Summary of the content on the page No. 1
Stitch welder
98753
Set up and Operating inStructiOnS
®
distributed exclusively by harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS manual.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the expre
Summary of the content on the page No. 2
nOtice is used to SaVe thiS manual address practices Keep this manual for the safety warn not related to personal injury. ings and precautions, assembly, operat cautiOn, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Summary of the content on the page No. 3
c. do not abuse the cord. never use This enables better control of the the cord for carrying, pulling or welder in unexpected situations. unplugging the welder. Keep cord e. dress properly. do not wear loose away from heat, oil, sharp edges or clothing or jewelry. Keep your moving parts. Damaged or entan- hair, clothing and gloves away gled cords increase the risk of electric from moving parts. Loose clothes, shock. jewelry or long hair can be caught in d. when operating a welder
Summary of the content on the page No. 4
the welder for operations different • Any power cord must be properly from those intended could result in a grounded. Ground Fault Circuit Inter hazardous situation. rupter (GFCI) should also be imple mented – it prevents sustained elec 5. Service trical shock. a. have your welder serviced by a 7. WARNING: The brass components qualified repair person using only of this product contain lead, a chemi identical replacement parts. This cal known to the State of California will ensure th
Summary of the content on the page No. 5
10. Do not exceed input amperage of 50 reach. Thoroughly clean the object Amps. being welded of any paint, grease, or other foreign material. 11. The warnings, precautions, and in structions discussed in this instruction 4. If working on a wall or ceiling prevent manual cannot cover all possible con ignition of combustibles on the other ditions and situations that may occur. side by moving them to a safe loca It must be understood by the operator tion. that common sense and caution are
Summary of the content on the page No. 6
12. Enclose the work area with portable 3. Wear suitable gloves to reduce the fire resistant screens. Protect com- vibration effects on the user. bustible walls, ceilings, floors, etc., 4. Use tools with the lowest vibration from sparks and heat with fire resis- when there is a choice between dif tant covers. ferent processes. 13. Use a nonconductive safety mat on 5. Include vibrationfree periods each the work surface to insulate the op day of work. erator from the work surface. 6. Grip
Summary of the content on the page No. 7
allow access by children or pets to SpeciFicatiOnS prevent injury and distraction. Maximum Amperage 55 A 2. Route the power cord along a safe 18 to 22 Gauge Sheet route to reach the work area without Material Range Metal creating a tripping hazard or exposing 1/16” Diameter, 6013 & Welding Rods the power cord to possible damage. 6014 (not included) The power cord must reach the work area with enough extra length to al low free movement while working. unpacKing 3. Secure loose work piec
Summary of the content on the page No. 8
welding rod into the tip of the Stitch the electrode to ground and turn the Welder. Secure the Rod Holder. Welder off. 6. Clamp the electrode holder of the 14. Place the Stitch Welder down on a ARC welder onto the Connection (11) nonflammable, nonconductive sur of the Stitch Welder. face to cool. 7. Adjust the output to no greater than 15. Read the included Weld Diagnosis 50 Amps. pamphlet for directions and welding guidelines. 8. danger! t o prevent serious 16. To prevent accidents, d
Summary of the content on the page No. 9
replaced only by a qualified ser- maintenance and vice technician. Ser Vicing pleaSe read the FOllOwing Procedures not specifically explained in this manual careFull Y must be performed only by a THE MANUFACTURER AND/OR DISTRIBUTOR qualified technician. HAs PRoviDED THE PARTs LisT AnD AssEMBL y DiAgRAM in THis MAnuAL As tO preVent A REfEREnCE TooL onL y. nEiTHER THE SeriOuS injur Y MANUFACTURER OR DISTRIBUTOR MAKES FrOm accidental ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
Summary of the content on the page No. 10
partS liSt partS liSt part description Qty. part description Qty. 1 Frame 1 11 Pig Tail 1 2 Front Cover 1 12 Guard 1 3 Back Cover 1 13 Handle 1 4 Solenoid 1 14 Insulator 1 5 Washer 1 15 Rod Holder 1 6 Axis Assembly 1 16 Screw M4x6 1 7 Plug Assembly 1 17 Nut M4 3 8 Contact 1 18 Lock Washer 2 9 Front Spring 1 19 Contact 1 10 Back Spring 1 diagram record product’s Serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and s
Summary of the content on the page No. 11
limited 90 da Y warrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installa
