Summary of the content on the page No. 1
RECTANGULAR GAS FIREPIT
RECTANGULAR CALENTADOR DE
FUEGO A GAS
OWNER’S MANUAL / MANUAL DEL PROPIETARIO
ASSEMBLY AND OPERATING INSTRUCTIONS
INSTRUCCIONES DE ARMADO Y OPERACIÓN
SAVE THIS MANUAL FOR FUTURE REFERENCE
GUARDE ESTE MANUAL PARA REFERENCIA FUTURA
WARNING/ADVERTENCIA
NOTICE TO INSTALLER:
HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS AND INSTRUCTIONS
LEAVE THESE INSTRUCTIONS
ARE IGNORED. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS
WITH THE FIREPIT OWNER FOR
MANUAL TO AVOID PERS
Summary of the content on the page No. 2
IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR FIREPIT AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR FIREPIT. WHEN YOU SEE THE SAFETY ALERT SYMBOL PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR FIREPIT. WARNING If the information in this manual is not followed exactly, fire or explosion may
Summary of the content on the page No. 3
TABLE OF CONTENTS Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Firepit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cylinder Specifications / Cylinder Installation . . . . . . . . . . . . . . . . . . . . . . . 4–7 Leak Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9 Pre-start Check List . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
IMPORTANT SAFETY INFORMATION WARNING • The installation must conform with local codes or, in the absences of local codes, with the National Fuel Code, ANSI Z223.1. • The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with The National Electrical Code, ANSI/NFPA70. (If applicable) • Always place the firepit on a firm and level surface. • Solid fuels shall not be burned in this gas firepit. • The firepit shall be used onl
Summary of the content on the page No. 5
RECTANGULAR GAS FIREPIT SPECIFICATIONS: Product name Rectangular Gas Firepit Model No. 832-7000-S Rated Heat Output 40,000 BTU/HR Fuel Propane-LPG Gas Supply 20 lb. LP-gas cylinder Manifold Pressure 11 inches water column Orifice Size (diameter) 1.96(0~+0.02)mm Gas Supply Pressure Maximum 250 PSI WARNING LP GAS CYLINDER (NOT SUPPLIED WITH THIS FIREPIT) The LP cylinder is available for purchase at the same location the firepit was purchased. The LP (Liquid Propane) gas cylinder specifically desig
Summary of the content on the page No. 6
WARNING • Turn off the cylinder valve when your firepit is not in use. • Handle the tank with care. • Always secure the cylinder in an upright position. • Never connect an unregulated LP gas cylinder to your firepit. • DO NOT expose LP gas cylinders to excessive heat or ignition sources. • DO NOT store a spare LP gas cylinder under or near your firepit. • Allow only qualified LP gas dealers to fill or repair your LP gas cylinder. • DO NOT allow the cylinder to be filled beyond 80% capacity. • R
Summary of the content on the page No. 7
WARNING FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder. • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel propane gas vapors. The vapor is combustible and if it comes in contact with a spark sour
Summary of the content on the page No. 8
WARNING • Never use your firepit without leak testing all gas connections and hoses. See the section on "Leak Testing" in this manual for proper procedures. WARNING The pressure regulator and hose assembly supplied with your gas firepit must be used. • DO NOT attempt to connect it to any other fuel supply source such as a natural gas line. • DO NOT use any other pressure regulator/hose assembly other than the one supplied with your firepit. Replacement pressure regulator/hose assembly must be pa
Summary of the content on the page No. 9
DANGER LEAK TESTING: To prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the firepit is in use or while firepit is still hot. WARNING WHEN TO PERFORM A LEAK TEST: • After assembling your firepit and before lighting for the first time, even if purchased fully assembled. • Every time th
Summary of the content on the page No. 10
6. Check each place listed (A–K) for growing bubbles which indicates a leak. 7. Turn off gas supply at cylinder valve. 8. Turn on the control knob to release gas pressure in hose. 9. Turn the control knob to "OFF" position. 10. Tighten any leaking connections. 11. Repeat soapy water test until no leaks are detected. 12. Turn off gas supply at cylinder valve until you are ready to use your firepit. 13. Wash off soapy residue with cold water and towel dry. 14. Wait 5 minutes to allow all gas to e
Summary of the content on the page No. 11
E T I N G I WARNING Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual. WARNING LIGHTING INSTRUCTIONS: Follow the instructions exactly. 1. REMOVE THE FIREPIT COVER before attempting to light the burner so that gas fumes do not accumulate inside the firepit. An explosion could occur if firepit cover is down. 2. Check that the burner control knob and the cylinder val
Summary of the content on the page No. 12
TURNING OFF THE GAS FIREPIT: 1. Turn off the cylinder valve. 2. Turn burner control knob to the "OFF" position. Note: Turn off LP cylinder first to prevent gas from being left in the system under pressure. CAUTION: • The cylinder valve should always be in the off, or closed, position when the firepit is not in use. To turn off the cylinder valve, turn knob clockwise until it stops. Note: Observe flame height when lit: Flame should be a Blue/Yellow color and appear as illustrated. To clean lava r
Summary of the content on the page No. 13
TROUBLE SHOOTING PROBLEM OBSERVED POSSIBLE CAUSE CORRECTIVE MEASURES Gas leakage Check all gas connections Gas odor Delayed ignition Low gas pressure Check gas supply pressure Clogged or dirty burner ports Clean burner ports-see manual section Bad battery Change battery Incorrect burner flame Incorrect gas supply or pressure Check gas supply pressure Clogged or dirty burner ports Clean burner ports 12
Summary of the content on the page No. 14
PARTS BAG CONTENTS Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before you begin the installation process. Your Parts Bag will include: Qty. Qty. 34 M6 X 14mm Bolts 1 M5 Nut 1 M5 Washer 4 M4 X 10mm Bolts 8 M6 Washers 1 AA/1.5V Alkaline Battery 4 M4 X 30mm Bolts M6 X 14mm Bolts M4 X 10mm M5 Washer M5 Nut Bolts M4 X 30mm Bolts M6 Washers AA/1.5V Alkaline Battery 13
Summary of the content on the page No. 15
ASSEMBLY INSTRUCTIONS READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR FIREPIT. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT. ® The following tools are required to assemble this Charmglow Rectangular Gas Firepit: • Flathead Screwdriver • Hex Nut Wrench PARTS LIST: 1 1 Cover Handle 10 1 Front Side Panel 2 1 Cover 11 1 Left Side Panel 3 1 Lava Rocks 12 1 Tank Holder Support 4 1 Firepit Grate 13 2 Strengthener Supports 5 1 Burner Asse
Summary of the content on the page No. 16
Choose a good, cleared assembly area and get a friend to help you to unpack and set up your firepit. Front & Back Table Panels CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary. Step 1 Left & Right Attach the four table panels by Table Panels using eight M6 x14mm bolts and eight M6 washers. Back Side Panel Step 2 Attach the front and back panels to the table assembly by using twelve M6 x 14mm bolts. Front Side Panel Step 3 Connect the side panel with the front
Summary of the content on the page No. 17
Step 5 Connect the drawer panel with the tank holder support by using four M6 x 14mm bolts. Attach both strengthener supports to the drawer panel and tank holder support by using four M6 x 14mm bolts. Insert cylinder clamp screw as shown. Cylinder Clamp Screw Note: With the help of a friend, turn the cart to its upright position. Step 6 Pull out the sliding tracks on the front and back panels to the furthest position. 16
Summary of the content on the page No. 18
Step 7 Align tank holder support runners with the sliding tracks on the front and rear panels. Insert runners fully until locked into position. Step 8 Place the burner assembly on the table with the control panel facing the front panel door, attach it by using four M4 x 30mm bolts. 17
Summary of the content on the page No. 19
Step 9 Insert cover handle through firepit cover and secure it to cover by using one M5 washer and M5 nut. Step 10 Firepit Cover Place firepit grate directly over burner assembly. Lava Rocks Firepit Grate Step 11 Arrange lava rocks on firepit grate. Step 12 Place firepit cover directly over firepit grate when not in use. Battery Compartment Battery Cap Step 13 Unscrew battery compartment cap, located on control panel and install the AA battery with positive end of battery towards the battery c
Summary of the content on the page No. 20
® Charmglow Rectangular Gas Firepit (Assembled) 19
