt Battery Vehicle Bo
Summary of the content on the page No. 5
Parts Rear Bumper Knob Plate Seat Dash Cap Nut Assembly Tool Steering Wheel Steering Column Cap Nut – 3* Dash Knob – 2 Key Assembly Hood Sound Box Brush Guard Spacer Tube – 2 Hood Latch – 2 Steering Wheel Cover Not Shown: Label Sheet *For your convenience, an extra .354 cap nut has been included. 5
Summary of the content on the page No. 6
Parts Windshield Frame - Front Windshield Frame - Back Windshield Hinge Pin – 2 Sport Bar Sport Bar Support - 2 Sport Bar Bracket Set Windshield Bracket – 2 Brush Guard Right Sidepipe Canopy Left Sidepipe 6
Summary of the content on the page No. 7
Parts 1 #10 x /2" Screw – 2 #8 x4" Screw – 2 1 3 1 #8 x 1 /4" Screw – 10 #8 x /4" Screw – 6 #6 x 1 /2" Screw – 4 1 1 1 /2" x /4" Machine Screw - 2 #8 x 1" Screw – 11 #10 x 1" Screw – 4 All Screws Shown Actual Size 7
Summary of the content on the page No. 8
Parts Diagram D D 43 38 33 37 28 43 33 32 36 21 32 35 33 15 10 46 31 15 23 29 30 31 3 24 10 20 19 17 27 13 16 18 22 10 12 11 14 45 6 13 8 4 9 10 5 10 25 26 1 44 40 41 39 34 7 44 40 13 42 2 3 Jeep® Sandblaster ™ MODEL 74526 8
Summary of the content on the page No. 9
Parts Diagram No. Part Quantity No. Part Quantity 28 Windshield Frame, Front 1 1 Vehicle Body 1 29 Windshield Bracket 2 2 Steering Column 1 30 Sport Bar 1 3 Cap Nut 2 31 Sport Bar Support 2 4 Hood Latch 2 32 Sport Bar Bracket 2 5 12 Volt Battery 1 1 33 #6 x 1 /2" Screw 4 6 Battery Retainer 1 1 1 34 1 /2" x /4" Machine Screw 2 7 #8 x 4" Screw 2 ™ 35 KC Light Rack, Front 1 8 Taillight Lens 2 ™ 36 KC Light Rack, Rear 1 9 Taillight Housing 2 37 Light Cover 2 10 #8 x 1" Screw 11 38 Windshield Frame,
Summary of the content on the page No. 10
Battery Charging E About Thermal Fuses ® WARNING Your Power Wheels 12 volt battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting safety device which automatically “trips” and shuts down • The battery must be handled by adults operation of the vehicle if the vehicle is overloaded or the only. The battery is heavy and contains driving conditions too severe. Once a fuse has “tripped”, it sulfuric acid (electrolyte). Dropping the will automatically reset itself after
Summary of the content on the page No. 11
Pb Battery Charging Important Notes • Your new battery must be charged for at least 18 hours before you use it in your vehicle for the first time. • You do not need to remove the battery from your vehicle to recharge it. 2 Battery • The battery must be upright while charging. • The charger is not a toy. • Do not short circuit the battery. • We recommend that you start charging your battery 1 before beginning assembly of your new vehicle. • Before charging the battery, examine the battery case f
Summary of the content on the page No. 12
Assembly F Do not omit any steps. Please set aside at least 60 minutes for assembly. 2 Dash Rear of Vehicle 1 1 3 2 Left Sidepipe 1 Tab Channel Cover Screw Pegs 1 2 Vehicle Body • Position the dash on the vehicle body. Make sure the holes in the dash tabs align with the holes in the vehicle • Turn the vehicle body upside down. body and that the channel cover is captured by the dash. • Fit the left sidepipe under the left (driver) side of the • Insert two #10 x 1" screws through the holes towards
Summary of the content on the page No. 13
Assembly Battery Microphone Compartment 7 5 Dash Door Battery Compartment Sound Box • Bend the plastic tip on the end of the microphone cord so 3 x 1.5V that it forms a “T”. “AA” (LR6) • Fit the “T” end of the microphone cord down through the hole in the dash pocket. Pull up gently on the microphone cord to make sure the end is secured in SHOWN ACTUAL SIZE the dash. • Loosen the screw in the sound box’s battery • To hang the microphone on the dash, fit the hook on the compartment door using a
Summary of the content on the page No. 14
Assembly Hole Cap 8 10 Steering Nut Wheel Steering Column Cap Nut Assembly Tool Steering “UP” Column Bottom View • Turn the vehicle body upright. • Position the steering wheel upright (see inset). • Wipe the steering column with a paper towel to remove • Fit the steering wheel onto the steering column. any excess lubricant. • Fit a cap nut into the cupped end of the cap nut • Turn the vehicle body on its side. assembly tool. • Insert the straight end of the steering column up through • Tap the
Summary of the content on the page No. 15
Assembly Wide Tab Wide Notch 14 12 Headlight Lens Lens Guard • Fit the wide notch in the side of a headlight lens under Brush Guard Bumper the wide tab on a lens guard. • Press firmly on the inside of the headlight lens to snap it into the lens guard. • Repeat this procedure to assemble the other headlight lens to the remaining lens guard. • Fit and hold the brush guard against the front bumper. • Insert two #10 x 1" screws through the front of the brush guard and into the bumper. Grille 13 • Ti
Summary of the content on the page No. 16
Assembly Windshield Frame - Front Half Hood Latch 18 16 Hole Slots Tabs Hood Latch • Insert a hood latch into one of the holes in the vehicle • Align the slots in the front half of the windshield frame body, near the hood area. with the tabs on the windshield brackets. 1 4 • Twist the base of the hood latch / turn to secure it in the • Fit the front half of the windshield frame onto the vehicle body. windshield brackets as shown. • Repeat this procedure on the other side of the hood area to atta
Summary of the content on the page No. 17
Assembly Short Seat T-Loop (Pull through slot) Windshield Frame – Back Half Belt Strap 22 20 Fastener End End T-Loops Slots Windshield Frame – Front Half Seat Slot • Turn the seat upside down. • Insert the fastener end of a short seat belt strap through the slot near the outer edge of the seat. Make sure the • Fit the back half of the windshield frame onto the front side of the seat belt with the fastener faces the outer half of the windshield frame. Make sure the slots at the edge of the seat.
Summary of the content on the page No. 18
Assembly Canopy Sleeves Seat 24 26 Seat Back Tabs Canopy Sleeves Tabs PUSH 3 HERE Canopy 2 Slot 1 Sport Bar • With the seat at an angle, insert the tabs on the front 1 edge of the seat into the slots in the foot-well wall . • Position the sport bar on its side so that the sport bar ends curve away from you. • Push down firmly on the edge of the seat above each 2 tab to snap the tabs into the slots . • Position the canopy opposite the sport bar with the netting facing away from you. • Rotate the
Summary of the content on the page No. 19
Assembly TM KC Light Sport Bar Bracket Rack - Back Half 28 30 Ring Tab Tabs Hole Tunnel Side Leg Sport Bar Sport Bar Support TM KC Light Rack - Front Half • Using safety scissors, remove the sport bar brackets from • Position the sport bar upright, as shown. the plastic connector. Dispose of the plastic connector. TM • Position the sport bar upright. • Fit and hold the front and back halves of the KC light TM rack against the sport bar. Make sure the two KC light • Fit a sport bar support throug
Summary of the content on the page No. 20
Assembly 32 34 Sport Bar Rear Bumper PUSH HERE Side Fender Tabs Rear Bumper Support PULL HERE Lower Rail • Face the rear of the vehicle. • Fit the lower rail on the rear bumper over the rear bumper support. • Fit the sport bar and sport bar support legs into the holes • Gently bend the tabs at the bottom of the rear bumper in the vehicle body. under the vehicle. • Push down firmly on a sport bar side leg while pulling up on the side fender to fit the sport bar into the vehicle body. • Repeat
