Summary of the content on the page No. 16
GENERAL ASSEMBLY - TILTING MODELS (pg. 2 of 3) 25 26 27 28 29 30 23 24 BB CC 21 22 15 16 17 18 19 20 37 38 39 40 41 36 42 43 45 43 42 46 47 48 49 50 58 53 59 31 44 32 33 34 35 60 51 52 53 54 13. FI05198-5 COMPRESSION ELBOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 14. FI00565-6 NIPPLE 3/8 NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 15. FI05222 SWIVEL ELBOW . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 17
GENERAL ASSEMBLY - TILTING MODELS (pg. 3 of 3) 23. FA19177 HEX SOCKET SET SCREW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 24. FA20047 JAM NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 25. KE50294-1 MERCURY SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 26. KE54456-1 MERCURY SWITCH BRACKET . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 18
GENERAL ASSEMBLY - STATIONARY MODELS (pg. 1 of 2) VIEW "B" 34 31 5 7 8 10 L3 MANIFOLD & BURNER TUBE PIPING DETAIL 21 A 25 6 7 9 10 L1 27 14 15 16 26 28 29 28 30 VIEW "A" COMPONENT MOUNTING BOX WITH LID REMOVED 11 2 3 4 32 13 19 20 12 23 33 24 25 17 18 L4 L2 B 22 1 15
Summary of the content on the page No. 19
GENERAL ASSEMBLY - TILTING MODELS (pg. 2 of 2) ITEM NO. PART NO. DESCRIPTION QTY. 1. KE00099 ADJUSTABLE FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2. KE01928-2 COMPONENT MOUNTING PLATE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . .1 (see COMPONENT MOUNTING PLATES on page #9) 3. FA20006 MACHINE SCREW NUT (10-24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. FA32006 TOOTH LOCK WASHER . . . . . . . .
Summary of the content on the page No. 20
CONSOLE CONTROLS 4 7 8 1 5 7 3 2 6 7 ITEM NO. PART NO. DESCRIPTION QTY. 1. SE00114 POTENTIOMETER WITH ON/OFF SWITCH, C/W ITEM #2 . . . . . . . . . . . . . . . . .1 2. KE51005 RUBBER BOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE50569-1 KNOB, POTENTIOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 4. KE50567-1 L.E.D., RED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 1
Operators Manual
Installation, Operation & Service
Gas 25 Gallon Kettle
MODELS:
KGL-25
KGL-25-T
KGT-25
KGT-25-T
1333 East 179th St., Cleveland, Ohio, U.S.A. 44110
Enodis
Phone: (216) 481-4900 Fax: (216) 481-3782
Visit our web site at www.clevelandrange.com
SE95052
Summary of the content on the page No. 2
FOR THE USER IMPORTANT! ENSURE KETTLE IS AT ROOM TEMPERATURE AND PRESSURE GAUGE IS SHOWING ZERO OR LESS PRESSURE PRIOR TO REMOVING ANY FITTINGS. WARNING: Improper installation, FOR YOUR SAFETY adjustment, alteration, service or maintenance can cause property DO NOT STORE OR USE damage, injury or death. Read the GASOLINE OR ANY OTHER FLAMMABLE LIQUIDS AND installation operating and VAPOURS IN THE VICINITY maintenance instructions OF THIS OR ANY OTHER thoroughly before installing or APPLIANCE.
