Summary of the content on the page No. 1
I n s t a l l a t I o n I n s t r u c t I o n s
Wa r m I n g o v e n
For use with models:
EW, EWO
MW, MWO
PW, PWO
IWO, IOWO
Part No. 65034 Rev. K
Summary of the content on the page No. 2
t elba fo c netntso Important Safety Instructions .....................................................1 Installation Instructions ............................................................7-8 Design Specifications ...............................................................2-3 Verifying the Package Contents .................................................7 Product Dimensions .................................................................2-3 Removing the Drawer ........................
Summary of the content on the page No. 3
Important s afety Iutnrcst Ison Safety Symbols and Labels Important Irfontam Ion a bout DANGER s ytefa Irtntsuc Isno Immediate hazards that WILL result in severe personal injury or death. Important Safety Instructions and warnings appearing in these instructions are not meant to cover all possible conditions and WARNING situations that can occur. Common sense, caution and care must be exercised when installing, maintaining or operating an Hazards or unsafe practices that COULD result in
Summary of the content on the page No. 4
Des Ign s cpe If Icta Inos p or Dtcu DIensm Ions NOTE: All tolerances are + 1/16,” - 0” unless otherwise stated. Overall Dimensions (EW, EWO, MW, MWO, PW, PWO) 40" (1016mm) 3 prong 120 Vac power cord 9" Mounting 10 1/8" 1/2" (229mm) holes (257mm) (13mm) 10" (254mm) Chassis view without drawer Drawer Face Dimensions 1/2" (13mm) (MW Shown) Chassis Dimensions EW EWO PWO MWO PW MW 3 5/16" 2 3/16" 1 5/16" 3 7/16" 3 1/4" 2 1/4" D (84mm) (56mm) (33mm) (87mm) (83mm) (57mm) E 1" 1" 1" 1" 1 5/32" 1 1/8
Summary of the content on the page No. 5
Des Ign s epc If Icat Ison Overall Dimensions (IWO, IOWO) 40" (1016mm) 3 prong 120 Vac power cord Mounting holes (rear holes IOWO model only) F K C Chassis view without drawer Drawer Face Dimensions (IWO Shown) Chassis Dimensions (IOWO Shown) E G Chassis NOTE: Only model IOWO24 warming ovens are approved for outdoor use. They are designed for installation of a custom designed drawer front or for ® the Dacor Epicure drawer front and handle. Order accessory model number AEWP24 through your D
Summary of the content on the page No. 6
Installat Ion s pec If Itca Inos Itstallan Ino p nnal Ign ◊ A qualified technician must complete the installation of this built-in appliance. Proper installation is the responsibility of the customer. ◊ Carefully check the installation location. The oven should be placed for convenient access. Make certain that electrical power can be provided in the selected location. 1 ¾” Min. 27"/30"/36" Dacor (44mm) ◊ Plan the installation so that all minimum clearances are single oven met or exc
Summary of the content on the page No. 7
Installat Ion s pec If Itca Iosn 1 1/2" (38mm) Typical countertop Cooktop 3/4" Min. (19mm) Warming Oven C 5/8" Min. (16mm) 120 Vac 36" Typ. electrical (914mm) A outlet B Single Installation to Side of Cooktop OB Outdoor Grill EG Epicure Gas Cooktop 3/4" Min. (19mm) Warming Oven C 36" typ. D (914mm) 120 Vac electrical Warming Oven C outlet 5/8" Min. (16mm) A B Stacked Installation Below Cooktop or Grill 5
Summary of the content on the page No. 8
Installat Ion s epc If Icat Ison The correct voltage, frequency and amperage must be supplied p o Wre s ylppu r que Iementsr to the electrical outlet from a grounded, single phase circuit that is protected by a properly sized circuit breaker or time-delay fuse. WARNING Electric shock Hazard – This appliance is equipped Circuit Requirements: with a 40” (1016mm) power cord with a three prong grounded plug. Plug it only into a grounded three prong ◊ 120 Vac, 60 Hz, 15 Amp. dedicated circuit
Summary of the content on the page No. 9
Itnstalla Ino Icnsttur Inso v er Ify Ign hte p kageac c tnteosn Install Ign het c assh Is • Use and care manual WARNING • Mounting screws To avoid personal injury caused by the appliance • Wire rack with mounting hardware (IOWO model only) falling forward when the drawer is opened, secure the chassis to the cabinet and support platform as r move Ign teh Dar Wre instructed. WARNING 1. Verify that the electrical outlet for the warming 1. Grasp the warming oven chassis on opposi
Summary of the content on the page No. 10
Itnstalla Ion Itnstruc Ions r e -Ilnstal Ing the Dra Wre Ianstallt Ion c lheck Its 1. Pull the drawer slides all the way out of the drawer WARNING opening. To ensure a safe and proper installation, the 2. Gently lower the drawer between the extended slides following checklist should be completed by the until the drawer is suspended by the slide rails. installer to ensure that no part of the installation 3. Slide the back of the drawer mounting brackets under has been overlooked. the drawe
Summary of the content on the page No. 11
Summary of the content on the page No. 12
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
