Summary of the content on the page No. 1
FRAMING NAILER
21° ANGLE / 10 GAUGE
97511
93909
SET UP AND OPERATING INSTRUCTIONS
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shap
Summary of the content on the page No. 2
SPECIFICATIONS Nail Size .113” to .131” Thick Shank, 2” to 3-1/2” Long; 21° Full Head Magazine Capacity 60 Nails Operating PSI 70 to 125 PSI * Required Average Air Flow 3 - 3.5 CFM at 90 PSI Accessories 4 Hex wrenches, safety goggles, oil dropper Features Full Sequential Safety Trip Mechanism, 360° Exhaust Flow Adjustment, Soft Rubber Grip, 1/4” NPT (18 NPT) Air Inlet with Screen, Adjustable Depth Drive * The air pressure setting must not exceed job site regulations/restrictions. The a
Summary of the content on the page No. 3
7. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 8. Use eye and ear protection. Always wear ANSI approved impact safety goggles and appropriate hearing protection. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Other people in the work area must also wear ANSI approved impact
Summary of the content on the page No. 4
impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the compressor without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your air compressor’s manual for the appropriate size cord. It is also possible that the use of an extension cord may cause your
Summary of the content on the page No. 5
workplace. Carry the tool by the handle and avoid contact with the trigger. Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which c
Summary of the content on the page No. 6
Testing The Full Sequential Safety Trip Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the Nailer at a piece of scrap wood when testing. 1. The Nailer should not fire if the nose is not depressed against the workpiece. This tool has a full sequential safety trip mechanism, which is designed to reduce the risk of inadvertent firing. The tool should only fire if the Safety (38) is resting on the workpiece prior to pulling the Trigger (44). 2. D
Summary of the content on the page No. 7
Loading Nails (continued) 3. Orient a strip of nails with the points down, and drop the strip of nails into the Magazine (71). (See Figure C.) 4. Slide the strip of nails forward in the Magazine (71). NOTE: The Magazine will hold 60, 10 gauge nails. (See Figure C.) 5. Unlatch the Feeder Shoe (52), and allow the Feeder Shoe to slide forward against the strip of nails. (See Figure C.) OPERATION NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page
Summary of the content on the page No. 8
EXHAUST COVER (4) NAILS (10 GAUGE) (2-3/16” TO 3-1/2” LONG) NOSE (29) FEEDER SHOE (52) QUICK COUPLER & AIR SUPPLY HOSE TRIGGER (NOT INCLUDED) (44) BRACKET A (35) NOSE (29) SAFETY (38) FIGURE B To Adjust The Depth To Which A Nail Is Driven 1. The depth to which a nail is driven is controlled by the Safety (38). (See Figures B and C). 2. To adjust the depth of drive, loosen the Screw (37). Slide Safety (38) up or down to the desired position. Then, re-tighten the Screw. Note: Sliding Sa
Summary of the content on the page No. 9
SCREW (37) SAFETY (38) RUBBER COVER (39) FIGURE C Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (71) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (71) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer. Clearin
Summary of the content on the page No. 10
FIGURE D Probe in these areas with a screwdriver to release jammed nails. Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (71) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine (71) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of
Summary of the content on the page No. 11
SKU 97511 93909 For Technical Questions, Please Call 1-800-444-3353 Page 11
Summary of the content on the page No. 12
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEM
