Summary of the content on the page No. 1
M2055
www.fisher-price.com/uk
Summary of the content on the page No. 2
Consumer Information IMPORTANT! Please keep these instructions for future reference, as they contain important information. • Please read these instructions before use of this product. • Adult assembly is required. Tool needed for assembly: WARNING Phillips Screwdriver (not included). • Requires three “C” (LR14) alkaline batteries (not included) To prevent serious injury or death: for operation. • Fall Hazard - It is dangerous to use • Product
Summary of the content on the page No. 3
Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed inside the pad. Butterfly Toy Infant Support Seat Back Tube Toy Bar Seat Pad Base Tube Soothing Unit Front Base 4 mm x 0 mm Screw – 2 4 mm x 20 mm Screw – 2 Shown Actual Size
Summary of the content on the page No. 4
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Front Base DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Turn Tube Ends Up Seat Back Tube Handles 2 •I nsert the ends of the front base into the holes in the handles. Hint: If you cannot insert the front base into the handles, turn
Summary of the content on the page No. 5
Assembly Back Base PRESS PRESS Front Base Soothing Unit Groove Handle Tubes 4 • While pressing the buttons on the ends of the back base, • T urn the assembly upright. insert it into the tubes in the handle. Make sure the back • P osition the soothing unit upright and fit the groove to the base “snaps” into place. front base, as shown. • Pull the back base to be sure it is secure to the handle tubes. • Inser t two 4 mm x 30
Summary of the content on the page No. 6
Assembly Upper Flap Seat Back Tube Front Base Lower Pocket 5 Strap • F it the upper flap on the pad around the seat back tube. Side Flap 6 • F it the pad lower pocket around the front base and soothing unit. • T urn the assembly face down. • F asten both pad side flaps to the strap on the back of the pad. Make sure you hear a “snap” on both sides. PRINTED IN CHINA M2055pr-0726
Summary of the content on the page No. 7
Assembly B Infant Support Toy Bar A Socket 8 • Place the infant support on top of the pad. • Inser t the restraint pad through the slot in the infant support. Make sure the restraint pad is not twisted. • Thr ead the restraint straps through the slots in the infant support. Assembly is now complete. • F it the toy bar into the socket in the handle A. Turn the toy bar to secure in place B. • Attac h the butterfly toy
Summary of the content on the page No. 8
Battery Installation 1.5V x “C” (LR14) Battery Compartment Hint: We recommend using an alkaline batteries for longer battery life. • Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). 2 • Loosen the screw in the battery compartment door and remove the battery compartment door. • Inser t three “C” (LR14) alkaline batteries into
Summary of the content on the page No. 9
Setup and Use Restraint Pad WARNING To prevent serious injury or death: • Fall Hazard - It is dangerous to use this reclined cradle on an elevated surface, since child’s movement may cause product to slide or tip over. Use only on a floor. • Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion) Restraint Straps since the product can tip over and cause suffocation in soft surfaces. 1 • Never use the toy bar a
Summary of the content on the page No. 10
Soothing Unit Storage Button Back Tube • While pressing the buttons on the handles, push the back tube towards the front tube. Hint: To set-up this seat again, simply pull the back tube • Mak e sure your child is properly secured in the seat. back until it “snaps” into place. • Slide the power switch to for music. • Slide the power switch to for vibrations. • Slide the power switch to music and vibrations. • Slide the power switch
Summary of the content on the page No. 11
Care • The pad, butterfly and infant support are machine washable. Wash them separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. • The frame and toy bar may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. 1 To remove the pad: • Place the sea
Summary of the content on the page No. 12
www.service.fisher-price.com/uk 01628 5000 GREAT BRITAIN Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303; www.service.mattel.com/uk. AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND 16-18 William Pickering Drive, Albany 1331, Auckland. ASIA Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