Summary of the content on the page No. 3
TABLE OF CONTENTS Installation Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Shipping Damage Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
INSTALLATION INSPECTION INSTALLATION Before unpacking visually inspect the unit for evidence Note: For clearance requirements, suggested of damage during shipping. drain location and assembly details refer to "SPECIFICATION DRAWING" on page #3. If damage is noticed, do not unpack the unit, follow shipping damage instructions. 1. Position the unit in it's permanent location, and level the unit by turning the adjustable feet. SHIPPING DAMAGE 2. Once positioned 4 7/8" (124mm) and leveled, INSTRUCTI
Summary of the content on the page No. 5
ELECTRICAL INSTALLATION CHECKS Although the kettle has been thoroughly tested before ENSURE THE ELECTRICAL SUPPLY MATCHES THE leaving the factory, the installer is responsible for KETTLE'S REQUIREMENTS AS STATED ON THE RATING LABEL. ensuring the proper operation of kettle once installed. A cord and plug are supplied with the unit. Simply plug DO NOT ATTEMPT TO OPERATE THIS APPLIANCE the unit into any grounded outlet rated for a minimum of DURING A POWER FAILURE. 10 amps. See GENERAL ASSEMBLY (p
Summary of the content on the page No. 6
SPECIFICATION DRAWING - TILTING MODELS FOOT LOCATION & FLOOR DRAIN DETAIL FLANGED FOOT DETAIL NOTES OVERALL DEPTH SPECIFICATIONS 3
Summary of the content on the page No. 7
SPECIFICATION DRAWING - STATIONARY MODELS 7/16" (11 mm) Ø 4 7/8" 3 HOLES ON 124 Ø mm 3 1/8" (80 mm) Ø B.C.D. 120º TYP 1 5/8" (42 mm) Ø FOOT LOCATION & FLOOR DRAIN DETAIL 1" (25 mm) 9/16" MAX. ADJUSTMENT 14 mm FLANGED FOOT DETAIL SPECIFICATIONS NOTES 4
Summary of the content on the page No. 8
OPERATING INSTRUCTIONS 2 3 1 7 4 5 6 8 General Parts Drawing ITEM # DESCRIPTION FUNCTION 1. Tilt Wheel (tilting models only) Used for tilting the kettle. 2. Vacuum/Pressure Gauge Indicate steam pressure in PSI inside steam jacket as well as vacuum in inches of mercury. 3. Pressure Relief Valve This valve is used to vent the kettle and in the unlikely event there is an excess steam build-up in the jacket, this valve opens automatically to relieve this pressure. 4. Low Water Indicator Light (Re
Summary of the content on the page No. 9
NOTE: Do not fill kettle above OPERATING THE KETTLE recommended level marked on outside DO NOT ATTEMPT TO OPERATE THIS APPLIANCE of kettle. DURING A POWER FAILURE. NOTE: The Low Water Indicator Light (Red) (4) should not KEEP APPLIANCE AND AREA FREE AND CLEAR OF be lit during kettle operation. This light indicates that the COMBUSTIBLES. burners have been automatically shut off by the kettle's safety DO NOT LEAN ON OR PLACE OBJECTS ON KETTLE circuit. It is normal for the red light to come on when
Summary of the content on the page No. 10
CLEANING INSTRUCTIONS c) In a sink, wash and rinse the inside of the CARE AND CLEANING valve body using a nylon brush. Your kettle must be cleaned regularly to maintain its d) Reassemble the draw-off valve by reversing fast, efficient cooking performance, and to ensure its the procedure for disassembly. The valve's continued safe, reliable operation. hex nut should be hand tight only. 6. Rinse kettle interior thoroughly, then drain the rinse WARNING: Do not use chloride water. Do not leave water
Summary of the content on the page No. 11
SERVICE PARTS WARRANTY Our Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance and Repair Centre for replacement parts, service, or information regarding the proper maintenance and repair of your cooking equipment In order to preserve the various agency safety certification (UL, NSF, ASME/Ntl. Bd., etc.), only factory- supplied replacement parts should be used. The use of other than factory supplied replacement parts will void warranty. FAUCE
Summary of the content on the page No. 12
COMPONENT MOUNTING PLATES STATIONARY MODELS TILTING MODELS 3 4 5 10 10 11 12 13 8 7 4 2 5 9 3 5 10 1 7 8 1 2 6 9 ITEM NO. PART NO. DESCRIPTION QTY. 1. KE01927-1 COMPONENT MOUNTING PLATE (STATIONARY MODELS) . . . . . . . . . . . . . . .1 KE01927 COMPONENT MOUNTING PLATE (TILTING MODELS) . . . . . . . . . . . . . . . . . . .1 2. KE50753-7 RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE00458 SSK CONTROL BOX . . . . . . .
Summary of the content on the page No. 13
BURNER ASSEMBLY 11 7 8 10 17 16 15 2 3 1 4 5 6 12 14 13 9 ITEM NO. PART NO. DESCRIPTION QTY. 1. KE54897-1 MANIFOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE54890-1 IGNITION GUARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. FA11144 SCREW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 4. KE54881-1 BOTTOM COV
Summary of the content on the page No. 14
2" TANGENT DRAW-OFF VALVE 7 6 5 4 3 2 1 ITEM NO. PART NO. DESCRIPTION QTY. 1. - 7. KE50972-B DRAW-OFF ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1. FA95049 WING NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE527551 KNOB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE52754 HEX NUT . . . . . . . . . .
Summary of the content on the page No. 15
GENERAL ASSEMBLY - TILTING MODELS (pg. 1 of 3) 62 3 2 4 60 VIEW "G" MANIFOLD & BURNER TUBE PIPING DETAIL 55 56 57 10 8 13 12 11 12 14 L2 L3 5 60 L5 6 9 L4 7 G L1 61 1 ITEM NO. PART NO. DESCRIPTION QTY. 1. KE00099 ADJUSTABLE FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE51723-1 SAFETY VALVE (50 PSI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE50429-3 PRESSURE GAUGE . . . . . . . . . . . . . .
