Summary of the content on the page No. 1
1000 lb. Motorcycle lift
91764
Set up and operating inStructionS
Visit our website at: http://www.harborfreight.com
read this material before using this product.
failure to do so can result in serious injury.
SaVe thiS Manual.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be dr
Summary of the content on the page No. 2
notice is used to SaVe thiS Manual address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, caution, without operating, inspection, maintenance and the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual practices not related to near the assembly diagram (or month personal injury. and year of purchase if product has no number). Keep this manual and th
Summary of the content on the page No. 3
9. Keep clear of load while lifting, 21. Do not allow anyone on the lift or the moving and lowering. motorcycle or the ATV while on the lift. 10. lower load slowly. 22. Raise Casters off the ground to 11. do not use for aircraft purposes. prevent movement before loading, unloading, raising, or lowering. 12. inspect before every use; do not use if parts are loose or damaged. 23. Before lowering, remove all tools and equipment from under lift. 13. Keep work area clean and well lit. Clutter
Summary of the content on the page No. 4
frame assembly frame SpecificationS assembly 1 Rated Capacity 1000 lb. ( / ton) 2 1 st 18- / ” (1 lock) 2 Height Range 3 nd 27- / ” (2 lock) 4 front Tire Vise axle (52) Wheel Stop cotter Features Leveling Pads pin (47) Swivel Casters (front) Locking Bar 1 3 front Platform Dimensions 86- / ” L x 26- / ” W 2 4 Wheel (44) Weight 350 lb. Washer (43) 2. Place a Front Wheel (44) and Washer unpacKing (43) on the end of the Front Axle (52). Insert a Cotter Pin (47) through the When unpacking, m
Summary of the content on the page No. 5
platform (35) 6. Turn the Lifting Screws (18) by means of removing Fastners 30, counterclockwise to lower the lift onto 31, 23 and 34. Bolts and Nuts to be the Casters. tightened only after determining the proper tire mounting position. access 10. Attach the Stop Plate (32) to the panel (36) Platform using Bolts (33), Washers (23), Lock Washers (31), and Nuts (30). Do not tighten. ramp (37) 11. Fit the Lift Foot Pedal (11) over the r-pins Pump Piston Spindle (09). Washers (23) (04)
Summary of the content on the page No. 6
in the Front Lifting Arm (38) so the lift lifting cannot be accidentally lowered. 1. Position the lift on a flat, level, hard 8. Gently press release foot pedal to surface able to support at least 1350 lower the platform to reset the load lb. on Locking Bar (22) and not on the lift 2. Turn the Lifting Screws (18) clockwise jack. Slightly pump up the platform to to evenly raise the Casters (14) off free the Locking Bar. the ground and limit movement. lowering 3. With the Access Panel (
Summary of the content on the page No. 7
2. Always use at least 2 wheel chocks use. if the lift appears not to be (one for a front ATV wheel and one working properly, follow Bleeding for a back ATV wheel) to prevent instructions. movement of the ATV while it is 3. The mechanical parts of the Lift, such being worked on. Wheel chocks are as the pedal lift and release shafts not included, but are available from should be occasionally lubricated with Harbor Freight Tools (recommend heavy oil or grease. a non-slip rubber Wheel Ch
Summary of the content on the page No. 8
note: Do not tamper with the check valves. Any repairs should be performed by a qualified technician. checking and filling hydraulic fluid 1. Lower the lift completely. Remove the Access Panel (36) and the Oil Plug (P23) underneath. 2. The oil level should be even with the bottom of the filler plug hole. You should be able to see the oil. 3. If the oil level is low, add SAE Hydraulic Jack fluid only. Avoid mixing different brands of oils. do not use any other fluid or brake fluid. b
Summary of the content on the page No. 9
liMited 90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
Summary of the content on the page No. 10
partS liStS and diagraMS Main parts list part description Q’ty part description Q’ty 01 Hydraulic Pump 1 30 Nut M10 4 02 Link 1 31 Lock Washer 10 4 03 Pin 1 32 Stop Plate 1 04 R-Pin 5 33 Bolt M10*25 4 05 Release Valve Spindle 1 34 Vise 1 06 Link 1 35 Platform 1 07 Pin 2 36 Access Panel 1 09 Pump Piston Spindle 1 37 Ramp 1 10 Release Foot Pedal 1 38 Front Lifting Arm 1 11 Lift Foot Pedal 1 39 Rear Lifting Arm 1 12 Bolt M6*25 8 40 Lifting Arm Spindle 1 13 Washer 6 17 41 Bolt M8*12 1 14 Caster Fron
Summary of the content on the page No. 11
Main assembly diagram 35 SKU 91764 for technical questions, please call 1-800-444-3353. Page 11
Summary of the content on the page No. 12
pump parts list and diagram part description Q’ty part description Q’ty P01 Base 1 P19 Screw 1 P02 Steel Ball 2 P20 O-Ring 1 P03 Spring 2 P21 Screw 1 P04 Screw 2 P22 Screw Protector 1 P05 Copper Washer 1 P23 Oil Plug 1 P06 Regulating Plug 1 P24 Seal Ring 1 P07 Sealing Ring 1 P25 Set Nut 1 P08 Pump Piston 1 P27 Nylon Ring 1 P09 Union Nut 1 P28 Reservoir 1 P10 Union Nut 1 P29 Nylon Ring 1 P11 Screw 1 P30 Cylinder 1 P12 Spring 1 P31 O-Ring 1 P13 Release Valve 1 P32 Nylon Ring 1 P14 O-Ring 1 P33 Pis
