Summary of the content on the page No. 1
WS-9032U
Wireless 433 MHz
Weather Station
Instruction Manual
FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter)
FCC DISCLAIMER
This device complies with part 15 of the FCC rules. Operation is subject to the
R
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Contents
Language Page
English 2
French 23
Spanish 46
Summary of the content on the page No. 2
TABLE OF CONTENTS INVENTORY OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 About WWVB 3 Quick Set Up Guide 4 Detailed Set Up Guide Battery Installation 4 Start Up Sequence 6 Explanation of LCD Information 7 Function Key Layout 8 Program Mode Overview of Programming Sequence 8 LCD Contrast Setting 8 Time Zone Setting 8 DST ON/OFF Setting 9 Radio-controlled Time ON/OFF Setting 9 12/24-hour Time Mode Setting 9 Setting the Time/Date Manually 9 REMOTE THERMO-SENSOR 433 MHz Tempe
Summary of the content on the page No. 3
3. Do not press any buttons for at least ten minutes. If a button is pressed before the III. Explanation of LCD Information indoor weather station has received information from the TX4U sensor, no data A. The below picture highlights the LCD features. will be received from that sensor until reset. 4. Replace the battery cover. Radio-controlled II. Start Up Sequence A. Initial Start WWVB Reception 1. Immediately after the batteries have been installed, the indoor weather station Indicator will so
Summary of the content on the page No. 4
1. Press and hold the “SET” button for five seconds. 5. Press and release the “OUT/+” button to select the desired date. 2. “lcd” will appear at the top of the display and a number will flash next to it. 6. Press and release the “SET” button to confirm the date and continue to the Tem- 3. Press and release the “SET” button five more times to advance to the Manual perature Measuring Units setting. Hour setting. 4. The hour will begin to flash at the top of the display. L. Temperature Measuring Un
Summary of the content on the page No. 5
a. From the normal display mode, press and release the “OUT/+” key once to view Each remote sensor will have its own minimum and maximum values stored. the outdoor maximum temperature and humidity (“MAX” will be displayed above the outdoor temperature and humidity). E. Comfort Indicator for Indoor Temperature and Humidity b. Press and release the “OUT/+” key again to view the outdoor minimum tempera- 1. The comfort level indicator appears inbetween the indoor tempearture and ture and humidity. h
Summary of the content on the page No. 6
2. Mounting with Adhesive Tape D. Immediately remove all low powered batteries to avoid leakage and damage. a. With a nonabrasive solution, clean and dry the back of the mounting bracket and E. Opening the casings invalidates the warranty. Do not try to repair the unit. Con- the mounting surface to ensure a secure hold. The mounting surface should be tact La Crosse Technology for repairs. smooth and flat. b. Remove the protective strip from one side of the tape. TROUBLESHOOTING c. Press firml
Summary of the content on the page No. 7
WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can
Summary of the content on the page No. 8
adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDREN’S REACH. This warranty gives you speci
Summary of the content on the page No. 9
FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. La Crosse Technology Made in China All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical